Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM › from 2014.12
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277925 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0AFC-123  Hybrid Battery Pack Sensor Module  


DESCRIPTION

If the battery smart unit detects an internal malfunction, it sends an error signal to the hybrid vehicle control ECU. When the hybrid vehicle control ECU receives the error signal from the battery smart unit, the ECU warns the driver and performs fail-safe control.


DTC No. INF Code DTC Detection Condition Trouble Area
P0AFC 123 The hybrid vehicle control ECU receives an error signal from the battery smart unit.
·

Battery smart unit

·

Wire harness or connector



WIRING DIAGRAM

A244329E14
5.281,3.448 6.49,3.656 1.208,0.208 10 false Battery Smart Unit 2.281,0.917 2.708,1.135 0.427,0.219 10 false IGCT 4.625,0.448 5.573,0.646 0.948,0.198 10 false IGCT No. 4 0.625,2.76 1.656,2.958 1.031,0.198 10 false Auxiliary Battery 2.698,1.292 3.135,1.438 0.438,0.146 10 false MREL 2.698,2.354 3.135,2.5 0.438,0.146 10 false BTH+ 2.698,2.688 3.135,2.833 0.438,0.146 10 false BTH- 3.146,1.281 3.448,1.427 0.302,0.146 10 false A72 3.198,2.198 3.5,2.344 0.302,0.146 10 false 32 3.146,2.354 3.479,2.5 0.333,0.146 10 false G80 5.667,2.365 6.042,2.51 0.375,0.146 10 false BTH+ 5.667,2.698 6.042,2.844 0.375,0.146 10 false BTH- 5.469,2.188 5.656,2.354 0.188,0.167 10 false 1 5.667,0.281 6.104,0.458 0.438,0.177 10 false IGCT 2.771,0.198 2.99,0.365 0.219,0.167 10 false 5 2.042,0.198 2.24,0.354 0.198,0.156 10 false 3 2.042,0.563 2.25,0.708 0.208,0.146 10 false 2 2.76,0.552 2.958,0.729 0.198,0.177 10 false 1 4.719,0.156 4.833,0.313 0.115,0.156 10 false 1 5.115,0.156 5.26,0.333 0.146,0.177 10 false 2 5.667,3.042 6.042,3.188 0.375,0.146 10 false GND 5.469,2.865 5.656,3 0.188,0.135 10 false 6 0.49,0.854 1.271,1.073 0.781,0.219 10 false IGCT-MAIN 0.51,2.01 1.292,2.229 0.781,0.219 10 false MAIN 3.219,1.125 3.417,1.302 0.198,0.177 10 false 6 3.135,2.698 3.49,2.844 0.354,0.146 10 false G80 3.188,2.531 3.375,2.677 0.188,0.146 10 false 33 5.469,2.552 5.656,2.719 0.188,0.167 10 false 4 5.479,0.156 5.625,0.333 0.146,0.177 10 false 3 2.156,3.021 3.531,3.438 1.375,0.417 10 false Hybrid Vehicle Control ECU 5.281,3.292 5.781,3.521 0.5,0.229 10 false M39 2.823,1.646 3.146,1.844 0.323,0.198 10 false +B1 2.823,1.99 3.177,2.188 0.354,0.198 10 false +B2 3.229,1.5 3.427,1.677 0.198,0.177 10 false 4 3.229,1.833 3.427,2.01 0.198,0.177 10 false 1 3.135,1.656 3.438,1.802 0.302,0.146 10 false A72 3.135,2 3.438,2.146 0.302,0.146 10 false A71 4.344,1.094 5.198,1.313 0.854,0.219 10 false IGCT No. 2 4.104,0.875 4.219,1.031 0.115,0.156 10 false 1 4.104,1.292 4.25,1.469 0.146,0.177 10 false 2 0.271,1.042 0.385,1.198 0.115,0.156 10 false 1 0.271,0.635 0.417,0.813 0.146,0.177 10 false 2

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION).

HINT:

At least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

After repairing, restart the system (turn the power switch on (READY)) and recheck for DTCs (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DTC CHECK / CLEAR).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IGCT VOLTAGE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery exhaust duct (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY SMART UNIT>REMOVAL).


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
U158969E03
1.333,1.229 1.031,0.531 true 1.333,1.292 0.531,2.49 true 0.146,0.125 0.333,0.292 0.188,0.167 10 false *a 0.313,2.521 0.656,2.76 0.344,0.24 10 false GND 0.698,0.406 1.083,0.625 0.385,0.219 10 false IGCT 0.313,1.188 0.823,1.479 0.51,0.292 10 false M39

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M39-3 (IGCT) - M39-6 (GND) Power switch on (IG) 11 to 14 V


Text in Illustration
*a Component with harness connected
(Battery Smart Unit)


NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the No. 1 hybrid battery exhaust duct.



OK

NG

2.CHECK HARNESS AND CONNECTOR (GND - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (GND - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery exhaust duct (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY SMART UNIT>REMOVAL).


c.
U158970E02
1.323,1.292 0.375,2.458 true 0.302,0.125 0.49,0.292 0.188,0.167 10 false *a 0.198,2.49 0.563,2.729 0.365,0.24 10 false GND 0.344,1.167 0.729,1.354 0.385,0.188 10 false M39

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
M39-6 (GND) - Body ground Power switch off Below 1 Ω


Text in Illustration
*a Component with harness connected
(Battery Smart Unit)


d.

Install the No. 1 hybrid battery exhaust duct.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATT VL SSR FUSE - BATTERY SMART UNIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND - BODY GROUND)