Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0705-757  Transmission Range Sensor Circuit  


DESCRIPTION

The shift lever position sensor can send 7 different switch signals to the hybrid vehicle control ECU. The hybrid vehicle control ECU uses the signals to detect the shift lever position (P, R, N, D, or B). The hybrid vehicle control ECU also uses this information to determine intended direction of travel (forward or reverse).

DTC No. INF Code DTC Detection Condition Trouble Area
P0705 757 Logical inconsistency in shift sensor output values
·

Wire harness or connector

·

Shift lever position sensor

·

Hybrid vehicle control ECU



WIRING DIAGRAM

A264043E25
1.469,0.375 3.156,0.635 1.688,0.26 10 false From IGCT NO. 2 Fuse 0.552,3.74 1.115,4.073 0.563,0.333 10 false C23 0.552,3.906 2.333,4.177 1.781,0.271 10 false Shift Lever Position Sensor 4.865,3.75 5.344,4.073 0.479,0.323 10 false A72 4.865,3.917 6.99,4.135 2.125,0.219 10 false Hybrid Vehicle Control ECU 0.969,0.75 1.333,1 0.365,0.25 10 false +B 1.99,0.792 2.156,0.958 0.167,0.167 10 false P 4.854,0.802 5.021,0.969 0.167,0.167 10 false P 1.99,1.135 2.146,1.292 0.156,0.156 10 false R 4.844,1.125 5,1.281 0.156,0.156 10 false R 1.99,1.51 2.146,1.667 0.156,0.156 10 false N 4.854,1.51 5.01,1.667 0.156,0.156 10 false N 1.854,1.844 2.323,2.115 0.469,0.271 10 false DB1 4.865,1.844 5.281,2.104 0.417,0.26 10 false DB1 4.854,2.188 5.271,2.417 0.417,0.229 10 false DB2 1.844,2.177 2.396,2.458 0.552,0.281 10 false DB2 1.906,2.521 2.25,2.75 0.344,0.229 10 false PR 4.854,2.531 5.188,2.74 0.333,0.208 10 false PR 1.823,2.896 2.375,3.146 0.552,0.25 10 false PNB 4.833,2.906 5.333,3.229 0.5,0.323 10 false PNB 2.208,0.792 2.375,0.99 0.167,0.198 10 false 8 0.792,0.542 0.948,0.698 0.156,0.156 10 false 7 2.208,1.125 2.365,1.281 0.156,0.156 10 false 9 2.208,1.51 2.365,1.667 0.156,0.156 10 false 2 2.198,1.844 2.354,2 0.156,0.156 10 false 1 2.198,2.177 2.354,2.333 0.156,0.156 10 false 6 2.208,2.521 2.365,2.677 0.156,0.156 10 false 3 2.198,2.896 2.354,3.052 0.156,0.156 10 false 4 4.604,1.51 4.958,1.802 0.354,0.292 10 false 20 4.604,0.792 4.885,1.042 0.281,0.25 10 false 21 4.594,1.125 4.885,1.375 0.292,0.25 10 false 15 4.604,1.854 4.917,2.094 0.313,0.24 10 false 26 4.594,2.188 4.885,2.438 0.292,0.25 10 false 14 4.594,2.531 4.927,2.771 0.333,0.24 10 false 17 4.594,2.906 4.958,3.188 0.365,0.281 10 false 34

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (IG).

2.

Slowly move the shift lever from P to B then back to P.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (SHIFT POSITION)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Shift Sensor SW - P, Shift Sensor SW - R, Shift Sensor SW - N, Shift Sensor SW - DB1, Shift Sensor SW - DB2, Shift Sensor SW - PR, Shift Sensor SW - PNB.


d.

While slowly moving the shift lever from P to B, then back to P, read the Data List (shift position) displayed on the intelligent tester.

HINT:

Be sure to move the shift lever slowly.


Result:
ECU Data List Shift Position
P R N D B
Shift Sensor SW-P ON OFF OFF OFF OFF
Shift Sensor SW-R OFF ON OFF OFF OFF
Shift Sensor SW-PR ON ON OFF OFF OFF
Shift Sensor SW-N OFF OFF ON OFF OFF
Shift Sensor SW-DB1 OFF OFF OFF ON ON
Shift Sensor SW-DB2 OFF OFF OFF ON ON
Shift Sensor SW-PNB ON OFF ON OFF ON



e.

Enter the following menus: Powertrain / Hybrid Control / DTC.


f.

Check if DTCs are output.

OK:

DTC P0705-757 is not output.



g.

Turn the power switch off.



OK

2.CHECK FOR INTERMITTENT PROBLEMS

NG

3.CHECK SHIFT LEVER POSITION SENSOR
2.CHECK FOR INTERMITTENT PROBLEMS

OK

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

3.CHECK SHIFT LEVER POSITION SENSOR
a.

Turn the power switch on (IG).


b.
U183276E02
1.198,1.906 0.833,2.458 false 1.344,1.771 1.375,2.469 false 1.385,1.771 1.813,2.479 false 1.802,1.073 1.625,1.844 false 1.26,1.771 1.354,1.052 false 1.667,1.844 2.167,1.073 false 1.198,1.844 0.865,1.073 false 0.646,2.479 0.969,2.677 0.323,0.198 10 false PNB 0.708,0.875 1.031,1.031 0.323,0.156 10 false DB1 1.323,2.5 1.458,2.656 0.135,0.156 10 false R 1.729,2.5 2.094,2.656 0.365,0.156 10 false DB2 1.271,0.875 1.5,1.073 0.229,0.198 10 false PR 2.156,0.885 2.385,1.083 0.229,0.198 10 false N 0.229,0.198 0.479,0.438 0.25,0.24 10 false *a 1.302,2.927 1.573,3.094 0.271,0.167 10 false A72 1.781,0.875 2.01,1.073 0.229,0.198 10 false P

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A72-21 (P) - Body ground Power switch on (IG)
Shift lever in P
7.5 to 14 V
A72-21 (P) - Body ground Power switch on (IG)
Any position except shift lever in P
0 to 1.5 V
A72-15 (R) - Body ground Power switch on (IG)
Shift lever in R
7.5 to 14 V
A72-15 (R) - Body ground Power switch on (IG)
Any position except shift lever in R
0 to 1.5 V
A72-17 (PR) - Body ground Power switch on (IG)
Shift lever in P or R
7.5 to 14 V
A72-17 (PR) - Body ground Power switch on (IG)
Any position except shift lever in P and R
0 to 1.5 V
A72-20 (N) - Body ground Power switch on (IG)
Shift lever in N
7.5 to 14 V
A72-20 (N) - Body ground Power switch on (IG)
Any position except shift lever in N
0 to 1.5 V
A72-26 (DB1) - Body ground Power switch on (IG)
Shift lever in D or B
7.5 to 14 V
A72-26 (DB1) - Body ground Power switch on (IG)
Any position except shift lever in D and B
0 to 1.5 V
A72-14 (DB2) - Body ground Power switch on (IG)
Shift lever in D or B
7.5 to 14 V
A72-14 (DB2) - Body ground Power switch on (IG)
Any position except shift lever in D and B
0 to 1.5 V
A72-34 (PNB) - Body ground Power switch on (IG)
Shift lever in P, N or B
7.5 to 14 V
A72-34 (PNB) - Body ground Power switch on (IG)
Any position except shift lever in P, N and B
0 to 1.5 V


Text in Illustration
*a Component with harness connected
(Hybrid Vehicle Control ECU)


c.

Turn the power switch off.



OK

NG

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the shift lever position sensor connector.


b.

Turn the power switch on (IG).


c.
U158851E02
1.938,1.833 1.75,1.438 false 1.875,1.854 2.073,2.042 0.198,0.188 10 false +B 0.24,1.146 0.542,1.323 0.302,0.177 10 false C23 0.302,0.125 0.5,0.313 0.198,0.188 10 false *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C23-7 (+B) - Body ground Power switch on (IG) 7.5 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Shift Lever Position Sensor)

NOTICE:

Turning the power switch on (IG) with the shift lever position sensor connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



d.

Turn the power switch off.


e.

Connect the shift lever position sensor connector.



OK

5.INSPECT SHIFT LEVER POSITION SENSOR

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT

5.INSPECT SHIFT LEVER POSITION SENSOR
a.

Disconnect the shift lever position sensor connector.


b.
U158988E02
1.99,1.458 2.219,1.854 false 1.729,1.438 1.802,1.854 false 1.479,1.448 1.469,1.865 false 1.344,1.458 1.208,1.823 false 1.854,1.115 2.229,0.479 false 1.604,1.115 1.656,0.469 false 1.417,1.115 1.188,0.5 false 1.271,1.135 0.844,0.76 false 0.115,0.083 0.354,0.24 0.24,0.156 10 false *a 2.125,0.292 2.448,0.458 0.323,0.167 10 false DB1 2.125,1.875 2.448,2.042 0.323,0.167 10 false DB2 1.698,1.875 1.938,2.042 0.24,0.167 10 false +B 1.417,1.885 1.583,2.073 0.167,0.188 10 false P 1.073,1.844 1.25,2.021 0.177,0.177 10 false R 1.594,0.271 1.75,0.427 0.156,0.156 10 false N 1.021,0.313 1.26,0.5 0.24,0.188 10 false PR 0.469,0.635 0.823,0.833 0.354,0.198 10 false PNB 2.875,1.125 3.146,1.292 0.271,0.167 10 false C23

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C23-7 (+B) - C23-3 (PR) Shift lever in P Below 1 Ω
C23-7 (+B) - C23-4 (PNB) Below 1 Ω
C23-7 (+B) - C23-8 (P) Below 1 Ω
C23-7 (+B) - C23-1 (DB1), C23-2 (N), C23-6 (DB2) and C23-9 (R) 10 kΩ or higher
C23-7 (+B) - C23-3 (PR) Shift lever in R Below 1 Ω
C23-7 (+B) - C23-9 (R) Below 1 Ω
C23-7 (+B) - C23-1 (DB1), C23-2 (N), C23-4 (PNB), C23-6 (DB2) and C23-8 (P) 10 kΩ or higher
C23-7 (+B) - C23-2 (N) Shift lever in N Below 1 Ω
C23-7 (+B) - C23-4 (PNB) Below 1 Ω
C23-7 (+B) - C23-1 (DB1), C23-3 (PR), C23-6 (DB2), C23-8 (P) and C23-9 (R) 10 kΩ or higher
C23-7 (+B) - C23-1 (DB1) Shift lever in D Below 1 Ω
C23-7 (+B) - C23-6 (DB2) Below 1 Ω
C23-7 (+B) - C23-2 (N), C23-3 (PR), C23-4 (PNB), C23-8 (P) and C23-9 (R) 10 kΩ or higher
C23-7 (+B) - C23-1 (DB1) Shift lever in B Below 1 Ω
C23-7 (+B) - C23-4 (PNB) Below 1 Ω
C23-7 (+B) - C23-6 (DB2) Below 1 Ω
C23-7 (+B) - C23-2 (N), C23-3 (PR), C23-8 (P) and C23-9 (R) 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Shift Lever Position Sensor)

HINT:

Terminal No. 5 on the component side connector is empty.



c.

Connect the shift lever position sensor connector.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG