Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  Pattern Select Switch Eco Mode Circuit  


DESCRIPTION

When selecting ECO drive mode, the ECO mode switch (eco switch assembly) operation signal is sent to the air conditioning amplifier assembly. Following this, ECO drive mode control is activated for the heater and air conditioning system.

WIRING DIAGRAM

A254642E56
4.5,3.74 4.823,3.948 0.323,0.208 10 false G34 5.146,2.833 5.667,3.021 0.521,0.188 10 false ECOS 4.958,2.74 5.208,2.948 0.25,0.208 10 false 4 1.146,3.344 1.531,3.521 0.385,0.177 10 false G62 1.823,2.729 2.063,2.896 0.24,0.167 10 false E 1.656,2.729 1.802,2.917 0.146,0.188 10 false 6 3.25,2.729 3.396,2.917 0.146,0.188 10 false 9 2.865,2.729 3.302,2.99 0.438,0.26 10 false ECU 0.594,4.396 2.469,4.625 1.875,0.229 10 false : CAN Communication 0.958,1.24 2.167,1.615 1.208,0.375 10 false Combination Meter assembly 2.719,1.219 4.625,1.615 1.906,0.396 10 false Hybrid Vehicle Control ECU 1.156,3.521 3.938,3.938 2.781,0.417 10 false ECO Mode Switch (Eco Switch Assembly) 4.51,3.906 6.875,4.198 2.365,0.292 10 false Air Conditioning Amplifier Assembly

PROCEDURE

2.CHECK DTC OUTPUT (ALL CODES)

A

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INDICAT. ECO MODE)

B

GO TO DTC CHART

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INDICAT. ECO MODE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Body / Combination Meter / Active Test / Indicat. ECO Mode.


d.

Perform the "Indicat. ECO MODE" Active Test.

OK:

The ECO mode indicator light comes on or blinks.



e.

Turn the power switch off.



OK

4.READ VALUE USING INTELLIGENT TESTER (ECO MODE)

NG

REPLACE COMBINATION METER ASSEMBLY

4.READ VALUE USING INTELLIGENT TESTER (ECO MODE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / ECO Mode.


d.

Read the value displayed on the intelligent tester.

Tester Display Measurement Item/Range Normal Condition
ECO Mode ECO drive mode transition availability/
ON or OFF
In ECO drive mode: ON

Result:
Result Proceed to
The intelligent tester display changes according to the ECO mode switch (eco switch assembly) operation. A
The intelligent tester display does not changes according to the ECO mode switch (eco switch assembly) operation. B




A

B

5.READ VALUE USING INTELLIGENT TESTER (ECO SWITCH)
5.READ VALUE USING INTELLIGENT TESTER (ECO SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Body / Air Conditioning / Data List / ECO Switch.


d.

Read the value displayed on the intelligent tester.

Tester Display Measurement Item/Range Normal Condition
ECO Switch ECO mode switch (eco switch assembly) condition/
ON or OFF
ECO mode switch (eco switch assembly) being pushed and held: ON
ECO mode switch (eco switch assembly) not pushed: OFF

Result:
Result Proceed to
The intelligent tester display changes according to the ECO mode switch (eco switch assembly) operation. A
The intelligent tester display does not changes according to the ECO mode switch (eco switch assembly) operation. B




A

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

B

6.INSPECT ECO MODE SWITCH (ECO SWITCH ASSEMBLY)
6.INSPECT ECO MODE SWITCH (ECO SWITCH ASSEMBLY)
a.

Remove the ECO mode switch (eco switch assembly) (See page Vehicle Interior>HEATING / AIR CONDITIONING>ECO SWITCH>COMPONENTS).


b.
U158945E01
0.58,1.022 0.887,1.184 0.307,0.163 10 G62 2.256,1.752 2.375,1.915 0.119,0.163 10 E 0.248,0.222 0.429,0.385 0.181,0.163 10 *a 2.295,1.734 2.025,1.361 false 1.093,1.752 1.410,1.915 0.317,0.163 10 ECU 1.305,1.734 1.574,1.361 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G62-9 (ECU) - G62-6 (E) ECO mode switch (eco switch assembly) being pushed and held Below 1 Ω
ECO mode switch (eco switch assembly) not pushed 10 kΩ or higher



Text in Illustration
*a Component without harness connected
(ECO Mode Switch (Eco Switch Assembly))

c.

Install the ECO mode switch (eco switch assembly).



OK

7.CHECK HARNESS AND CONNECTOR (ECO MODE SWITCH (ECO SWITCH ASSEMBLY) - BODY GROUND)

NG

REPLACE ECO MODE SWITCH (ECO SWITCH ASSEMBLY)

7.CHECK HARNESS AND CONNECTOR (ECO MODE SWITCH (ECO SWITCH ASSEMBLY) - BODY GROUND)
a.

Disconnect connector G62 from the ECO mode switch (eco switch assembly).


b.
U158946E01
0.592,1.079 0.886,1.242 0.295,0.163 10 G62 1.018,1.809 1.137,1.972 0.119,0.163 10 E 0.345,0.245 0.527,0.408 0.181,0.163 10 *a 1.104,1.787 1.402,1.34 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G62-6 (E) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to ECO Mode Switch (Eco Switch Assembly))

c.

Connect the ECO mode switch (eco switch assembly) connector.



OK

8.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - ECO MODE SWITCH (ECO SWITCH ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - ECO MODE SWITCH (ECO SWITCH ASSEMBLY))
a.

Disconnect connector G34 from the air conditioning amplifier assembly.


b.

Disconnect connector G62 from the ECO mode switch (eco switch assembly).


c.
U158962E01
0.693,3.367 0.986,3.530 0.293,0.163 10 G62 1.951,4.132 2.271,4.295 0.320,0.163 10 ECU 0.352,2.568 0.534,2.730 0.181,0.163 10 *b 0.1,0.035 0.282,0.198 0.181,0.163 10 *a 2.114,4.109 1.879,3.662 false 1.023,1.567 1.327,1.730 0.304,0.163 10 G34 1.424,2.141 1.836,2.304 0.413,0.163 10 ECOS 1.699,2.118 1.871,1.671 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G34-4 (ECOS) - G62-9 (ECU) Always Below 1 Ω
G34-4 (ECOS) or G62-9 (ECU) - Body ground Always 10 kΩ or higher



Text in Illustration
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)
*b Front view of wire harness connector
(to ECO Mode Switch (Eco Switch Assembly))

d.

Connect the ECO mode switch (eco switch assembly) connector.


e.

Connect the air conditioning amplifier assembly connector.



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR