Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P2120-152  Throttle / Pedal Position Sensor / Switch "D" Circuit  P2121-106  Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance  P2122-104  Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input  P2123-105  Throttle / Pedal Position Sensor / Switch "D" Circuit High Input  P2125-153  Throttle / Pedal Position Sensor / Switch "E" Circuit  P2126-109  Throttle / Pedal Position Sensor / Switch "E" Circuit Range / Performance  P2127-107  Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input  P2128-108  Throttle / Pedal Position Sensor / Switch "E" Circuit High Input  P2138-110  Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation  P2138-154  Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation  


DESCRIPTION

The accelerator pedal position sensor is mounted on the accelerator pedal to detect how much the pedal is depressed. This is a non-contact sensor with hall elements. There are 2 outputs from the sensor. One is used to detect the accelerator pedal position and the other is used as a confirmation to allow the detection of a malfunction in the sensor itself. Voltage is output from the accelerator pedal position sensor to terminals VPA1 and VPA2 of the hybrid vehicle control ECU. This voltage varies from 0 to 5 V in accordance with the accelerator pedal position. Terminal VPA2 is primarily used to detect a malfunction in the sensor itself. The hybrid vehicle control ECU determines the current accelerator pedal position and controls the hybrid control system based on signals received by terminals VPA1 and VPA2.

A222964E60
0.76,2.708 0.76,3.427 0.76,3.427 0.854,3.427 false 0.76,1.625 0.76,0.76 0.76,0.76 0.865,0.76 false 0.74,2.01 0.219,0.385 0.219,0.385 0.302,0.385 false 0.75,2.354 0.198,3.813 0.198,3.813 0.281,3.813 false 0.896,0.677 1.406,0.844 0.51,0.167 10 false Magnet 0.333,0.313 1.188,0.479 0.854,0.167 10 false Hall Element 0.333,3.74 1.188,3.906 0.854,0.167 10 false Hall Element 0.875,3.354 1.385,3.521 0.51,0.167 10 false Magnet 1.781,3.552 2.698,4.01 0.917,0.458 10 false Hybrid Vehicle Control ECU 2.854,1.771 4.01,2.385 1.156,0.615 10 false Accelerator Pedal Position Sensor Output Voltage (V) 4.5,0.708 6.781,0.938 2.281,0.229 10 false Accelerator Pedal Turning Angle (°) 4.396,4.094 6.708,4.271 2.313,0.177 10 false *1: Accelerator Pedal Fully Released 4.396,4.385 6.781,4.563 2.385,0.177 10 false *2: Accelerator Pedal Fully Depressed 0.198,4.063 1.323,4.396 1.125,0.333 10 false Accelerator Pedal Sensor Assembly 2.198,1.104 2.448,1.271 0.25,0.167 10 false 5 V 4.229,1.01 4.323,1.177 0.094,0.167 10 false 5 4.229,2.417 4.323,2.583 0.094,0.167 10 false 0 3.938,1.292 4.323,1.458 0.385,0.167 10 false 3.988 3.938,1.5 4.323,1.667 0.385,0.167 10 false 3.188 4.104,1.958 4.323,2.125 0.219,0.167 10 false 1.6 6.854,1.135 7.146,1.302 0.292,0.167 10 false 4.55 6.854,1.365 7.146,1.531 0.292,0.167 10 false 3.75 6.656,2.51 6.833,2.677 0.177,0.167 10 false 20 4.25,2.823 4.427,2.99 0.177,0.167 10 false *1 6.042,2.833 6.219,3 0.177,0.167 10 false *2 5.104,2.5 5.427,2.667 0.323,0.167 10 false 13.1 4.104,2.177 4.323,2.344 0.219,0.167 10 false 0.8 2.49,1.938 2.74,2.104 0.25,0.167 10 false 5 V 2.198,1.677 2.406,1.844 0.208,0.167 10 false AD 2.354,2.552 2.563,2.719 0.208,0.167 10 false AD

DTC No. INF Code DTC Detection Condition Trouble Area
P2120 152 Main sensor circuit wiring malfunction or level is not stable
·

Wire harness or connector

·

Accelerator pedal sensor assembly

·

Hybrid vehicle control ECU


P2121 106 Internal error of the main sensor
P2122 104 Open or short to GND in the main sensor circuit
P2123 105 Short to +B in the main sensor circuit
P2125 153 Sub sensor circuit wiring malfunction or level is not stable
P2126 109 Internal error of the sub sensor
P2127 107 Open or short to GND in the sub sensor circuit
P2128 108 Short to +B in the sub sensor circuit
P2138 110 Difference between the main sensor value and sub sensor value is large.
154 Main or sub sensor circuit wiring malfunction

WIRING DIAGRAM

A169668E68
1.771,0.531 2.313,0.823 0.542,0.292 10 false VCPA 1.781,1.896 2.417,2.208 0.635,0.313 10 false VCP2 1.865,1.021 2.458,1.323 0.594,0.302 10 false VPA 1.802,2.313 2.521,2.594 0.719,0.281 10 false VPA2 1.865,1.448 2.417,1.813 0.552,0.365 10 false EPA 0.594,3.063 1.073,3.375 0.479,0.313 10 false A31 1.802,2.76 2.385,3.052 0.583,0.292 10 false EPA2 5.323,0.469 6.135,0.865 0.813,0.396 10 false VCPA 5.125,0.469 5.49,0.729 0.365,0.26 10 false 9 5.063,0.896 5.469,1.156 0.406,0.26 10 false 30 5.063,1.344 5.458,1.677 0.396,0.333 10 false 20 5.125,1.781 5.573,2.083 0.448,0.302 10 false 8 5.063,2.208 5.396,2.469 0.333,0.26 10 false 28 5.063,2.656 5.344,2.896 0.281,0.24 10 false 18 5.323,1.781 5.948,2.073 0.625,0.292 10 false VCP2 5.323,0.906 5.958,1.281 0.635,0.375 10 false VPA 5.323,2.219 5.896,2.469 0.573,0.25 10 false VPA2 5.323,1.354 5.781,1.594 0.458,0.24 10 false EPA 5.313,2.656 5.792,2.938 0.479,0.281 10 false EPA2 0.594,3.219 2.833,3.406 2.24,0.188 10 false Accelerator Pedal Sensor Assembly 5.01,3.063 5.625,3.385 0.615,0.323 10 false A71 5.01,3.229 6.792,3.656 1.781,0.427 10 false Hybrid Vehicle Control ECU 2.26,0.458 2.708,0.771 0.448,0.313 10 false 4 2.26,0.896 2.854,1.219 0.594,0.323 10 false 6 2.26,1.333 2.677,1.635 0.417,0.302 10 false 5 2.26,1.771 2.771,2.115 0.51,0.344 10 false 1 2.26,2.219 2.594,2.51 0.333,0.292 10 false 3 2.26,2.646 2.688,2.979 0.427,0.333 10 false 2 6.104,1.719 6.344,1.865 0.24,0.146 10 false 5 V 6.104,0.438 6.344,0.583 0.24,0.146 10 false 5 V 5.802,1.156 6.302,1.521 0.5,0.365 10 false 39 kΩ +/-5% 5.792,2.479 6.313,2.833 0.521,0.354 10 false 39 kΩ +/-5%

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Wait for approximately 10 seconds with the power switch on (READY) and the shift lever in P, then fully depress and release the accelerator pedal several times.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ACCEL PEDAL POS #1, ACCEL PEDAL POS #2)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Accel Pedal Pos #1, Accel Pedal Pos #2.


d.

Read the Data List.

Result:
Tester Display Accelerator Pedal Condition Specified Condition
Accel Pedal Pos #1 Not depressed 10 to 22 %
Fully depressed 52 to 90 %
Not depressed → Fully depressed → Not depressed (Accelerator pedal should be operated slowly) Value changes progressively
Accel Pedal Pos #2 Not depressed 24 to 40 %
Fully depressed 68 to 99 %
Not depressed → Fully depressed → Not depressed (Accelerator pedal should be operated slowly) Value changes progressively



e.

Turn the power switch off.



OK

NG

2.CHECK CONNECTOR CONNECTION CONDITION (ACCELERATOR PEDAL SENSOR ASSEMBLY CONNECTOR)
2.CHECK CONNECTOR CONNECTION CONDITION (ACCELERATOR PEDAL SENSOR ASSEMBLY CONNECTOR)
a.
A389821E01
0.073,0.052 0.385,0.25 0.313,0.198 10 false *A 0.104,2.281 0.417,2.479 0.313,0.198 10 false *B

Check the connection of the accelerator pedal sensor assembly connector.

Text in Illustration
*A for LHD
*B for RHD

OK:

The connector is connected securely and there are no contact problems.




OK

3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

NG

CONNECT SECURELY

3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

4.CHECK HYBRID VEHICLE CONTROL ECU (CHECK VOLTAGE)

NG

CONNECT SECURELY

4.CHECK HYBRID VEHICLE CONTROL ECU (CHECK VOLTAGE)
a.

Disconnect connector A31 from the accelerator pedal sensor assembly.


b.

Turn the power switch on (IG).


c.
U183238E01
0.73,1.863 1.162,2.017 0.433,0.155 10 VCP2 1.304,1.863 1.737,2.017 0.433,0.155 10 EPA2 1.841,1.863 2.273,2.017 0.433,0.155 10 VCPA 2.449,1.863 2.753,2.017 0.304,0.155 10 EPA 1.338,1.144 0.946,1.828 false 1.495,1.144 1.456,1.844 false 1.812,1.144 2.055,1.828 false 1.952,1.146 2.597,1.828 false 2.876,1.031 3.141,1.212 0.264,0.181 10 A31 0.19,0.1 0.364,0.261 0.174,0.161 10 *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage :
Tester Connection Switch Condition Specified Condition
A31-4 (VCPA) - A31-5 (EPA) Power switch on (IG) 4.5 to 5.5 V
A31-1 (VCP2) - A31-2 (EPA2) Power switch on (IG) 4.5 to 5.5 V



Text in Illustration
*a Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)

d.

Turn the power switch off.


e.

Connect the accelerator pedal sensor assembly connector.



OK

5.CHECK HYBRID VEHICLE CONTROL ECU (CHECK RESISTANCE)

NG

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - ACCELERATOR PEDAL SENSOR)
5.CHECK HYBRID VEHICLE CONTROL ECU (CHECK RESISTANCE)
a.

Disconnect connector A31 from the accelerator pedal sensor assembly.


b.
U183239E01
1.322,1.886 1.755,2.041 0.433,0.155 10 VPA2 0.751,1.886 1.184,2.041 0.433,0.155 10 EPA2 2.423,1.886 2.856,2.041 0.433,0.155 10 VPA 1.982,1.886 2.286,2.041 0.304,0.155 10 EPA 1.492,1.15 0.954,1.851 false 1.948,1.152 2.095,1.835 false 2.873,1.037 3.137,1.219 0.264,0.181 10 A31 0.187,0.106 0.361,0.267 0.174,0.161 10 *a 1.649,1.146 1.552,1.852 false 2.132,1.167 2.585,1.852 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A31-6 (VPA) - A31-5 (EPA) Power switch off 28.00 to 41.61 kΩ
A31-3 (VPA2) - A31-2 (EPA2) Power switch off 28.00 to 41.61 kΩ



Text in Illustration
*a Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)

c.

Connect the accelerator pedal sensor assembly connector.



OK

NG

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - ACCELERATOR PEDAL SENSOR)
6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - ACCELERATOR PEDAL SENSOR)
a.

Disconnect connector A31 from the accelerator pedal sensor assembly.


b.
U183341E02
1,2.156 1.344,1.99 false 0.906,2.156 0.438,1.979 false 1.01,2.219 1.344,2.417 false 0.906,2.229 0.438,2.448 false 1.469,3.635 0.917,4.208 false 1.667,3.635 1.458,4.208 false 1.958,3.646 2.156,4.208 false 2.125,3.646 2.708,4.219 false 2.052,2.115 2.313,2.292 0.26,0.177 10 false A71 2.885,3.531 3.146,3.708 0.26,0.177 10 false A31 0.156,0.115 0.344,0.281 0.188,0.167 10 false *a 0.156,2.906 0.344,3.073 0.188,0.167 10 false *b 1.385,1.896 1.76,2.042 0.375,0.146 10 false EPA2 2.563,4.24 2.938,4.385 0.375,0.146 10 false VPA 0.094,1.885 0.406,2.031 0.313,0.146 10 false EPA 1.26,4.24 1.635,4.385 0.375,0.146 10 false VPA2 1.396,2.365 1.813,2.51 0.417,0.146 10 false VPA2 2.021,4.24 2.323,4.385 0.302,0.146 10 false EPA 0.104,2.385 0.406,2.531 0.302,0.146 10 false VPA 0.677,4.24 1.115,4.385 0.438,0.146 10 false EPA2

Disconnect connector A71 from the hybrid vehicle control ECU.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage :
Tester Connection Switch Condition Specified Condition
A71-30 (VPA) - Body ground Power switch on (IG) Below 1 V
A71-28 (VPA2) - Body ground Power switch on (IG) Below 1 V
A71-20 (EPA) - Body ground Power switch on (IG) Below 1 V
A71-18 (EPA2) - Body ground Power switch on (IG) Below 1 V


Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)

NOTICE:

Turning the power switch on (IG) with the hybrid vehicle control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Turn the power switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
A71-30 (VPA) - A31-6 (VPA) Power switch off Below 1 Ω
A71-20 (EPA) - A31-5 (EPA) Power switch off Below 1 Ω
A71-28 (VPA2) - A31-3 (VPA2) Power switch off Below 1 Ω
A71-18 (EPA2) - A31-2 (EPA2) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
A71-30 (VPA) or A31-6 (VPA) - Body ground and other terminals Power switch off 10 kΩ or higher
A71-20 (EPA) or A31-5 (EPA) - Body ground and other terminals Power switch off 10 kΩ or higher
A71-28 (VPA2) or A31-3 (VPA2) - Body ground and other terminals Power switch off 10 kΩ or higher
A71-18 (EPA2) or A31-2 (EPA2) - Body ground and other terminals Power switch off 10 kΩ or higher



g.

Connect the hybrid vehicle control ECU connector.


h.

Connect the accelerator pedal sensor assembly connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - ACCELERATOR PEDAL SENSOR)
a.

Disconnect connector A31 from the accelerator pedal sensor assembly.


b.

Disconnect connector A71 from the hybrid vehicle control ECU.


c.

Turn the power switch on (IG).


d.
U183342E02
1,2.083 1.406,1.771 false 0.948,2.094 0.5,1.781 false 1,2.146 1.417,2.375 false 0.906,2.156 0.448,2.365 false 1.51,3.646 1.302,4.177 false 1.344,3.646 0.792,4.156 false 1.813,3.646 2.021,4.177 false 1.979,3.646 2.51,4.177 false 2.167,2.031 2.427,2.208 0.26,0.177 10 false A71 2.833,3.5 3.094,3.677 0.26,0.177 10 false A31 0.208,0.177 0.396,0.344 0.188,0.167 10 false *a 0.208,2.844 0.396,3.01 0.188,0.167 10 false *b 1.448,1.688 2,1.833 0.552,0.146 10 false VCP2 1.781,4.188 2.219,4.333 0.438,0.146 10 false VCPA 0.073,1.667 0.479,1.813 0.406,0.146 10 false VCPA 0.521,4.188 0.917,4.333 0.396,0.146 10 false VCP2 1.448,2.323 1.938,2.469 0.49,0.146 10 false EPA2 2.396,4.188 2.698,4.333 0.302,0.146 10 false EPA 0.125,2.302 0.427,2.448 0.302,0.146 10 false EPA 1.115,4.188 1.552,4.333 0.438,0.146 10 false EPA2

Measure the voltage according to the value(s) in the table below.

Standard Voltage :
Tester Connection Switch Condition Specified Condition
A71-9 (VCPA) - Body ground Power switch on (IG) Below 1 V
A71-20 (EPA) - Body ground Power switch on (IG) Below 1 V
A71-8 (VCP2) - Body ground Power switch on (IG) Below 1 V
A71-18 (EP2A) - Body ground Power switch on (IG) Below 1 V


Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)

NOTICE:

Turning the power switch on (IG) with the hybrid vehicle control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Turn the power switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
A71-9 (VCPA) - A31-4 (VCPA) Power switch off Below 1 Ω
A71-20 (EPA) - A31-5 (EPA) Power switch off Below 1 Ω
A71-8 (VCP2) - A31-1 (VCP2) Power switch off Below 1 Ω
A71-18 (EPA2) - A31-2 (EPA2) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
A71-9 (VCPA) or A31-4 (VCPA) - Body ground and other terminals Power switch off 10 kΩ or higher
A71-20 (EPA) or A31-5 (EPA) - Body ground and other terminals Power switch off 10 kΩ or higher
A71-8 (VCP2) or A31-1 (VCP2) - Body ground and other terminals Power switch off 10 kΩ or higher
A71-18 (EPA2) or A31-2 (EPA2) - Body ground and other terminals Power switch off 10 kΩ or higher



g.

Connect the hybrid vehicle control ECU connector.


h.

Connect the accelerator pedal sensor assembly connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR