Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0E32-585  DC/DC Converter Voltage Sensor "A" Range / Performance  


DESCRIPTION

The MG ECU uses a voltage sensor that is built into the boost converter to detect pre-boost high voltage (VL) to allow boost control. The MG ECU monitors the boost converter voltage sensor signal line and detects the following malfunctions.

DTC No. INF Code DTC Detection Condition Trouble Area
P0E32 585 Boost converter voltage (VL) sensor performance problem Inverter with converter assembly

CAUTION / NOTICE / HINT

HINT:

When the accelerator pedal is not depressed with the power switch on (READY) and the shift lever in P, if "VL-Voltage before Boosting" and the "Power Resource VB" is approximately same after repair, the condition is judged as normal.


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check if DTCs are output.

Result:
Result Proceed to
Only P0E32-585 is output or P0E32-585 and DTCs other than the ones in the table below are also output. A
DTCs shown in Table 1 are output simultaneously. B
DTCs shown in Table 2 are output simultaneously. C


Table 1
DTC No. Relevant Diagnosis
P06E6-164 Sensor Power Supply "C" Circuit/Open
P0A1A-151, 658 Generator Control Module
P0A1B-786 Drive Motor "A" Control Module
P0A1D-148 Hybrid Powertrain Control Module
P0D2F-266 Drive Motor "A" Inverter Voltage Sensor Circuit Low
P0D30-267 Drive Motor "A" Inverter Performance
P0E33-589 DC/DC Converter Voltage Sensor "A" Low
P0E34-590 DC/DC Converter Voltage Sensor "A" High
P1C2A-155 Generator A/D Converter Circuit
P1C73-512 Sensor Standard Voltage "F" Circuit/Open
P1CA6-156 Generator Control Module Malfunction
P1CA7-193 Drive Motor Control Module Malfunction
P2511-149 HV CPU Power Relay Sense Circuit Intermittent No Continuity
P3004-132 High Voltage Power Resource
P3133-659 Communication Error from Generator to Drive Motor "A"
P3134-661 Communication Error from Drive Motor "A" to Generator
P324E-788 MG-ECU Power Relay Intermittent Circuit
U0110 (all INF codes)*1 Lost Communication with Drive Motor Control Module "A"

Table 2
DTC No. Relevant Diagnosis
P0AFC-123 Hybrid Battery Pack Sensor Module
P0B3D-123 Hybrid Battery Voltage Sensor "A" Circuit Low
P0B42-123 Hybrid Battery Voltage Sensor "B" Circuit Low
P0B47-123 Hybrid Battery Voltage Sensor "C" Circuit Low
P0B4C-123 Hybrid Battery Voltage Sensor "D" Circuit Low
P0B51-123 Hybrid Battery Voltage Sensor "E" Circuit Low
P0B56-123 Hybrid Battery Voltage Sensor "F" Circuit Low
P0B5B-123 Hybrid Battery Voltage Sensor "G" Circuit Low
P0B60-123 Hybrid Battery Voltage Sensor "H" Circuit Low
P0B65-123 Hybrid Battery Voltage Sensor "I" Circuit Low
P0B6A-123 Hybrid Battery Voltage Sensor "J" Circuit Low
P0B6F-123 Hybrid Battery Voltage Sensor "K" Circuit Low
P308A-123 Hybrid Battery Voltage Sensor All Circuits Low

HINT:
·

*1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.

·

P0E32-585 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.




e.

Turn the power switch off.



A

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

B

C