Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P3000-603  Battery Control System  


DESCRIPTION

The power management control ECU monitors its internal operation and detects the following malfunction.

DTC No. INF Code DTC Detection Condition Trouble Area
P3000 603 The power management control ECU detects a HV battery cooling system error signal.
·

Power management control ECU

·

HV battery

·

Battery smart unit



Related Data List
DTC No. Data List
P3000-603
·

Temp of Batt TB1 to TB3

·

Inhaling Air Temp

·

Ambient Temperature

·

Power Resource IB

·

State of Charge (All Bat)

·

Cooling Fan Mode1

·

Cooling Fan 0

·

Hot Temperature Time



The following items can be helpful when performing repairs:

Data List
·

Vehicle Spd

·

Engine Run Time

·

Ready Signal


CAUTION / NOTICE / HINT

CAUTION:

When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Drive the vehicle for approximately 10 minutes according to the freeze frame data items "Vehicle Spd", "Temp of Batt TB1 to TB3", "Inhaling Air Temp", "Ambient Temperature" and "Power Resource IB".



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
P3000-603 only is output. A
DTCs other than P3000-603 are also output. B



e.

Turn the power switch off.



A

2.CLEAN BATTERY COOLING BLOWER FILTER

B

2.CLEAN BATTERY COOLING BLOWER FILTER
a.
A266553C09
2.052,1.906 1.802,1.906 1.802,1.906 1.698,1.333 false 2.094,1.854 2.396,2.083 0.302,0.229 10 false *a
*a Intake Port


Check the HV battery cooling system intake port for blockage.

HINT:

If anything is blocking the HV battery cooling system intake port, remove it.



b.

Clean the battery cooling blower filter.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>INSPECTION



NEXT

3.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
3.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Read the freeze frame data of DTC P3000-603.

NOTICE:
A408998C02
0.052,0.042 3.115,0.24 3.063,0.198 10 false Freeze Frame Data Recording Example 0.458,1.344 0.771,1.542 0.313,0.198 10 false *a 1.24,1.375 1.552,1.573 0.313,0.198 10 false *a 2.104,1.365 2.417,1.563 0.313,0.198 10 false *a 2.917,1.365 3.229,1.563 0.313,0.198 10 false *a 2.5,0.417 2.813,0.615 0.313,0.198 10 false *b 2.625,1.865 2.938,2.063 0.313,0.198 10 false *c
*a Freeze Frame Data Recorded
*b DTC Stored
*c Time


Although freeze frame data is recorded before and after a DTC is stored, for this step it is only necessary to read the freeze flame data recorded before "0s" (when the DTC was stored).



Result:
Result Proceed to
Other than below A
The sum of the value of each hybrid battery block voltage ("Battery Block Vol-V01 to V10") is less than the value of "VL-Voltage before Boosting" by 10 V or more. B


e.

Turn the power switch off.



A

4.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

B

7.REPLACE BATTERY SMART UNIT
4.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Read the freeze frame data of DTC P3000-603.

NOTICE:

Although freeze frame data is recorded before and after a DTC is stored, for this step it is only necessary to read the freeze flame data recorded at "0s" (when the DTC was stored).



Result:
Result Proceed to
Other than below A
The value of any of "Temp of Batt TB1 to TB3" is 80°C (176°F) or more. B


e.

Turn the power switch off.



A

5.READ VALUE USING INTELLIGENT TESTER

B

6.REPLACE POWER MANAGEMENT CONTROL ECU
5.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / "Temp of Batt TB1 to TB3".


d.

According to the display on the intelligent tester, read the Data List and check that the value of each "Temp of Batt TB1 to TB3" is 40°C (104°F) or less.

HINT:

If the value of any of "Temp of Batt TB1 to TB3" is more than 40°C (104°F), turn the power switch off and wait until the values to decrease to 40°C (104°F) or less before continuing this procedure.



e.

Enter the following menus: Powertrain / Hybrid Control / Data List / "Battery Block Vol - V01 to V10".


f.

According to the display on the intelligent tester, read the Data List and check the value of each "Battery Block Vol-V01 to V10" with the ignition switch ON (IG).

A408987C03
4.823,1.625 5.146,1 5.146,1 5.396,1 false 1.552,3.344 1.865,3.542 0.313,0.198 10 false *a 2.073,3.344 2.385,3.542 0.313,0.198 10 false *b 2.583,3.344 2.896,3.542 0.313,0.198 10 false *c 3.021,3.344 3.333,3.542 0.313,0.198 10 false *d 3.51,3.333 3.823,3.531 0.313,0.198 10 false *e 4,3.344 4.313,3.542 0.313,0.198 10 false *f 4.438,3.333 4.75,3.531 0.313,0.198 10 false *g 5.146,3.344 5.458,3.542 0.313,0.198 10 false *h 5.635,3.344 5.948,3.542 0.313,0.198 10 false *i 5.448,0.906 6.365,1.104 0.917,0.198 10 false 0.3 V or more 0.021,0.021 2.99,0.583 2.969,0.563 10 false (Example for when the difference of voltage value occurs between the hybrid battery block 2 and 7) 2.115,3.5 2.271,3.698 0.156,0.198 10 false A 4.5,3.5 4.656,3.698 0.156,0.198 10 false B 4.469,0.094 7.156,0.365 2.688,0.271 10 false A: Lowest HV Battery Block Voltage 4.469,0.417 7.156,0.688 2.688,0.271 10 false B: Highest HV Battery Block Voltage 6.146,3.333 6.458,3.531 0.313,0.198 10 false *j
*a Battery Block Vol -V01 *b Battery Block Vol -V02
*c Battery Block Vol -V03 *d Battery Block Vol -V04
*e Battery Block Vol -V05 *f Battery Block Vol -V06
*g Battery Block Vol -V07 *h Battery Block Vol -V08
*i Battery Block Vol -V09 *j Battery Block Vol -V10



Result:
Result Proceed to
Other than below A
The difference between the lowest and highest HV battery block voltage is 0.3 V or more. B


g.

Turn the power switch off.



A

COMPLETED

B

6.REPLACE POWER MANAGEMENT CONTROL ECU