Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0560-117  System Voltage  


DESCRIPTION

Battery power is constantly supplied to the BATT terminal of the hybrid vehicle control ECU to allow DTCs and freeze frame data to be retained in memory even though the power switch is turned off. The back-up power is supplied even when the power switch is off.


DTC No. INF Code DTC Detection Condition Trouble Area
P0560 117 Malfunction in the hybrid vehicle control ECU back-up power source circuit
(1 trip detection logic)
·

Auxiliary battery

·

ECU-B NO. 2 fuse

·

Wire harness or connector

·

Hybrid vehicle control ECU



Related Data List
DTC No. Data List
P0560-117 +B

WIRING DIAGRAM

A344504E08
5.302,2.135 7.083,2.5 1.781,0.365 10 false Hybrid Vehicle Control ECU 5.469,1.156 5.854,1.354 0.385,0.198 10 false G80 5.844,1.167 6.042,1.323 0.198,0.156 10 false E1 5.833,0.573 6.26,0.792 0.427,0.219 10 false BATT 5.552,0.385 5.698,0.583 0.146,0.198 10 false 3 3.594,0.427 3.74,0.625 0.146,0.198 10 false 1 5.563,0.958 5.708,1.156 0.146,0.198 10 false 6 4.052,0.438 4.198,0.635 0.146,0.198 10 false 2 3.438,0.708 4.365,0.906 0.927,0.198 10 false ECU-B NO. 2 2.021,0.74 2.469,0.885 0.448,0.146 10 false MAIN 0.948,1.635 2.042,1.865 1.094,0.229 10 false Auxiliary Battery 5.469,0.573 5.854,0.771 0.385,0.198 10 false G81

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (IG) and wait for a few seconds.



PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

2.CHECK AUXILIARY BATTERY TERMINAL (CONTACT PROBLEM)

NG

CONNECT SECURELY

2.CHECK AUXILIARY BATTERY TERMINAL (CONTACT PROBLEM)
a.

Check the connection of the auxiliary battery terminal.

OK:

The terminal is connected securely and there is no contact problem.




OK

3.INSPECT AUXILIARY BATTERY

NG

CONNECT SECURELY

3.INSPECT AUXILIARY BATTERY

OK

4.CHECK FUSE (ECU-B NO. 2)

NG

CHARGE OR REPLACE AUXILIARY BATTERY

4.CHECK FUSE (ECU-B NO. 2)
a.

Remove the ECU-B NO. 2 fuse from the No. 2 engine room relay block and No. 2 junction block assembly.


b.
A263622E02
0.594,2.521 0.656,3.01 false 0.156,0.135 0.417,0.396 0.26,0.26 10 false *1 0.583,3.01 0.781,3.208 0.198,0.198 10 false *2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
ECU-B NO. 2 fuse Power switch off Below 1 Ω


Text in Illustration
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
*2 ECU-B NO. 2 Fuse


c.

Install the ECU-B NO. 2 fuse.



OK

5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - ECU-B NO. 2 FUSE)

NG

REPLACE FUSE (ECU-B NO. 2)

5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - ECU-B NO. 2 FUSE)
a.

Remove the ECU-B NO. 2 fuse from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Disconnect connector G81 from the hybrid vehicle control ECU.


c.

Measure the resistance according to the value(s) in the table below.

NOTICE:

When taking measurements with a tester, do not apply excessive force to the tester probes to avoid damaging the fuse holder or terminals.


U183347E02
2.854,1.74 3.354,1.667 false 3.792,0.083 3.979,0.302 0.188,0.219 10 false *1 3.729,2.083 3.917,2.302 0.188,0.219 10 false *2 0.344,0.083 0.531,0.302 0.188,0.219 10 false *a 3.396,1.573 3.833,1.729 0.438,0.156 10 false BATT 2.167,1.708 2.49,1.875 0.323,0.167 10 false G81

Text in Illustration
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly *2 ECU-B NO. 2 Fuse
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
- -

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
G81-3 (BATT) - 2 (ECU-B NO. 2 fuse) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
G81-3 (BATT) or 2 (ECU-B NO. 2 fuse) - Body ground and other terminals Power switch off 10 kΩ or more



d.

Install the ECU-B NO. 2 fuse.


e.

Connect the hybrid vehicle control ECU connector.



OK

6.CHECK HARNESS AND CONNECTOR (ECU-B NO. 2 FUSE - AUXILIARY BATTERY POSITIVE TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (ECU-B NO. 2 FUSE - AUXILIARY BATTERY POSITIVE TERMINAL)
a.

Remove the ECU-B NO. 2 fuse from the No. 2 engine room relay block and No. 2 junction block assembly.


b.
A263624E01
0.146,0.182 0.371,0.352 0.225,0.170 10 *1 0.223,2.58 0.449,2.749 0.225,0.170 10 *2

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
1 (ECU-B NO. 2 fuse) - Body ground Always 11 to 14 V


Text in Illustration
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
*2 ECU-B NO. 2 Fuse


c.

Install the ECU-B NO. 2 fuse.



OK

7.RECONFIRM DTC OUTPUT (HYBRID CONTROL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.RECONFIRM DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Hybrid Control / DTC.


e.

Recheck for DTCs.

Result:
Result Proceed to
DTC P0560-117 is output again A
DTC P0560-117 is not output B



HINT:

If DTC P0560-117 is output after this inspection, replace the hybrid vehicle control ECU. If the DTC is not output, check for intermittent problems (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS) because there may be a malfunction in the wire harness or connector.



A

B