Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P3108-536  Lost Communication with A/C System Control Module  


DESCRIPTION

The hybrid vehicle control ECU detects a wiring malfunction in the serial communication line between it and the compressor with motor assembly.


DTC No. INF Code DTC Detection Condition Trouble Area
P3108 536 A/C inverter malfunction
·

Wire harness or connector

·

Compressor with motor assembly

·

Hybrid vehicle control ECU



WIRING DIAGRAM

A379091E06
1.375,0.635 1.865,0.906 0.49,0.271 10 false IG1 2.167,0.698 2.656,0.969 0.49,0.271 10 false CLK 2.208,1.167 2.698,1.438 0.49,0.271 10 false DIN 2.083,1.635 2.573,1.906 0.49,0.271 10 false DOUT 2.135,2.125 2.625,2.396 0.49,0.271 10 false STBI 2.125,2.542 2.615,2.813 0.49,0.271 10 false GND 1.177,0.51 1.667,0.781 0.49,0.271 10 false 6 2.521,0.698 3.01,0.969 0.49,0.271 10 false 1 2.521,1.167 3.01,1.438 0.49,0.271 10 false 2 2.531,1.635 3.021,1.906 0.49,0.271 10 false 3 2.531,2.125 3.021,2.396 0.49,0.271 10 false 4 2.531,2.448 3.021,2.719 0.49,0.271 10 false 5 1.323,2.927 1.813,3.198 0.49,0.271 10 false C22 1.323,3.083 2.417,3.49 1.094,0.406 10 false Compressor with Motor Assembly 5.24,2.927 5.729,3.198 0.49,0.271 10 false A72 5.24,3.083 6.99,3.458 1.75,0.375 10 false Hybrid Vehicle Control ECU 5.083,0.708 5.573,0.979 0.49,0.271 10 false 10 5.156,1.188 5.646,1.458 0.49,0.271 10 false 9 5.146,1.656 5.635,1.927 0.49,0.271 10 false 8 5.104,2.125 5.594,2.396 0.49,0.271 10 false 11 1.573,1.615 2.063,1.885 0.49,0.271 10 false +B 0.49,0.781 1.021,1.052 0.531,0.271 10 false HTR-IG 5.333,1.198 5.823,1.469 0.49,0.271 10 false ITE 5.333,1.656 5.823,1.927 0.49,0.271 10 false ETI 1.583,2.083 2.073,2.354 0.49,0.271 10 false +B 5.344,2.115 5.833,2.385 0.49,0.271 10 false STB 5.323,0.719 5.813,0.99 0.49,0.271 10 false CLK 5.823,0.604 6.313,0.875 0.49,0.271 10 false +B 5.802,1.115 6.292,1.385 0.49,0.271 10 false +B

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Wait for 30 seconds or more with the power switch on (READY) and the air conditioning turned off.

2.

Turn the air conditioning on and wait for 30 seconds or more.



PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

2.CHECK CONNECTOR CONNECTION CONDITION (COMPRESSOR WITH MOTOR ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

2.CHECK CONNECTOR CONNECTION CONDITION (COMPRESSOR WITH MOTOR ASSEMBLY CONNECTOR)
a.
U159038E02
1.854,0.208 2.125,0.365 0.271,0.156 10 false C22

Check the connection of connector C22 of the compressor with motor assembly.

OK:

The connector is connected securely and there are no contact problems.




OK

3.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY POWER SOURCE CIRCUIT)

NG

CONNECT SECURELY

3.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY POWER SOURCE CIRCUIT)
a.

Disconnect connector C22 from the compressor with motor assembly.


b.
U158852E02
1.906,1.125 2.042,1.656 false 2.042,1.125 2.458,1.656 false 0.24,0.188 0.469,0.365 0.229,0.177 10 false *a 0.469,1.052 0.74,1.219 0.271,0.167 10 false C22 1.896,1.698 2.229,1.865 0.333,0.167 10 false GND 2.458,1.698 2.719,1.865 0.26,0.167 10 false IG1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
C22-5 (GND) - Body ground Power switch off Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Compressor with Motor Assembly)


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C22-6 (IG1) - C22-5 (GND) Power switch on (IG) 11 to 14 V


NOTICE:

Turning the power switch on (IG) with the compressor with motor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Turn the power switch off.


f.

Connect the compressor with motor assembly connector.



OK

4.CHECK DTC OUTPUT (HYBRID CONTROL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (READY).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
P3108-536 is output. A
P3108-536 is not output. B



e.

Turn the power switch off.



A

5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - COMPRESSOR WITH MOTOR ASSEMBLY)

B

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - COMPRESSOR WITH MOTOR ASSEMBLY)
5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - COMPRESSOR WITH MOTOR ASSEMBLY)
a.

Disconnect connector A72 from the hybrid vehicle control ECU.


b.

Disconnect connector C22 from the compressor with motor assembly.


c.

Turn the power switch on (IG).


d.
U183344E02
1.583,2.177 1.052,2.688 false 1.677,2.177 2.115,2.688 false 1.635,2.177 1.625,2.677 false 1.323,3.75 1.063,4.271 false 1.615,3.75 1.875,4.271 false 1.458,3.76 1.458,4.271 false 0.177,1.854 0.448,2.021 0.271,0.167 10 false A72 0.49,3.677 0.76,3.844 0.271,0.167 10 false C22 0.167,0.156 0.344,0.323 0.177,0.167 10 false *a 0.167,3.021 0.344,3.188 0.177,0.167 10 false *b 0.917,2.677 1.229,2.844 0.313,0.167 10 false CLK 2.052,2.698 2.365,2.865 0.313,0.167 10 false ETI 1.552,2.688 1.865,2.854 0.313,0.167 10 false ITE 0.885,4.292 1.198,4.458 0.313,0.167 10 false CLK 1.365,4.302 1.646,4.469 0.281,0.167 10 false DIN 1.802,4.302 2.229,4.469 0.427,0.167 10 false DOUT

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A72-10 (CLK) - Body ground Power switch on (IG) Below 1 V
A72-8 (ETI) - Body ground Power switch on (IG) Below 1 V
A72-9 (ITE) - Body ground Power switch on (IG) Below 1 V


Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Compressor with Motor Assembly)

NOTICE:

Turning the power switch on (IG) with the hybrid vehicle control ECU connector and the compressor with motor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Turn the power switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
A72-10 (CLK) - C22-1 (CLK) Power switch off Below 1 Ω
A72-8 (ETI) - C22-3 (DOUT) Power switch off Below 1 Ω
A72-9 (ITE) - C22-2 (DIN) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
A72-10 (CLK) or C22-1 (CLK) - Body ground and other terminals Power switch off 10 kΩ or higher
A72-8 (ETI) or C22-3 (DOUT) - Body ground and other terminals Power switch off 10 kΩ or higher
A72-9 (ITE) or C22-2 (DIN) - Body ground and other terminals Power switch off 10 kΩ or higher



g.

Connect the compressor with motor assembly connector.


h.

Connect the hybrid vehicle control ECU connector.



OK

6.CHECK HYBRID VEHICLE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HYBRID VEHICLE CONTROL ECU
a.

Disconnect connector C22 from the compressor with motor assembly.


b.
U183198E02
1.333,1.125 1.042,1.708 false 1.646,1.125 1.938,1.708 false 1.49,1.135 1.49,1.708 false 0.167,0.156 0.375,0.333 0.208,0.177 10 false *a 0.427,1.021 0.698,1.188 0.271,0.167 10 false C22 0.813,1.75 1.135,1.917 0.323,0.167 10 false CLK 1.385,1.75 1.708,1.917 0.323,0.167 10 false DIN 1.875,1.75 2.302,1.917 0.427,0.167 10 false DOUT

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
C22-3 (DOUT) - Body ground Power switch off 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Compressor with Motor Assembly)


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C22-1 (CLK) - Body ground Power switch on (IG) 11 to 14 V
C22-2 (DIN) - Body ground Power switch on (IG) 11 to 14 V
C22-3 (DOUT) - Body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the compressor with motor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Turn the power switch off.


f.

Connect the compressor with motor assembly connector.



OK

7.CHECK COMPRESSOR WITH MOTOR ASSEMBLY

NG

7.CHECK COMPRESSOR WITH MOTOR ASSEMBLY
a.

Disconnect connector A72 from the hybrid vehicle control ECU.


b.
U183265E02
1.667,2.323 2.177,2.865 false 1.625,2.323 1.625,2.865 false 1.583,2.323 0.979,2.875 false 0.594,2.229 0.865,2.396 0.271,0.167 10 false A72 2.125,2.885 2.448,3.052 0.323,0.167 10 false ETI 1.521,2.885 1.792,3.063 0.271,0.177 10 false ITE 0.052,0.01 0.208,0.177 0.156,0.167 10 false *a 0.771,2.885 1.146,3.063 0.375,0.177 10 false CLK

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A72-10 (CLK) - Body ground Power switch off 10 kΩ or higher
A72-9 (ITE) - Body ground Power switch off 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A72-8 (ETI) - Body ground Power switch on (IG) 11 to 14 V
A72-10 (CLK) - Body ground Power switch on (IG) Below 1 V
A72-9 (ITE) - Body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the hybrid vehicle control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Turn the power switch off.


f.

Connect the hybrid vehicle control ECU connector.



OK

NG

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - COMPRESSOR WITH MOTOR ASSEMBLY)
a.

Disconnect connector A72 from the hybrid vehicle control ECU.


b.

Disconnect connector C22 from the compressor with motor assembly.


c.

Turn the power switch on (IG).


d.
U183345E02
1.542,2.177 2.073,2.479 false 1.74,3.75 2,4.26 false 0.583,2.083 0.854,2.25 0.271,0.167 10 false A72 0.448,3.667 0.719,3.833 0.271,0.167 10 false C22 0.094,0.156 0.271,0.323 0.177,0.167 10 false *a 0.094,3.021 0.271,3.188 0.177,0.167 10 false *b 2.115,2.417 2.427,2.583 0.313,0.167 10 false STB 1.885,4.302 2.313,4.469 0.427,0.167 10 false STBI

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A72-11 (STB) - Body ground Power switch on (IG) Below 1 V


Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Compressor with Motor Assembly)

NOTICE:

Turning the power switch on (IG) with the hybrid vehicle control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Turn the power switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
A72-11 (STB) - C22-4 (STBI) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
A72-11 (STB) or C22-4 (STBI) - Body ground and other terminals Power switch off 10 kΩ or higher



g.

Connect the compressor with motor assembly connector.


h.

Connect the hybrid vehicle control ECU connector.



OK

9.CHECK HYBRID VEHICLE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HYBRID VEHICLE CONTROL ECU
a.

Disconnect connector C22 from the compressor with motor assembly.


b.
U183199E02
1.771,1.125 1.917,1.656 false 0.24,0.188 0.469,0.365 0.229,0.177 10 false *a 0.469,1.052 0.74,1.219 0.271,0.167 10 false C22 1.813,1.698 2.219,1.865 0.406,0.167 10 false STBI

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
C22-4 (STBI) - Body ground Power switch off 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Compressor with Motor Assembly)


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C22-4 (STBI) - Body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the compressor with motor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Turn the power switch off.


f.

Connect the compressor with motor assembly connector.



OK

10.CHECK COMPRESSOR WITH MOTOR ASSEMBLY

NG

10.CHECK COMPRESSOR WITH MOTOR ASSEMBLY
a.

Disconnect connector A72 from the hybrid vehicle control ECU.


b.
U183266E02
1.542,2.323 1.958,2.573 false 1.323,2.896 1.594,3.063 0.271,0.167 10 false A72 0.052,0.042 0.208,0.208 0.156,0.167 10 false *a 1.979,2.573 2.354,2.75 0.375,0.177 10 false STB

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A72-11 (STB) - Body ground Power switch off 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A72-11 (STB) - Body ground Power switch on (IG) 11 to 14 V


NOTICE:

Turning the power switch on (IG) with the hybrid vehicle control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Turn the power switch off.


f.

Connect the hybrid vehicle control ECU connector.



OK

NG

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY