Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0516-769  Battery Temperature Sensor Circuit Low  P0517-770  Battery Temperature Sensor Circuit High  


DESCRIPTION

The battery thermometer sensor detects the auxiliary battery temperature. The resistance of the battery thermometer sensor built into the thermistor changes in accordance with changes in the auxiliary battery temperature. The lower the auxiliary battery temperature, the higher the battery thermometer sensor resistance. Conversely, the higher the temperature, the lower the resistance. The battery thermometer sensor is connected to the power management control ECU. A voltage of 5 V is supplied to the battery thermometer sensor from the THB terminal of the power management control ECU through its internal resistor R. This means that resistor R and the battery thermometer sensor are connected in series. The voltage at the THB terminal and the resistance value change in accordance with changes in the auxiliary battery temperature. Based on this signal, the power management control ECU reduces the charging current when the auxiliary battery temperature is high to protect the auxiliary battery.

HINT:

Characteristics of the battery thermometer sensor resistance (reference values) are as follows.

Terminal THB
(with Connector Disconnected)
Resistance Ambient Temperature
THB - E2 4.5 to 5.5 V 3.00 to 3.73 kΩ Approximately 10°C (50°F)
1.60 to 1.80 kΩ Approximately 25°C (77°F)
0.80 to 1.00 kΩ Approximately 40°C (104°F)


A266952E10
0.885,1.219 1.917,1.365 1.031,0.146 10 false Resistance (kΩ) 5.167,2.344 6.573,2.49 1.406,0.146 10 false Temperature (°C (°F)) 2.396,2.24 2.583,2.385 0.188,0.146 10 false 10 2.333,2.406 2.615,2.552 0.281,0.146 10 false (50) 2.792,2.406 3.073,2.552 0.281,0.146 10 false (68) 3.25,2.406 3.531,2.552 0.281,0.146 10 false (86) 3.667,2.406 4.031,2.552 0.365,0.146 10 false (104) 4.125,2.406 4.49,2.552 0.365,0.146 10 false (122) 4.573,2.406 4.958,2.552 0.385,0.146 10 false (140) 2.844,2.24 3.042,2.385 0.198,0.146 10 false 20 3.302,2.24 3.5,2.385 0.198,0.146 10 false 30 3.771,2.24 3.958,2.385 0.188,0.146 10 false 40 4.219,2.24 4.427,2.385 0.208,0.146 10 false 50 4.677,2.24 4.885,2.385 0.208,0.146 10 false 60 2.146,2.115 2.396,2.26 0.25,0.146 10 false 0.0 2.146,1.885 2.396,2.031 0.25,0.146 10 false 0.5 2.146,1.656 2.396,1.802 0.25,0.146 10 false 1.0 2.146,1.438 2.396,1.583 0.25,0.146 10 false 1.5 2.146,1.208 2.396,1.354 0.25,0.146 10 false 2.0 2.146,0.99 2.396,1.135 0.25,0.146 10 false 2.5 2.146,0.76 2.396,0.906 0.25,0.146 10 false 3.0 2.146,0.542 2.396,0.688 0.25,0.146 10 false 3.5 2.146,0.313 2.396,0.458 0.25,0.146 10 false 4.0


DTC No. INF Code DTC Detection Condition Trouble Area
P0516 769 Malfunction in the battery thermometer sensor circuit (short to GND)
·

Battery thermometer sensor

·

Wire harness or connector

·

Power management control ECU


P0517 770 Malfunction in the battery thermometer sensor circuit (open or short to +B)

WIRING DIAGRAM

A259938E53
4.479,3.083 6.615,3.448 2.135,0.365 10 false Power Management Control ECU 4.479,2.927 5.01,3.208 0.531,0.281 10 false G57 1.052,3.083 2.958,3.448 1.906,0.365 10 false Battery Thermometer Sensor 1.052,2.927 1.656,3.135 0.604,0.208 10 false M43 2.146,1.083 2.458,1.281 0.313,0.198 10 false THB 2.542,1.083 2.677,1.281 0.135,0.198 10 false 2 2.542,2.094 2.677,2.292 0.135,0.198 10 false 1 4.563,1.083 4.76,1.281 0.198,0.198 10 false 28 4.563,2.094 4.76,2.292 0.198,0.198 10 false 30 2.25,2.094 2.458,2.292 0.208,0.198 10 false E2 4.813,1.083 5.125,1.281 0.313,0.198 10 false THB 4.823,2.094 5.26,2.292 0.438,0.198 10 false ETHB

CAUTION / NOTICE / HINT

HINT:
·

Read the freeze frame data using the intelligent tester. In the freeze frame data, some information is recorded about the vehicle conditions at the moment a malfunction occurred. This information can be helpful when troubleshooting.

·

After confirming that DTC P0516-769 or P0517-770 is output, use the intelligent tester to check "Auxiliary Batt Temperature" in the Hybrid Control Data List.

Displayed Temperature Malfunction
-40°C (-40°F) Open circuit or short to +B
215°C (419°F) Short circuit or short to GND

·

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

(a)

Turn the power switch on (IG) and wait for 5 seconds or more.




PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)
a.
A279820E01
0.154,0.041 0.381,0.290 0.227,0.249 10 *A 0.154,2.361 0.381,2.610 0.227,0.249 10 *B

Check the connector connections and contact pressure of the relevant terminals for the power management control ECU connectors (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

Text in Illustration
*A for LHD
*B for RHD

OK:

The connectors are connected securely and there are no contact pressure problems.




OK

2.READ VALUE USING INTELLIGENT TESTER (AUXILIARY BATT TEMPERATURE)

NG

CONNECT SECURELY

2.READ VALUE USING INTELLIGENT TESTER (AUXILIARY BATT TEMPERATURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Batt Temperature.


d.

Read the Data List.

Result:
Result Proceed to
-40°C (-40°F) A
215°C (419°F) B
Same as actual temperature C



e.

Turn the power switch off.



A

3.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN)

B

5.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT)

C

3.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN)
a.
A267463

Disconnect connector M43 from the battery thermometer sensor.


b.
U158904E02
1.594,1.229 1.229,1.594 false 1.813,1.219 2.229,1.594 false 0.521,0.969 0.813,1.135 0.292,0.167 10 false M43 0.146,0.094 0.344,0.271 0.198,0.177 10 false *a 2.052,1.594 2.375,1.771 0.323,0.177 10 false THB 1.094,1.594 1.313,1.771 0.219,0.177 10 false E2

Connect terminals 2 (THB) and 1 (E2) of vehicle side connector M43 of the battery thermometer sensor.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the power switch on (IG).


e.

Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Batt Temperature.


f.

Read the Data List.

OK:
Tester Display Condition Specified Condition
Auxiliary Batt Temperature Terminals THB and E2 connected.
Power switch on (IG)
215°C (419°F)


Text in Illustration
*a Front view of wire harness connector
(to Battery Thermometer Sensor)


g.

Turn the power switch off.


h.

Connect the battery thermometer sensor connector.



OK

REPLACE BATTERY THERMOMETER SENSOR

NG

4.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BATTERY THERMOMETER SENSOR)
4.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BATTERY THERMOMETER SENSOR)
a.
U183261E02
2.188,1.906 1.948,2.333 false 2.281,1.906 2.521,2.333 false 1.969,2.646 2.25,2.813 0.281,0.167 10 false G57 0.177,0.156 0.448,0.323 0.271,0.167 10 false *a 2.406,2.344 2.719,2.51 0.313,0.167 10 false THB 1.729,2.333 2.125,2.5 0.396,0.167 10 false ETHB

Connect terminals 28 (THB) and 30 (ETHB) of connector G57 of the power management control ECU.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Batt Temperature.


e.

Read the Data List.

OK:
Tester Display Condition Specified Condition
Auxiliary Batt Temperature Terminals THB and ETHB connected.
Power switch on (IG)
215°C (419°F)


Text in Illustration
*a Component with harness connected
(Power Management Control ECU)


f.

Turn the power switch off.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

5.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT)
a.
A267463

Disconnect connector M43 from the battery thermometer sensor.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Enter the following menus: Powertrain / Hybrid Control / Data List / Auxiliary Batt Temperature.


e.

Read the Data List.

OK:
Tester Display Switch Condition Specified Condition
Auxiliary Batt Temperature Power switch on (IG) -40°C (-40°F)



f.

Turn the power switch off.


g.

Connect the battery thermometer sensor connector.



OK

REPLACE BATTERY THERMOMETER SENSOR

NG

6.CHECK HARNESS AND CONNECTOR (BATTERY THERMOMETER SENSOR - POWER MANAGEMENT CONTROL ECU)
6.CHECK HARNESS AND CONNECTOR (BATTERY THERMOMETER SENSOR - POWER MANAGEMENT CONTROL ECU)
a.

Disconnect connector M43 from the battery thermometer sensor.


b.

Disconnect connector G57 from the power management control ECU.


c.
A388951E01
2.333,0.833 2.75,1.083 0.417,0.25 1.167,3.583 1.583,3.833 0.417,0.25 1.021,1.583 1.438,1.167 false 2.073,1.583 1.719,1.167 false 1.76,4.25 2.177,3.833 false 2.625,4.25 2.271,3.833 false 0.167,0.156 0.479,0.354 0.313,0.198 10 false *a 0.896,1.594 1.208,1.792 0.313,0.198 10 false E2 2.021,1.604 2.333,1.802 0.313,0.198 10 false THB 2.396,0.875 2.708,1.073 0.313,0.198 10 false M43 0.167,1.875 0.479,2.073 0.313,0.198 10 false *b 1.24,3.625 1.552,3.823 0.313,0.198 10 false G57 1.573,4.25 2.021,4.438 0.448,0.188 10 false ETHB 2.542,4.25 2.854,4.448 0.313,0.198 10 false THB

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
M43-2 (THB) - G57-28 (THB) Power switch off Below 1 Ω
M43-1 (E2) - G57-30 (ETHB) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
M43-2 (THB) or G57-28 (THB)- Body ground and other terminals Power switch off 10 kΩ or higher
M43-1 (E2) or G57-30 (ETHB)- Body ground and other terminals Power switch off 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Battery Thermometer Sensor)
*b Rear view of wire harness connector
(to Power Management Control ECU)


d.

Connect the battery thermometer sensor connector.


e.

Connect the power management control ECU connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR