Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0AFC-150  Hybrid Battery Pack Sensor Module  


DESCRIPTION

The power management control ECU alerts the driver and performs fail-safe control based on error signals sent from the battery smart unit.

DTC NO. INF Code DTC Detection Condition Trouble Area
P0AFC 150 Power source voltage of the battery smart unit drops during precharge.
·

Battery smart unit

·

Wire harness or connector



WIRING DIAGRAM

A279685E10
5.302,3.479 6.51,3.688 1.208,0.208 10 false Battery Smart Unit 2.292,0.906 2.719,1.125 0.427,0.219 10 false IGCT 4.573,0.438 5.521,0.635 0.948,0.198 10 false IGCT NO. 4 4.354,1.104 5.302,1.302 0.948,0.198 10 false IGCT NO. 2 0.635,2.656 1.667,2.854 1.031,0.198 10 false Auxiliary Battery 2.698,1.292 3.135,1.438 0.438,0.146 10 false MREL 2.708,2.365 3.146,2.51 0.438,0.146 10 false BTH+ 2.708,2.688 3.146,2.833 0.438,0.146 10 false BTH- 3.156,1.281 3.458,1.427 0.302,0.146 10 false A39 3.219,2.198 3.521,2.344 0.302,0.146 10 false 32 3.146,2.354 3.469,2.5 0.323,0.146 10 false G57 5.667,2.354 6.042,2.5 0.375,0.146 10 false BTH+ 5.667,2.698 6.042,2.844 0.375,0.146 10 false BTH- 5.49,2.229 5.677,2.396 0.188,0.167 10 false 1 5.667,0.292 6.104,0.469 0.438,0.177 10 false IGCT 2.781,0.156 3,0.323 0.219,0.167 10 false 5 2.063,0.156 2.26,0.313 0.198,0.156 10 false 3 2.063,0.521 2.271,0.667 0.208,0.146 10 false 2 2.781,0.521 2.979,0.698 0.198,0.177 10 false 1 4.719,0.198 4.833,0.354 0.115,0.156 10 false 1 5.125,0.198 5.271,0.375 0.146,0.177 10 false 2 5.667,3.01 6.042,3.156 0.375,0.146 10 false GND 5.49,2.896 5.667,3.104 0.177,0.208 10 false 6 0.5,0.844 1.281,1.063 0.781,0.219 10 false IGCT-MAIN 0.531,1.958 1.313,2.177 0.781,0.219 10 false MAIN 3.24,1.125 3.438,1.302 0.198,0.177 10 false 6 3.146,2.688 3.438,2.833 0.292,0.146 10 false G57 3.219,2.531 3.406,2.677 0.188,0.146 10 false 33 5.49,2.594 5.677,2.76 0.188,0.167 10 false 4 5.469,0.198 5.615,0.375 0.146,0.177 10 false 3 2.167,3.01 3.5,3.385 1.333,0.375 10 false Power Management Control ECU 5.302,3.333 5.688,3.552 0.385,0.219 10 false M39 2.823,1.646 3.146,1.844 0.323,0.198 10 false +B1 2.823,2 3.177,2.198 0.354,0.198 10 false +B2 3.25,1.49 3.448,1.667 0.198,0.177 10 false 5 3.24,1.823 3.438,2 0.198,0.177 10 false 2 3.156,1.656 3.458,1.802 0.302,0.146 10 false A39 3.146,2 3.448,2.146 0.302,0.146 10 false A38 4.104,0.948 4.219,1.104 0.115,0.156 10 false 1 4.104,1.292 4.25,1.469 0.146,0.177 10 false 2 0.281,1.052 0.396,1.208 0.115,0.156 10 false 1 0.292,0.635 0.438,0.813 0.146,0.177 10 false 2

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

After completing repairs, restart the system (turn the power switch on (READY)) and recheck for DTCs (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR).

·

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

(a)

Turn the power switch on (READY) and wait for 15 seconds or more.




PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IGCT VOLTAGE)

OK

NG

2.CHECK HARNESS AND CONNECTOR (GND - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (GND - BODY GROUND)

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATT VL SSR FUSE - BATTERY SMART UNIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND - BODY GROUND)