Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P2511-149  HV CPU Power Relay Sense Circuit Intermittent No Continuity  


DESCRIPTION

This DTC indicates that the hybrid vehicle control ECU monitors the +B power source voltage to detect an instantaneous interruption.

DTC No. INF Code DTC Detection Condition Trouble Area
P2511 149 When the power switch is on (READY), the hybrid vehicle control ECU is reset.
·

Wire harness or connector

·

Hybrid vehicle control ECU



WIRING DIAGRAM

Refer to the wiring diagram for DTC P3110-223 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P3110-223).

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (READY) and wait for 30 seconds or more.

(If the DTC is not output, drive the vehicle on urban roads according to the freeze frame data item "Vehicle Spd" for approximately 5 minutes.)



PROCEDURE

1.CHECK AUXILIARY BATTERY TERMINAL
a.

Confirm whether the auxiliary battery terminals have been disconnected recently.

Result:
Result Proceed to
Terminals have been disconnected. A
Terminals have not been disconnected. B




A

2.CONFIRM THAT MASTER WARNING LIGHT

B

5.CHECK AUXILIARY BATTERY TERMINAL (CONTACT PROBLEM)
2.CONFIRM THAT MASTER WARNING LIGHT
a.

Turn the power switch on (READY) from off.


b.

Confirm that the master warning light illuminates.

Result:
Result Proceed to
Master warning light illuminates. A
Master warning light does not illuminates. B


HINT:

DTC P2511-149 may be stored after disconnecting and reconnecting the auxiliary battery terminals. If this happens, the DTC will not be output if the power switch is turned off and then on (READY) again. In this case, clear DTCs to complete the inspection.



c.

Turn the power switch off.



A

3.CLEAR DTC

B

END

3.CLEAR DTC
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Read and record the DTCs and freeze frame data.


e.

Clear the DTCs and freeze frame data.


f.

Turn the power switch off.



NEXT

4.CHECK DTC OUTPUT (HYBRID CONTROL)
4.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
DTC P2511-149 is output again. A
DTCs other than P2511-149 are also output. B



e.

Turn the power switch off.



A

5.CHECK AUXILIARY BATTERY TERMINAL (CONTACT PROBLEM)

B

5.CHECK AUXILIARY BATTERY TERMINAL (CONTACT PROBLEM)
a.

Check the connection of the auxiliary battery terminal.

OK:

The terminal is connected securely and there is no contact problem.




OK

6.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

NG

CONNECT SECURELY

6.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - IGCT RELAY)

NG

CONNECT SECURELY

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - IGCT RELAY)
a.

Remove the IGCT relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Disconnect connectors A71 and A72 from hybrid vehicle control ECU.

U183301E02
1.51,1.719 1.615,2.188 false 1.885,1.719 2.104,2.198 false 0.354,0.177 0.542,0.396 0.188,0.219 10 false *a 4.01,0.177 4.198,0.396 0.188,0.219 10 false *1 5.865,0.333 6.052,0.552 0.188,0.219 10 false *2 1.5,2.198 1.802,2.396 0.302,0.198 10 false +B2 2.01,2.219 2.313,2.417 0.302,0.198 10 false +B1 1.229,2.469 1.5,2.635 0.271,0.167 10 false A71 1.833,2.469 2.104,2.635 0.271,0.167 10 false A72

Text in Illustration
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly *2 IGCT Relay
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A72-4 (+B1) - 5 (IGCT relay) Power switch off Below 1 Ω
A71-1 (+B2) - 5 (IGCT relay) Power switch off Below 1 Ω



d.

Install the IGCT relay.


e.

Connect the hybrid vehicle control ECU connectors.



OK

8.CHECK FOR INTERMITTENT PROBLEMS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK FOR INTERMITTENT PROBLEMS
a.

Check for intermittent problems (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).

i.

Check the connection and terminal contact pressure of connectors and wire harnesses between the hybrid vehicle control ECU and the No. 2 engine room relay block and No. 2 junction block assembly.


ii.

When the power switch is on (READY), jiggle the connectors and wire harnesses between the hybrid vehicle control ECU and the No. 2 engine room relay block and No. 2 junction block assembly.

Result:
Result Proceed to
Problem symptom does not recur. A
Problem symptom recurs. B





A

B

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA