The atmospheric pressure sensor mounted on the MG ECU circuit board detects the atmospheric pressure. This reading is used to perform system control that considers vehicle usage conditions.
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| P0069 | 273 | Difference between the atmospheric pressure value of the atmospheric pressure sensor in the inverter with converter assembly and the manifold absolute pressure sensor (for EGR control) exceeds a specified value. The same condition recurs within 3 hours when driving in EV mode. | ·
Inverter with converter assembly ·
Manifold absolute pressure sensor ·
ECM ·
Wire harness or connector |
After the repair, perform the following procedure to confirm the repair.
If the values of Data List items "Atmosphere Pressure" and "MAP" are almost the same with the engine stopped and the power switch on (IG), the vehicle is normal.
Connect the intelligent tester to the DLC3.
Turn the power switch on (READY).
Fully depress the accelerator pedal for 5 seconds to start the engine and keep it running.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs other than those listed in the following table are output. | A |
| Any of the following DTCs are also output. | B |
| DTC No. | Relevant Diagnosis |
|---|---|
| P0107 | Manifold Absolute Pressure / Barometric Pressure Circuit Low Input |
| P0108 | Manifold Absolute Pressure / Barometric Pressure Circuit High Input |
P0069-273 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.
Turn the power switch off.
A
B
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / DTC.
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| P0069-273 only is output. | A |
| Any of the following DTCs are also output. | B |
| DTC No. | Relevant Diagnosis |
|---|---|
| P0A1A-151, 658, | Generator Control Module |
| P0A1B-786 | Drive Motor "A" Control Module |
| P0A1D-148 | Hybrid Powertrain Control Module |
| P1C2A-155 | Generator A/D Converter Circuit |
| P1C73-512 | Sensor Standard Voltage "F" Circuit / Open |
| P1CA6-156 | Generator Control Module Malfunction |
| P1CA7-193 | Drive Motor Control Module Malfunction |
| P2228-268 | Barometric Pressure Sensor "A" Circuit Low |
| P2229-269 | Barometric Pressure Sensor "A" Circuit High |
| P2511-149 | ECM/PCM Power Relay Sensor Circuit Intermittent |
| P3133-659 | Communication Error from Generator to Drive Motor "A" |
| P3134-661 | Communication Error from Drive Motor "A" to Generator |
| P324E-788 | MG-ECU Power Relay Intermittent Circuit |
| U0100-211, 530 | Lost Communication with ECM/PCM "A" |
| U0110 (all INF codes)*1 | Lost Communication with Drive Motor Control Module "A" |
*1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.
P0069-273 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.
Turn the power switch off.
A
B
(See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART)
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / MAP, Atmosphere Pressure.
Using the table, read the normal atmospheric pressure value for the applicable altitude.
Compare the MAP and Atmosphere Pressure values in the Data List with the normal atmospheric value from the table.
| Result | Proceed to |
|---|---|
| Other than the following. | A |
| Difference between MAP in Data List and normal atmospheric pressure value is 10 kPa or more. | B |
| Difference between Atmosphere Pressure in Data List and normal atmospheric pressure value is 10 kPa or more. | C |
Turn the power switch off.
A
B
C
Move the shift lever to P.
Connect the intelligent tester to the DLC3.
Enter the following menus: Powertrain / Hybrid Control / Data List / MAP
Read the MAP value in the Data List with the engine stopped.
While depressing the brake pedal, turn the power switch on (READY).
With the READY indicator light illuminated, fully depress the accelerator pedal.
Read the MAP value in the Data List with the engine running.
Compare the MAP value noted with the engine stopped and the MAP value noted with the engine running.
The MAP value changes (pressure decreases when the engine is started).
Turn the power switch off.
OK
NG
NEXT
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / MAP, Atmosphere Pressure.
Compare the Data List item "MAP" with "Atmosphere Pressure".
| Result | Proceed to |
|---|---|
| The difference between "MAP" and "Atmosphere Pressure" is 10 kPa or more. | A |
| The difference between "MAP" and "Atmosphere Pressure" is less than 10 kPa. | B |
Turn the power switch off.
A
B
OK
NG
NEXT
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / DTC.
Clear DTCs and freeze frame data.
Turn the power switch off.
NEXT
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / DTC.
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| P0069-273 is not output. | A |
| P0069-273 is output again. | B |
Turn the power switch off.
A
B
OK
NG