Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0617-142  Starter Relay Circuit High  


DESCRIPTION

The hybrid vehicle control ECU monitors the ST signal received from the certification ECU (smart key ECU assembly). When an error is detected in the ST signal, this DTC is stored.

DTC No. INF Code DTC Detection Condition Trouble Area
P0617 142 An ST signal from the hybrid vehicle control ECU is on when the power switch is off.
(2 trip detection logic)
·

Hybrid vehicle control ECU

·

Wire harness or connector

·

Certification ECU (smart key ECU assembly)



WIRING DIAGRAM

A148900E24
1.635,1.646 1.969,1.823 0.333,0.177 10 false ST2 5.375,1.646 5.708,1.823 0.333,0.177 10 false ST2 5.156,1.646 5.302,1.833 0.146,0.188 10 false 9 2.021,1.646 2.292,1.833 0.271,0.188 10 false 7 0.271,3.135 2.438,3.594 2.167,0.458 10 false Certification ECU (Smart Key ECU Assembly) 0.271,2.969 0.635,3.167 0.365,0.198 10 false G77 4.948,3.167 6.76,3.375 1.813,0.208 10 false Hybrid Vehicle Control ECU 4.938,3 5.302,3.198 0.365,0.198 10 false G80

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch off and wait for 30 seconds or more.

2.

Turn the power switch on (READY) and wait for 15 seconds or more.

3.

Turn the power switch off and wait for 30 seconds or more.



PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

2.CHECK CONNECTOR CONNECTION CONDITION (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) CONNECTOR)

NG

CONNECT SECURELY

2.CHECK CONNECTOR CONNECTION CONDITION (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) CONNECTOR)
a.

Check the connector connection condition of the certification ECU (smart key ECU assembly).

HINT:

Refer to the Service Bulletin for the installation position.


OK:

The connector is connected securely and there are no contact problems.




OK

3.CHECK HARNESS AND CONNECTOR (ST2 TERMINAL VOLTAGE)

NG

CONNECT SECURELY

3.CHECK HARNESS AND CONNECTOR (ST2 TERMINAL VOLTAGE)
a.

Turn the power switch off.


b.
U183275E02
2.135,1.771 2.49,1.188 false 2.479,1.01 2.802,1.208 0.323,0.198 10 false ST2 0.229,0.198 0.479,0.438 0.25,0.24 10 false *a 1.958,2.521 2.26,2.688 0.302,0.167 10 false G80

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G80-9 (ST2) - Body ground Power switch off Below 1 V


Text in Illustration
*a Component with harness connected
(Hybrid Vehicle Control ECU)



OK

NG

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - HYBRID VEHICLE CONTROL ECU)
4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect connector G77 from the certification ECU (smart key ECU assembly) connector.


b.
U183275E02
2.135,1.771 2.49,1.188 false 2.479,1.01 2.802,1.208 0.323,0.198 10 false ST2 0.229,0.198 0.479,0.438 0.25,0.24 10 false *a 1.958,2.521 2.26,2.688 0.302,0.167 10 false G80

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G80-9 (ST2) - Body ground Power switch off Below 1 V


Text in Illustration
*a Component with harness connected
(Hybrid Vehicle Control ECU)


c.

Connect the certification ECU (smart key ECU assembly) connector.



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR