Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2014.12–2015.11
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0069-273  Manifold Absolute Pressure - Barometric Pressure Correlation  


DESCRIPTION

The atmospheric pressure sensor mounted on the MG ECU circuit board detects the atmospheric pressure. This reading is used to perform system control that considers vehicle usage conditions.

A379089E05
0.781,0.76 3.125,1.292 2.344,0.531 10 false Hybrid Vehicle Control ECU 1.542,2.292 2.323,2.646 0.781,0.354 10 false ECM 0.792,3.146 2.323,3.438 1.531,0.292 10 false CAN Communication 0.781,3.448 2.344,3.74 1.563,0.292 10 false Serial Communication 4.438,0.135 6.594,0.531 2.156,0.396 10 false Inverter With Converter Assembly 4.448,0.542 6.438,1.052 1.99,0.51 10 false MG ECU (Atmosphere Pressure Sensor) 4.542,1.229 6.521,1.594 1.979,0.365 10 false Atmosphere Pressure Sensor 4.229,1.99 6.438,2.76 2.208,0.771 10 false Manifold Absolute Pressure Sensor Assembly (Intake Air Surge Tank Assembly)

DTC No. INF Code DTC Detection Condition Trouble Area
P0069 273 Difference between the atmospheric pressure value of the atmospheric pressure sensor in the inverter with converter assembly and the manifold absolute pressure sensor (for EGR control) exceeds a specified value. The same condition recurs within 3 hours when driving in EV mode.
·

Inverter with converter assembly

·

Manifold absolute pressure sensor

·

ECM

·

Wire harness or connector



WIRING DIAGRAM

A259008E21
0.135,2.625 0.448,2.823 0.313,0.198 10 false C15 0.135,2.792 2.396,3.063 2.26,0.271 10 false Manifold Absolute Pressure Sensor 6.073,3.375 6.469,3.698 0.396,0.323 10 false ECM 5.792,3.083 6.365,3.292 0.573,0.208 10 false C9*2 5.302,0.99 5.573,1.135 0.271,0.146 10 false 118 5.365,1.552 5.552,1.719 0.188,0.167 10 false 87 5.302,2.094 5.594,2.24 0.292,0.146 10 false 119 5.625,1.563 6.167,1.938 0.542,0.375 10 false PIM 5.625,2.104 6.052,2.448 0.427,0.344 10 false EPIM 1.365,0.99 1.948,1.198 0.583,0.208 10 false VC 1.323,1.552 2.104,1.885 0.781,0.333 10 false PIM 1.385,2.094 1.896,2.375 0.51,0.281 10 false E2 1.677,0.99 1.958,1.313 0.281,0.323 10 false 3 1.667,1.552 2.031,1.76 0.365,0.208 10 false 1 1.677,2.094 1.875,2.281 0.198,0.188 10 false 2 5.625,0.979 6.083,1.292 0.458,0.313 10 false VCPM 0.281,3.24 1.469,3.802 1.188,0.563 10 false *1: LHD 1.083,3.24 2.271,3.802 1.188,0.563 10 false *2: RHD 5.792,3.229 6.458,3.427 0.667,0.198 10 false C10*1

CAUTION / NOTICE / HINT

HINT:

After the repair, perform the following procedure to confirm the repair.

1.

If the values of Data List items "Atmosphere Pressure" and "MAP" are almost the same with the engine stopped and the power switch on (IG), the vehicle is normal.



PROCEDURE

1.CHECK DTC OUTPUT (ENGINE AND ECT)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (READY).


c.

Fully depress the accelerator pedal for 5 seconds to start the engine and keep it running.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Check if DTCs are output.

Result:
Result Proceed to
DTCs other than those listed in the following table are output. A
Any of the following DTCs are also output. B


DTC No. Relevant Diagnosis
P0107 Manifold Absolute Pressure / Barometric Pressure Circuit Low Input
P0108 Manifold Absolute Pressure / Barometric Pressure Circuit High Input

HINT:

P0069-273 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.



f.

Turn the power switch off.



A

2.CHECK DTC OUTPUT (HYBRID CONTROL)

B

2.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
P0069-273 only is output. A
Any of the following DTCs are also output. B


DTC No. Relevant Diagnosis
P0A1A-151, 658, Generator Control Module
P0A1B-786 Drive Motor "A" Control Module
P0A1D-148 Hybrid Powertrain Control Module
P1C2A-155 Generator A/D Converter Circuit
P1C73-512 Sensor Standard Voltage "F" Circuit / Open
P1CA6-156 Generator Control Module Malfunction
P1CA7-193 Drive Motor Control Module Malfunction
P2228-268 Barometric Pressure Sensor "A" Circuit Low
P2229-269 Barometric Pressure Sensor "A" Circuit High
P2511-149 ECM/PCM Power Relay Sensor Circuit Intermittent
P3133-659 Communication Error from Generator to Drive Motor "A"
P3134-661 Communication Error from Drive Motor "A" to Generator
P324E-788 MG-ECU Power Relay Intermittent Circuit
U0100-211, 530 Lost Communication with ECM/PCM "A"
U0110 (all INF codes)*1 Lost Communication with Drive Motor Control Module "A"

HINT:
·

*1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.

·

P0069-273 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.




e.

Turn the power switch off.



A

3.READ VALUE USING INTELLIGENT TESTER (MAP, ATMOSPHERE PRESSURE)

B

3.READ VALUE USING INTELLIGENT TESTER (MAP, ATMOSPHERE PRESSURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / MAP, Atmosphere Pressure.


d.

Using the table, read the normal atmospheric pressure value for the applicable altitude.

A250945


e.

Compare the MAP and Atmosphere Pressure values in the Data List with the normal atmospheric value from the table.

Result:
Result Proceed to
Other than the following. A
Difference between MAP in Data List and normal atmospheric pressure value is 10 kPa or more. B
Difference between Atmosphere Pressure in Data List and normal atmospheric pressure value is 10 kPa or more. C



f.

Turn the power switch off.



A

4.READ VALUE USING INTELLIGENT TESTER (MAP)

B

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)

C

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

4.READ VALUE USING INTELLIGENT TESTER (MAP)
a.

Move the shift lever to P.


b.

Connect the intelligent tester to the DLC3.


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / MAP


d.

Read the MAP value in the Data List with the engine stopped.


e.

While depressing the brake pedal, turn the power switch on (READY).


f.

With the READY indicator light illuminated, fully depress the accelerator pedal.


g.

Read the MAP value in the Data List with the engine running.


h.

Compare the MAP value noted with the engine stopped and the MAP value noted with the engine running.

OK:

The MAP value changes (pressure decreases when the engine is started).



i.

Turn the power switch off.



OK

5.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)
5.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

(See page xxx)


NEXT

6.READ VALUE USING INTELLIGENT TESTER (MAP, ATMOSPHERE PESSURE)
6.READ VALUE USING INTELLIGENT TESTER (MAP, ATMOSPHERE PESSURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / MAP, Atmosphere Pressure.


d.

Compare the Data List item "MAP" with "Atmosphere Pressure".

Result:
Result Proceed to
The difference between "MAP" and "Atmosphere Pressure" is 10 kPa or more. A
The difference between "MAP" and "Atmosphere Pressure" is less than 10 kPa. B



e.

Turn the power switch off.



A

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

B

COMPLETED

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)

OK

8.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

11.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
8.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NEXT

9.CLEAR DTC
9.CLEAR DTC
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Clear DTCs and freeze frame data.


e.

Turn the power switch off.



NEXT

10.CHECK DTC OUTPUT (HYBRID CONTROL)
10.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
P0069-273 is not output. A
P0069-273 is output again. B



e.

Turn the power switch off.



A

COMPLETED

B

11.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR