Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM › from 2015.11
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277925 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0B3D-123  Hybrid Battery Voltage Sensor "A" Circuit Low  P0B42-123  Hybrid Battery Voltage Sensor "B" Circuit Low  P0B47-123  Hybrid Battery Voltage Sensor "C" Circuit Low  P0B4C-123  Hybrid Battery Voltage Sensor "D" Circuit Low  P0B51-123  Hybrid Battery Voltage Sensor "E" Circuit Low  P0B56-123  Hybrid Battery Voltage Sensor "F" Circuit Low  P0B5B-123  Hybrid Battery Voltage Sensor "G" Circuit Low  P0B60-123  Hybrid Battery Voltage Sensor "H" Circuit Low  P0B65-123  Hybrid Battery Voltage Sensor "I" Circuit Low  P0B6A-123  Hybrid Battery Voltage Sensor "J" Circuit Low  P0B6F-123  Hybrid Battery Voltage Sensor "K" Circuit Low  P308A-123  Hybrid Battery Voltage Sensor All Circuits Low  


DESCRIPTION

Refer to the description for DTC P0A80-123 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A80-123).


DTC No. INF Code DTC Detection Condition Trouble Area
P0B3D
P0B42
P0B47
P0B4C
P0B51
P0B56
P0B5B
P0B60
P0B65
P0B6A
P0B6F
P308A
123 Each battery block voltage becomes less than 2.5 V (open) (1 trip detection)
·

Battery smart unit

·

HV battery



HINT:
·

Values smaller than 2.0 V may not be shown in the Data List because a fail-safe value is substituted.

·

Hybrid battery voltage sensor in the DTC titles refers to the battery smart unit.



CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION).

HINT:

At least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.



NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Read output DTCs (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
P0AFC-123 or P0A95-123 is not output. A
P0AFC-123 or P0A95-123 is also output. B



e.

Turn the power switch off.


f.

Disconnect the intelligent tester from the DLC3.



A

2.CHECK CONNECTOR CONNECTION CONDITION

B

2.CHECK CONNECTOR CONNECTION CONDITION
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery shield sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY SMART UNIT>REMOVAL).


c.
U158940E04
1.573,1.542 1.75,1.729 0.177,0.188 10 false z9

Check the connections of the z9 connector of the battery smart unit.

OK:

The connectors are connected securely and there are no contact problems.



d.

Install the No. 1 hybrid battery shield sub-assembly.



OK

3.REPLACE BATTERY SMART UNIT

NG

CONNECT SECURELY

3.REPLACE BATTERY SMART UNIT

NEXT

4.CLEAR DTC (HV)
4.CLEAR DTC (HV)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.



e.

Perform a road test to charge and discharge the HV battery.


f.

Disconnect the intelligent tester from the DLC3.



NEXT

5.RECONFIRM DTC OUTPUT (HV)
5.RECONFIRM DTC OUTPUT (HV)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Read output DTCs (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
Hybrid battery voltage sensor circuit DTCs for this diagnostic procedure are not output A
Hybrid battery voltage sensor circuit DTCs for this diagnostic procedure are output B



NOTICE:

Turning the power switch on (IG) with the service grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


e.

Turn the power switch off.


f.

Disconnect the intelligent tester from the DLC3.



A

RETURN TO NORMAL OPERATION

B