Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0C76-523  Hybrid Battery System Discharge Time Too Long  


DESCRIPTION

Refer to the description for DTC P0A78-266 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A78-266).

DTC No. INF Code DTC Detection Condition Trouble Area
P0C76 523 Inverter voltage (VH) sensor offset malfunction
·

Inverter with converter assembly

·

Wire harness or connector

·

Power management control ECU



HINT:

When the power switch is turned off, the MG ECU applies current to MG2 in a way that does not generate torque, in order to discharge the residual voltage in the inverter. When the hybrid system is normal, the VH value is almost 0 V after discharge. This DTC will be stored if the VH value is more than the specified value after discharge.


A111758E02
2.031,0.7 2.212,0.855 0.181,0.154 10 IG 2.631,0.585 2.869,0.739 0.238,0.154 10 ON 3.066,0.805 3.371,0.959 0.305,0.154 10 OFF 1.997,1.338 2.212,1.492 0.214,0.154 10 VH 3.776,1.361 4.415,1.528 0.639,0.167 10 Abnormal 3.209,2.344 4.307,2.512 1.098,0.167 10 During Discharge 4.398,1.759 4.890,1.926 0.492,0.167 10 Normal 3.618,1.514 3.734,1.435 false 3.909,2.036 4.358,1.853 false

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).

Refer to the wiring diagram for DTC P321E-318 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P321E-318).

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch off and wait for 30 seconds or more.

2.

Turn the power switch on (READY) and wait for 30 seconds or more.

3.

Turn the power switch off and wait for 30 seconds or more.



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
Only P0C76-523 is output or P0C76-523 and DTCs other than the ones in the table below are also output. A
Any of the following DTCs are also output. B


DTC No. Relevant Diagnosis
P0A1A-151, 155, 156, 200, 658, 659, 791, 792, 793 Generator Control Module
P0A1B-163, 164, 168, 193, 511, 661, 786, 794, 795, 796 Drive Motor "A" Control Module
P0A1D-148 Hybrid Powertrain Control Module
P0A3F-243 Drive Motor "A" Position Sensor Circuit
P0A40-500 Drive Motor "A" Position Sensor Circuit Range/Performance
P0A41-245 Drive Motor "A" Position Sensor Circuit Low
P0A4B-253 Generator Position Sensor Circuit
P0A4C-513 Generator Position Sensor Circuit Range/Performance
P0A4D-255 Generator Position Sensor Circuit Low
P0A78-266, 267 Drive Motor "A" Inverter Performance
P0ADC-226 Hybrid Battery Positive Contactor Control Circuit High
P0AE0-228 Hybrid Battery Negative Contactor Control Circuit High
P0AE7-224 Hybrid Battery Precharge Contactor Control Circuit High
P2511-149 ECM/PCM Power Relay Sensor Circuit Intermittent
P324E-788 MG-ECU Power Relay Intermittent Circuit
U0110 (all INF codes)*1 Lost Communication with Drive Motor Control Module "A"

HINT:
·

*1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.

·

P0C76-523 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.




e.

Turn the power switch off.



A

2.CHECK DTC OUTPUT (HYBRID CONTROL)

B

2.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
Any of the following DTCs are also output. A
Only P0C76-523 is output or P0C76-523 and DTCs other than the ones in the table below are also output. B


DTC No. Relevant Diagnosis
P0A78-306 Drive Motor "A" Inverter Performance
P0A7A-344 Generator Inverter Performance
P0A90-251, 509 Drive Motor "A" Performance
P0A92-261, 521 Hybrid Generator Performance

HINT:

When the DTCs listed in the table above are also output, there may be a short between the HSDN (MG shut down signal) circuit and power circuit.



e.

Turn the power switch off.



A

3.CHECK POWER MANAGEMENT CONTROL ECU

B

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

3.CHECK POWER MANAGEMENT CONTROL ECU
a.

Turn the power switch on (IG).


b.
U183267E02
1.521,1.917 1.125,2.438 false 1.823,1.708 2.198,2.448 false 0.271,0.208 0.438,0.365 0.167,0.156 10 false *a 1.24,2.615 1.51,2.781 0.271,0.167 10 false A39 1.917,2.625 2.25,2.792 0.333,0.167 10 false G57 0.698,2.365 1.115,2.51 0.417,0.146 10 false HSDN 2.25,2.406 2.667,2.552 0.417,0.146 10 false E1

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A39-31 (HSDN) - G57-6 (E1) Power switch on (IG) Below 4.5 V


Text in Illustration
*a Component with harness connected
(Power Management Control ECU)


c.

Turn the power switch off.



OK

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

NG

4.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - POWER MANAGEMENT CONTROL ECU)
4.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - POWER MANAGEMENT CONTROL ECU)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector A47 from the inverter with converter assembly.


c.

Disconnect connector A39 from the power management control ECU.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.
A379052E04
0.25,0.917 0.667,1.167 0.417,0.25 0.833,1.833 1.375,1.271 false 2.135,1.021 2.469,0.448 false 2.271,1.021 2.813,0.698 false 0.073,0.104 0.385,0.302 0.313,0.198 10 false *a 0.333,0.958 0.75,1.188 0.417,0.229 10 false A47 0.615,1.865 1.083,2.073 0.469,0.208 10 false HSDN 2.5,0.323 2.875,0.521 0.375,0.198 10 false +B2 2.854,0.583 3.135,0.781 0.281,0.198 10 false +B

A379053E08
0.469,1.865 0.885,2.115 0.417,0.25 1.594,2.104 1.875,1.958 false 1.74,2.51 1.531,2.302 false 1.938,2.292 1.656,2.104 false 1.188,2.75 1.333,2.094 false 0.906,2.5 1.26,2.104 false 0.115,0.094 0.427,0.292 0.313,0.198 10 false *b 0.698,2.51 1.24,2.719 0.542,0.208 10 false MREL 1.969,2.208 2.51,2.417 0.542,0.208 10 false IG2 0.563,1.906 1.104,2.115 0.542,0.208 10 false A39 1.927,1.865 2.469,2.073 0.542,0.208 10 false IG2D 1.635,2.531 2.177,2.74 0.542,0.208 10 false HSDN 1.042,2.771 1.583,2.979 0.542,0.208 10 false +B1

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A47-31 (HSDN) or A39-31 (HSDN) - Body ground Power switch on (IG) Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
*b Rear view of wire harness connector
(to Power Management Control ECU)

NOTICE:

Turning the power switch on (IG) with the connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A39-31 (HSDN) - A39-1 (IG2) Power switch off 10 kΩ or higher
A39-31 (HSDN) - A39-2 (IG2D) Power switch off 10 kΩ or higher
A39-31 (HSDN) - A39-5 (+B1) Power switch off 10 kΩ or higher
A39-31 (HSDN) - A39-6 (MREL) Power switch off 10 kΩ or higher
A47-31 (HSDN) - A47-10 (+B) Power switch off 10 kΩ or higher
A47-31 (HSDN) - A47-9 (+B2) Power switch off 10 kΩ or higher



j.

Connect the inverter with converter assembly connector.


k.

Connect the power management control ECU connector.



OK

5.CHECK INVERTER WITH CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK INVERTER WITH CONVERTER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector A47 from the inverter with converter assembly.


c.
U158861E02
1.781,1.25 2.281,1.865 false 1.115,1.021 0.573,0.667 false 1.281,1.042 0.781,1.875 false 2.125,1.865 2.563,2.021 0.438,0.156 10 false HSDN 0.115,0.063 0.271,0.219 0.156,0.156 10 false *a 0.292,0.573 0.531,0.729 0.24,0.156 10 false +B 0.573,1.896 0.885,2.052 0.313,0.156 10 false +B2 0.198,1.083 0.469,1.24 0.271,0.156 10 false A47

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A47-31 (HSDN) - A47-10 (+B) Power switch off 5 kΩ or higher
A47-31 (HSDN) - A47-9 (+B2) Power switch off 5 kΩ or higher


Text in Illustration
*a Component without harness connected
(Inverter with Converter Assembly)


d.

Connect the inverter with converter assembly connector.



OK

NG

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS