Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P3107-213  Lost Communication with Airbag System Control Module  


DESCRIPTION

The power management control ECU detects a problem in the collision signal line from the airbag sensor assembly and alerts the driver.


DTC No. INF Code DTC Detection Condition Trouble Area
P3107 213 Short to GND in the communication circuit
·

Wire harness or connector

·

Airbag sensor assembly

·

Power management control ECU



WIRING DIAGRAM

A254875E84
4.906,1 5.323,1.156 0.417,0.156 10 false ABFS 1.906,0.99 2.354,1.146 0.448,0.156 10 false GSW2 2.135,1.302 2.344,1.458 0.208,0.156 10 false E1 4.635,1 4.833,1.156 0.198,0.156 10 false 29 4.448,2.073 4.844,2.24 0.396,0.167 10 false G57 4.448,2.24 6.573,2.396 2.125,0.156 10 false Power Management Control ECU 0.958,2.073 1.313,2.26 0.354,0.188 10 false G18 0.958,2.24 2.552,2.396 1.594,0.156 10 false Airbag Sensor Assembly 2.396,0.99 2.604,1.146 0.208,0.156 10 false 14 2.396,1.302 2.604,1.458 0.208,0.156 10 false 25 5.552,0.427 5.844,0.583 0.292,0.156 10 false +B

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (IG) and wait for 15 seconds or more.



PROCEDURE

1.CHECK DTC OUTPUT (SRS AIRBAG)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Body / SRS Airbag / DTC.


d.

Check if DTCs are output.


Result:
Result Proceed to
Airbag system DTCs are not output. A
Airbag system DTCs are output. B


e.

Turn the power switch off.



A

2.CHECK AIRBAG SENSOR ASSEMBLY (CHECK WAVEFORM)

B

2.CHECK AIRBAG SENSOR ASSEMBLY (CHECK WAVEFORM)
a.

Connect an oscilloscope between the airbag sensor assembly terminals specified in the table below.


b.

Turn the power switch on (READY).


c.
U158886E02
1.063,1.198 0.302,1.74 false 1.135,1.104 1.771,1.75 false 0.125,0.052 0.385,0.229 0.26,0.177 10 false *a 1.635,1.771 2.073,1.948 0.438,0.177 10 false GSW2 0.198,1.771 0.458,1.948 0.26,0.177 10 false E1 2.896,3.417 3.333,3.594 0.438,0.177 10 false GND 0.948,1.865 1.26,2.031 0.313,0.167 10 false G18

Measure the waveform.

Item Contents
Terminal G18-14 (GSW2) - G18-25 (E1)
Equipment Setting 5V/DIV., 500ms/DIV.
Condition Power switch on (READY)

Result:
Result Proceed to
The waveform appears as shown in the illustration. A
The waveform differs from the one shown in the illustration. B


Text in Illustration
*a Component with harness connected
(Airbag Sensor Assembly)


d.

Turn the power switch off.



A

3.CLEAR DTC

B

6.CHECK AIRBAG SENSOR ASSEMBLY
3.CLEAR DTC

NEXT

4.CHECK DTC OUTPUT (HYBRID CONTROL)
4.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
P3107-213 is not output. A
P3107-213 is output. B



e.

Turn the power switch off.



A

5.CHECK FOR INTERMITTENT PROBLEMS

B

5.CHECK FOR INTERMITTENT PROBLEMS

OK

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

6.CHECK AIRBAG SENSOR ASSEMBLY
a.

Disconnect connector G18 from the airbag sensor assembly.


b.
U158931E02
1.177,1.115 0.563,1.719 false 1.25,1.021 1.688,1.667 false 0.177,0.083 0.427,0.302 0.25,0.219 10 false *a 1.719,1.615 2.219,1.833 0.5,0.219 10 false GSW2 0.365,1.646 0.615,1.865 0.25,0.219 10 false E1 1.042,0.333 1.344,0.5 0.302,0.167 10 false G18

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G18-14 (GSW2) - G18-25 (E1) Power switch off 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Airbag Sensor Assembly)


c.

Connect the airbag sensor assembly connector.



OK

7.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - AIRBAG SENSOR ASSEMBLY)

NG

7.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect connector G57 from the power management control ECU.


b.

Disconnect connector G18 from the airbag sensor assembly.


c.
U183221E02
2.24,1.833 2.542,2.063 false 1.271,3.854 1.771,4.229 false 0.063,0 0.333,0.198 0.271,0.198 10 false *a 0.083,2.385 0.354,2.583 0.271,0.198 10 false *b 1.313,1.563 1.604,1.729 0.292,0.167 10 false G57 0.427,3.719 0.729,3.885 0.302,0.167 10 false G18 2.594,2.01 3.063,2.208 0.469,0.198 10 false ABFS 1.802,4.167 2.438,4.385 0.635,0.219 10 false GSW2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G57-29 (ABFS) or G18-14 (GSW2) - Body ground and other terminals Power switch off 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)


d.

Connect the airbag sensor assembly connector.


e.

Connect the power management control ECU connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR