Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P3000-388  Battery Control System  


DESCRIPTION

The power management control ECU alerts the driver and performs fail-safe control based on error signals received from the battery smart unit. This DTC is set when the SOC (state of charge) of the HV battery starts to drop as a result of leaving the shift lever in N, running out of fuel, or a malfunction in the hybrid control system.

DTC No. INF Code DTC Detection Condition Trouble Area
P3000 388 Discharge inhibition control malfunction
·

Fuel level

·

HV battery



CAUTION / NOTICE / HINT

HINT:
·

If the vehicle is stopped or parked with the shift lever in the N position for a long time, DTC P3000-388 may be set because the HV battery cannot be charged.

·

When the engine cannot be started, DTC P3000-388 may be set because the HV battery cannot be charged.

·

Repeated engine start checks may cause the SOC to drop, resulting in DTC P3000-388 being set. In this case, charge the HV battery using the THS charger.

·

Cranking the engine once causes the SOC to drop approximately 1%.

·

Charging the HV battery once (10 minutes) using the THS charger restores the SOC approximately 2%.

·

Charging the HV battery using the THS charger takes approximately 10 minutes when the battery temperature is 25°C (77°F) or approximately 30 minutes when the battery temperature is 0°C (32°F).

·

The THS charger is a supplemental charging device that enables the engine to start (READY-on state).

·

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

(a)

Turn the power switch on (READY) with the shift lever in P and decrease the SOC. While the battery is being discharged, check that the engine starts to charge the battery, and "State of Charge (All Bat)" increases and remains in the appropriate range.




PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
P3000-388 or P3000-389 only is output. A
DTCs other than P3000-388, P3000-389, and P0AF8 are also output. B



e.

Turn the power switch off.



A

2.CHECK DTC OUTPUT (ENGINE AND ECT)

B

2.CHECK DTC OUTPUT (ENGINE AND ECT)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
NO DTCs are output. A
DTCs are output. B



e.

Turn the power switch off.



A

3.CHECK AMOUNT OF FUEL

B

3.CHECK AMOUNT OF FUEL
a.

Turn the power switch on (IG).


b.

Check the amount of fuel by referring to the fuel gauge in the meter.

Result:
Result Proceed to
Proper amount of fuel is in the tank. A
There is no fuel in the tank. B



HINT:

Add fuel until the low fuel level warning light turns off.


c.

Turn the power switch off.



A

4.CHECK FREEZE FRAME DATA

B

REFUEL VEHICLE

4.CHECK FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Read the freeze frame data item "Shift Sensor Shift Pos" of DTC P3000-388.

NOTICE:
·

When the freeze frame data "Shift Sensor Shift Pos" was N, DTC P3000-388 may be stored due to the vehicle was left with shift lever in N and the HV battery could not be charged.

·

If DTC "P3000-388" only is output, charge the HV battery without replacing the HV battery.




e.

Turn the power switch off.



NEXT

5.CHECK ENGINE START
5.CHECK ENGINE START
a.

Turn the power switch on (READY).


b.

Check if the engine starts.

HINT:
·

Depressing the accelerator pedal with the shift lever in P will cause the engine to start.

·

Turning the power switch on (READY) and off repeatedly while the SOC is low may cause the SOC to drop further, resulting in DTC P3000-389 being set. Charge the HV battery using the THS charger as necessary.

·

Cranking the engine once causes the SOC to drop approximately 1%.

·

Charging the HV battery once (10 minutes) using the THS charger restores the SOC approximately 2%.



Result:
Result Proceed to
The engine starts. A
The engine does not start. B



c.

If the engine does not start, turn the power switch off.



A

LEAVE VEHICLE WITH SHIFT LEVER IN P, AND CHARGE HV BATTERY BY IDLING UNTIL IDLING STOPS

B

6.CLEAR DTC