Refer to the description for DTC P0A2B-250 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A2B-250).
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| P0A2C | 247 | Short or short to GND in the motor temperature sensor circuit | ·
Wire harness or connector ·
Power management control ECU ·
Hybrid vehicle transaxle assembly (Motor temperature sensor) |
| P0A2D | 249 | Open or short to +B in the motor temperature sensor circuit |
After confirming that DTC P0A2C-247 or P0A2D-249 is output, use the intelligent tester to check "Motor Temp No1" in the power management control ECU Data List.
| Displayed Temperature | Malfunction |
|---|---|
| -40°C (-40°F) | Open circuit or short to +B |
| 215°C (419°F) | Short circuit or short to GND |
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Turn the power switch on (IG) and wait for 5 seconds or more.
| *A | for LHD |
| *B | for RHD |
Check the connection condition of the Hybrid vehicle control ECU connectors and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.
- The connector is connected securely.
- The terminals are not deformed and are connected securely.
- No water or foreign matter in the connector.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely.) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) | C |
A
B
C
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A2B-250
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely.) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) | C |
A
B
C
Check the connection condition of the C25 motor temperature sensor connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.
- The connector is connected securely.
- The terminals are not deformed and are connected securely.
- No water or foreign matter in the connector.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely.) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) | C |
A
B
C
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Motor Temp No1.
Read the Data List.
| Result | Proceed to |
|---|---|
| -40°C (-40°F) | A |
| 215°C (419°F) | B |
| Same as actual temperature | C |
Turn the power switch off.
A
B
C
Disconnect the C25 motor temperature sensor connector.
| *a | Component without harness connected
(Motor Temperature Sensor (Hybrid Vehicle Transaxle Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C25-2 (MMT) - C25-1 (MMTG) | Power switch off | 0.3436 to 1442 kΩ |
The motor temperature sensor is not available separately. If it requires replacement, replace the hybrid vehicle transaxle assembly.
Reconnect the C25 motor temperature sensor connector.
OK
NG
| *a | Component with harness connected
(Power Management Control ECU) |
Connect terminals 24 (MMT) and 25 (MMTG) of connector A38 of the power management control ECU.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Motor Temp No1.
Read the Data List.
| Tester Display | Condition | Specified Condition |
| Motor Temp No1 | Terminals MMT and MMTG connected.
Power switch on (IG) |
215°C (419°F) |
Turn the power switch off.
OK
NG
Disconnect the C25 motor temperature sensor connector.
| *a | Component without harness connected
(Motor Temperature Sensor (Hybrid Vehicle Transaxle Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C25-2 (MMT) - C25-1 (MMTG) | Power switch off | 0.3436 to 1442 kΩ |
The motor temperature sensor is not available separately. If it requires replacement, replace the hybrid vehicle transaxle assembly.
Reconnect the C25 motor temperature sensor connector.
OK
NG
Disconnect the C25 motor temperature sensor connector.
Disconnect the A38 power management control ECU connector.
| *a | Front view of wire harness connector
(to Motor Temperature Sensor) |
| *b | Rear view of wire harness connector
(to Power Management Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C25-2 (MMT) - A38-24 (MMT) | Power switch off | Below 1 Ω |
| C25-1 (MMTG) - A38-25 (MMTG) | Power switch off | Below 1 Ω |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C25-2 (MMT) or A38-24 (MMT) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| C25-1 (MMTG) or A38-25 (MMTG) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
Reconnect the A38 power management control ECU connector.
Reconnect the C25 motor temperature sensor connector.
OK
NG