Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A0F-238  Engine Failed to Start  


DESCRIPTION

If the power management control ECU detects that the engine or transaxle gear has seized, the power management control ECU will perform fail-safe control. Also, if a substance or object is preventing the engine or transaxle internal components from rotating, the power management control ECU will perform fail-safe control.

DTC No. INF Code DTC Detection Condition Trouble Area
P0A0F 238 Engine does not start even though it is being cranked (transaxle input malfunction [engine system])
·

Hybrid vehicle transaxle assembly

·

Transmission input damper assembly

·

Power management control ECU

·

Engine



A217594E22
5.917,4.698 4.76,4.948 true 5.49,4.313 4.646,4.531 true 1.646,5.229 2.75,5.688 true 2.125,4.375 2.771,4.583 true 2.573,1.76 1.865,1.104 true 4.542,1.74 5.021,1.073 false 5.969,5.188 4.813,5.5 true 1.698,4.771 2.74,5.219 true 4.896,2 5.208,1.448 false 2.396,0.646 5.448,0.938 3.052,0.292 10 false Hybrid Vehicle Transaxle Assembly 0.313,5.927 3.292,6.271 2.979,0.344 10 false Motor Speed Reduction Planetary Gear Unit 5.208,2.552 5.979,2.844 0.771,0.292 10 false Engine 5.01,5.917 7.063,6.198 2.052,0.281 10 false Power Split Planetary Gear Unit 2.792,5.146 4.49,5.375 1.698,0.229 10 false Sun Gear (MG2) 5.26,1.354 6.948,1.771 1.688,0.417 10 false Transmission Input Damper Assembly 1.5,1 2.313,1.323 0.813,0.323 10 false MG2 2.844,4.51 3.917,4.75 1.073,0.24 10 false Ring Gear 4.042,5.417 5.083,5.76 1.042,0.344 10 false Pinion Gear 5.083,0.938 5.896,1.26 0.813,0.323 10 false MG1 3.969,4.458 5.042,4.698 1.073,0.24 10 false Ring Gear 3.698,4.885 5.396,5.115 1.698,0.229 10 false Sun Gear (MG1) 2.875,5.615 3.917,5.958 1.042,0.344 10 false Pinion Gear

CAUTION / NOTICE / HINT

HINT:
·

A seized engine, mechanical malfunction of the hybrid vehicle transaxle can be suspected.

·

If this DTC is output, the engine or transaxle gear may be seized. Be sure to check the level of the engine oil, automatic transmission fluid (ATF) and coolant before inspection.

·

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

(a)

While driving the vehicle at a speed of 20 km/h or more in EV mode, depress the accelerator pedal to start the engine, and drive the vehicle for 3 seconds or more.*1

*1: When the HV system is normal, the engine starts when the accelerator pedal is depressed halfway or more. If the HV system is malfunctioning, the engine may not start. Even in this case, if you drive the vehicle at a speed of 12 mph (20 km/h) or more in EV mode for 3 seconds or more, you can confirm this DTC.





PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
Only P0A0F-238 is output or P0A0F-238 and DTCs other than P0A1D are also output. A
P0A1D (Hybrid Powertrain Control Module) is output. B



e.

Turn the power switch off.



A

2.CHECK CRANKSHAFT PULLEY REVOLUTION (P POSITION)

B

2.CHECK CRANKSHAFT PULLEY REVOLUTION (P POSITION)
a.

Check that the shift lever is in the P position.


b.

Lift up the vehicle.


c.

Turn the crankshaft pulley using hand tools to check if the crankshaft can rotate smoothly.

CAUTION:

Do not turn the power switch on (READY) while performing this inspection. Be sure to turn the power switch off before performing this inspection, to prevent the engine from starting.


NOTICE:

Engine compression causes resistance when turning the crankshaft pulley. Check if the crankshaft rotates smoothly (or if it is locked) by manually applying sufficient torque to turn the crankshaft pulley. The torque required to turn the crankshaft pulley should be the same as for a known good vehicle of the same type.


OK:

The crankshaft rotates smoothly.



d.

Lower the vehicle.



OK

3.CLEAR DTC

NG

7.CHECK CRANKSHAFT PULLEY REVOLUTION (N POSITION)
3.CLEAR DTC
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Read and record the DTCs and freeze frame data.


e.

Clear DTCs and freeze frame data.


f.

Turn the power switch off.



NEXT

4.CHECK ENGINE RACING
4.CHECK ENGINE RACING
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (READY).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Generator (MG1) Rev, Engine Revolution.


d.

Read the Data List.


e.
A212091E14
2.094,1.958 2.365,1.469 false 0.938,1.458 1.146,1.208 1.146,1.208 1.063,1.74 false 2.198,1.156 2.708,1.344 0.51,0.188 10 false Normal 0.813,0.885 1.656,1.094 0.844,0.208 10 false Malfunction 1.583,2.458 2.094,2.646 0.51,0.188 10 false Engine 2.771,2.458 3.135,2.646 0.365,0.188 10 false MG2 0.51,2.458 0.875,2.646 0.365,0.188 10 false MG1

While the READY indicator is on, fully depress the accelerator pedal for 10 seconds.

OK:

Generator (MG1) Rev increases to approximately 3.6 times that of Engine Revolution.


HINT:

Refer to the graph for Data List confirmation of "Generator (MG1) Rev" and " Engine Revolution".

Data List ENGINE REV MG1 REV
Reference Value Approximately 1000 rpm Approximately 3600 rpm
Approximately 1500 rpm Approximately 5400 rpm
Approximately 2500 rpm Approximately 9000 rpm



f.

Turn the power switch off.



OK

5.CHECK CREEP MOVEMENT

NG

5.CHECK CREEP MOVEMENT
a.

Turn the power switch on (READY).


b.

Depress the brake pedal, move the shift lever to D, and release the brake pedal.

OK:

The wheels turn (the vehicle creeps forward).



c.

Turn the power switch off.



OK

6.CHECK ENGINE SPEED

NG

6.CHECK ENGINE SPEED
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (READY).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Motor (MG2) Revolution, Generator (MG1) Rev, Engine Revolution.


d.

Read the Data List.


e.

Move the shift lever to D.


f.

Fully depress the accelerator pedal to accelerate the vehicle from a stop.

NOTICE:

Perform this test only in an appropriate safe location, in accordance with all local laws.


OK:

The difference between Engine Revolution and 0.28 X Generator (MG1) Rev + 0.27 X Motor (MG2) Revolution is 500 rpm or more and it is maintained for 1 second.



g.

Turn the power switch off.



OK

NG

7.CHECK CRANKSHAFT PULLEY REVOLUTION (N POSITION)
a.

Lift up the vehicle.


b.

Move the shift lever to N.


c.

Turn the crankshaft pulley using hand tools to check if the crankshaft can rotate smoothly.

CAUTION:

Do not turn the power switch on (READY) while performing this inspection. Be sure to turn the power switch off before performing this inspection, to prevent the engine from starting.


NOTICE:

Engine compression causes resistance when turning the crankshaft pulley. Check if the crankshaft rotates smoothly (or if it is locked) by manually applying sufficient torque to turn the crankshaft pulley. The torque required to turn the crankshaft pulley should be the same as for a known good vehicle of the same type.


OK:

The crankshaft rotates smoothly.



d.

Lower the vehicle.



OK

NG

REPAIR OR REPLACE ENGINE