The MG ECU located in the inverter with converter assembly monitors its internal operation and it will set DTCs when it detects malfunctions.
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| P06B0 | 163 | MG ECU internal malfunction
IPM positive power source error (1 trip detection logic) |
Inverter with converter assembly |
| P06D6 | 511 | MG ECU internal malfunction
Standard voltage for analog signal offset (+2.5 V) error (1 trip detection logic) |
|
| P06E6 | 164 | MG ECU internal malfunction
IPM negative power source error (1 trip detection logic) |
|
| P0A1A | 151 | MG ECU internal malfunction
Run pulse signal cycle deviation or stop (1 trip detection logic) |
|
| P0A1A | 166 | MG ECU internal malfunction
R/D converter NM stop error (1 trip detection logic) |
|
| P0A1A | 658 | MG ECU internal malfunction
Calculation check error (1 trip detection logic) |
|
| P0A1A | 791 | MG ECU internal malfunction
R/D converter communication error (1 trip detection logic) |
|
| P0A1B | 198 | MG ECU internal malfunction
R/D converter NM stop error (1 trip detection logic) |
|
| P0A1B | 786 | MG ECU internal malfunction
Calculation check error (1 trip detection logic) |
|
| P0A1B | 794 | MG ECU internal malfunction
R/D converter communication error (1 trip detection logic) |
|
| P1C2A | 155 | MG ECU internal malfunction
A/D converter malfunction (1 trip detection logic) |
|
| P1C2B | 192 | MG ECU internal malfunction
A/D converter malfunction (1 trip detection logic) |
|
| P1C73 | 512 | MG ECU internal malfunction
Standard voltage for analog signal (+5 V) error (1 trip detection logic) |
|
| P1CA6 | 156 | MG ECU internal malfunction
CPU ROM-RAM error (1 trip detection logic) |
|
| P1CA7 | 193 | MG ECU internal malfunction
CPU ROM-RAM error (1 trip detection logic) |
|
| P3133 | 659 | MG ECU internal malfunction
Communication error (from generator (MG1) to motor (MG2)) (1 trip detection logic) |
|
| P3134 | 661 | MG ECU internal malfunction
Communication error (from motor (MG2) to generator (MG1)) (1 trip detection logic) |
If DTC P06B0-163, P06D6-511, P06E6-164, P0A1A-151, P0A1A-658, P0A1A-791, P0A1B-786, P0A1B-794, P1C2A-155, P1C2B-192, P1C73-512, P3133-659 or P3134-661 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.
Turn the power switch on (IG) and wait for 5 seconds or more.
If DTC P1CA6-156 or P1CA7-193 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.
Turn the power switch on (IG) and wait for 1 minute or more.
If DTC P0A1A-166 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.
Turn the power switch on (READY).
With the vehicle stopped and the shift lever in P, depress the accelerator pedal and start the engine.
Depress the accelerator pedal and keep the engine running for 30 seconds or more.
If DTC P0A1B-198 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.
Turn the power switch on (READY).
Drive the vehicle at 5 km/h (3 mph) or more for 30 seconds or more.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| None of the following DTCs are output. | A |
| Any of the following DTCs are output. | B |
| DTC No. | Relevant Diagnosis |
|---|---|
| P06B0-163 | Sensor Power Supply "A" Circuit / Open |
| P06D6-511 | Sensor Reference Voltage "F" Circuit / Open |
| P06E6-164 | Sensor Power Supply "C" Circuit / Open |
| P0A1A-166, 658, 791 | Generator Control Module |
| P0A1B-198, 786, 794 | Drive Motor "A" Control Module |
| P1C2A-155 | Generator A/D Converter Circuit |
| P1C2B-192 | Drive Motor "A" A/D Converter Circuit |
| P1C73-512 | Sensor Standard Voltage "F" Circuit / Open |
| P1CA6-156 | Generator Control Module Malfunction |
| P1CA7-193 | Drive Motor Control Module Malfunction |
| P3134-661 | Communication Error from Drive Motor "A" to Generator |
Turn the power switch off.
A
B
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| Only DTC P0A1A-151, P3133-659 or P324E-788 is output. | A |
| Other than above. | B |
Turn the power switch off.
A
B
(See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART)
NEXT
Connect the intelligent tester to the DLC3.
Turn the power switch off and wait for 30 seconds or more.
Turn the power switch on (IG) and wait for 5 seconds or more.
Turn the power switch on (READY).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| No DTCs are output (not including history DTCs). | A |
| Only DTC P0A1A-151, P3133-659 or P324E-788 is output. | B |
| Other than above. | C |
Turn the power switch off.
A
B
C
(See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART)