Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P321E-318  All HV Gate Blocking Range/Performance  


DESCRIPTION

The hybrid vehicle control ECU sends a block signal to the motor generator control ECU (MG ECU) to shutdown the power supply to the motor. When the system is not in the on (READY) state, it sends an HSDN (MG shutdown signal) signal from the hybrid vehicle control ECU to the motor generator control ECU (MG ECU) to check the function of the HV gate block. When a malfunction is detected in the HV gate block function, DTCs are stored.

DTC No. INF Code DTC Detection Condition Trouble Area
P321E 318
·

An open or ground short in the HV gate block signal circuit when the gate is operating

·

When the HV gate block function is being checked, inverter voltage (VH) drops or current flows in the inverter. (Both the motor (MG2) and the generator (MG1) are malfunctioning.)


·

Wire harness or connector

·

Hybrid vehicle control ECU

·

Inverter with converter assembly



WIRING DIAGRAM

A279684E13
2.167,0.396 2.427,0.563 0.26,0.167 10 false +B 2.104,0.74 2.427,0.906 0.323,0.167 10 false +B2 1.958,1.083 2.406,1.25 0.448,0.167 10 false HSDN 1.958,1.448 2.406,1.615 0.448,0.167 10 false GND1 1.958,1.781 2.406,1.948 0.448,0.167 10 false GND2 2.406,0.333 2.667,0.5 0.26,0.167 10 false 10 2.406,0.677 2.667,0.844 0.26,0.167 10 false 9 2.406,1.083 2.667,1.25 0.26,0.167 10 false 31 2.406,1.385 2.667,1.552 0.26,0.167 10 false 28 2.406,1.719 2.667,1.885 0.26,0.167 10 false 27 4.521,0.99 4.781,1.156 0.26,0.167 10 false 12 4.802,1.01 5.25,1.177 0.448,0.167 10 false HSDN 0.448,2.344 2.552,2.542 2.104,0.198 10 false Inverter with Converter Assembly 5.948,0.385 6.208,0.552 0.26,0.167 10 false +B 0.448,2.188 0.74,2.354 0.292,0.167 10 false A47 4.729,2.323 6.833,2.521 2.104,0.198 10 false Hybrid Vehicle Control ECU 4.469,1.188 4.76,1.354 0.292,0.167 10 false A72 3.333,0.406 4.198,0.615 0.865,0.208 10 false to PCU Fuse 4.458,1.688 4.75,1.854 0.292,0.167 10 false G80 4.573,1.49 4.833,1.656 0.26,0.167 10 false 6 4.792,1.646 5.24,1.813 0.448,0.167 10 false E1

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Wait for 30 seconds or more with the vehicle stopped, the power switch on (READY) and the shift lever in P. Then turn the power switch off and wait for 60 seconds or more.



PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

OK

3.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - HYBRID VEHICLE CONTROL ECU)

NG

CONNECT SECURELY

3.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - HYBRID VEHICLE CONTROL ECU)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector A47 from the inverter with converter assembly.


c.

Disconnect connector A72 from the hybrid vehicle control ECU.


d.
A379052E05
0.25,0.917 0.667,1.167 0.417,0.25 0.833,1.833 1.375,1.271 false 0.073,0.104 0.385,0.302 0.313,0.198 10 false *a 0.333,0.958 0.75,1.188 0.417,0.229 10 false A47 0.615,1.865 1.083,2.073 0.469,0.208 10 false HSDN

A379053E11
0.5,2.01 0.917,2.26 0.417,0.25 1.865,2.688 1.49,2.167 false 0.115,0.094 0.427,0.292 0.313,0.198 10 false *b 0.583,2.052 1.125,2.26 0.542,0.208 10 false A72 1.698,2.708 2.24,2.917 0.542,0.208 10 false HSDN

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A47-31 (HSDN) or A72-12 (HSDN) - Body ground and other terminals Power switch off 10 kΩ or higher
A47-31 (HSDN) - A72-12 (HSDN) Power switch off Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
*b Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)


e.

Connect the hybrid vehicle control ECU connector.


f.

Connect the inverter with converter assembly connector.



OK

4.CHECK INVERTER WITH CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK INVERTER WITH CONVERTER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector A47 from the inverter with converter assembly.


c.
U158862E02
1.781,1.26 2.219,1.885 false 1.083,1.219 0.656,1.896 false 2.125,1.896 2.563,2.052 0.438,0.156 10 false HSDN 0.115,0.063 0.271,0.219 0.156,0.156 10 false *a 0.479,1.906 1,2.063 0.521,0.156 10 false GND1 0.198,1.083 0.469,1.24 0.271,0.156 10 false A47

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A47-31 (HSDN) - A47-28 (GND1) Power switch off 2.65 to 3.55 kΩ


Text in Illustration
*a Component without harness connected
(Inverter with Converter Assembly)


d.

Connect the inverter with converter assembly connector.



OK

NG

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS