Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P324E-788  MG-ECU Power Relay Intermittent Circuit  


DESCRIPTION

If the MG ECU located in the inverter with converter assembly is reset due to a problem with the power source in the inverter, the hybrid vehicle control ECU will set this DTC.

DTC No. INF Code DTC Detection Condition Trouble Area
P324E 788 Error in reset signal from the inverter assembly power source IC
·

Wire harness or connector

·

Inverter with converter assembly

·

Hybrid vehicle control ECU



WIRING DIAGRAM

A254640E27
0.125,1.177 0.823,1.521 0.698,0.344 10 false to Auxiliary Battery 2.302,1.115 2.396,1.271 0.094,0.156 10 false 3 2.302,1.5 2.396,1.656 0.094,0.156 10 false 2 2.438,1.854 2.792,2.01 0.354,0.156 10 false IGCT 3.719,2.344 4.135,2.479 0.417,0.135 10 false MREL 3.583,3.281 3.854,3.417 0.271,0.135 10 false A72 3.583,3.427 4.521,3.74 0.938,0.313 10 false Hybrid Vehicle Control ECU 5.594,3.594 5.865,3.729 0.271,0.135 10 false A47 5.594,3.76 7.042,4.073 1.448,0.313 10 false Inverter with Converter Assembly 3.583,1.427 3.906,1.583 0.323,0.156 10 false PCU 2.833,1.115 2.927,1.271 0.094,0.156 10 false 5 3.438,1.115 3.531,1.271 0.094,0.156 10 false 1 3.969,1.115 4.063,1.271 0.094,0.156 10 false 2 2.833,1.5 2.927,1.656 0.094,0.156 10 false 1 3.583,2.229 3.677,2.385 0.094,0.156 10 false 6 5.729,1.219 5.927,1.354 0.198,0.135 10 false +B 5.469,1.115 5.646,1.271 0.177,0.156 10 false 10 5.729,1.896 6.01,2.031 0.281,0.135 10 false +B2 5.552,1.792 5.646,1.948 0.094,0.156 10 false 9 5.729,2.49 6.146,2.625 0.417,0.135 10 false GND1 5.469,2.385 5.646,2.542 0.177,0.156 10 false 28 5.729,3.177 6.146,3.313 0.417,0.135 10 false GND2 5.469,3.063 5.646,3.219 0.177,0.156 10 false 27

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (IG) and wait for 5 seconds or more.



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
P324E-788 only is output. A
U0110-159, 194, 197, 199, 230, 656, 657 are also output. B



e.

Turn the power switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

OK

3.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - IGCT RELAY)

NG

CONNECT SECURELY

3.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - IGCT RELAY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector A47 from the inverter with converter assembly.


c.

Remove the IGCT relay from the No. 2 engine room relay block and No. 2 junction block assembly.


d.

Measure the resistance according to the value(s) in the table below.

U158984E02
2.125,1.927 1.885,2.354 false 2.24,1.927 2.49,2.354 false 2.24,1.729 2.479,1.302 false 2.125,1.729 1.875,1.302 false 0.635,1.75 1,2.042 0.365,0.292 10 false A47 1.677,2.385 2.094,2.552 0.417,0.167 10 false GND2 2.406,2.385 2.813,2.552 0.406,0.167 10 false GND1 0.896,1.146 1.073,1.313 0.177,0.167 10 false *a 3.51,0.885 3.688,1.052 0.177,0.167 10 false *1 6.208,1.479 6.385,1.646 0.177,0.167 10 false *2 1.708,1.115 1.979,1.281 0.271,0.167 10 false +B2 2.469,1.115 2.667,1.281 0.198,0.167 10 false +B

Text in Illustration
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly *2 IGCT Relay
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
- -

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
A47-10 (+B) - 5 (IGCT relay) Power switch off Below 1 Ω
A47-9 (+B2) - 5 (IGCT relay) Power switch off Below 1 Ω
A47-28 (GND1) - Body ground Power switch off Below 1 Ω
A47-27 (GND2) - Body ground Power switch off Below 1 Ω



e.

Install the IGCT relay.


f.

Connect the inverter with converter assembly connector.



OK

4.CHECK DTC OUTPUT (HYBRID CONTROL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
Only DTC P0A1A-151, P3133-659 or P324E-788 is output. A
Other than above. B



e.

Turn the power switch off.



A

5.CLEAR DTC

B

5.CLEAR DTC

NEXT

6.CHECK DTC OUTPUT (HYBRID CONTROL)
6.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch off and wait for 30 seconds or more.


c.

Turn the power switch on (IG) and wait for 5 seconds or more.


d.

Turn the power switch on (READY).


e.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


f.

Check if DTCs are output.

Result:
Result Proceed to
No DTCs are output (not including history DTCs). A
Only DTC P0A1A-151, P3133-659 or P324E-788 is output. B
Other than above. C



g.

Turn the power switch off.



A

REPLACE MG CONTROL COMPUTER

B

REPLACE POWER MODULE INTELLIGENT TRANSISTOR KIT AND MG CONTROL COMPUTER

C