Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HV RELAY ASSEMBLY
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277934 HV RELAY ASSEMBLY G

HYBRID / BATTERY CONTROL  HV RELAY ASSEMBLY  INSPECTION  


PROCEDURE

Hide G92Z0 1.INSPECT HYBRID BATTERY JUNCTION BLOCK ASSEMBLY

a.

Inspect SMRB.

i.
A381346E02
0.521,0.698 0.833,0.802 false 2.979,1.427 2.74,1.219 false 0.979,2.802 1.219,2.521 false 1.604,2.823 1.344,2.521 false 0.094,0.094 0.438,0.354 0.344,0.26 10 false *a 0.229,0.615 0.573,0.875 0.344,0.26 10 false CBI 1.146,0.448 1.49,0.708 0.344,0.26 10 false P5 3.042,0.823 3.385,1.083 0.344,0.26 10 false A 3.031,1.406 3.375,1.667 0.344,0.26 10 false + 1.51,2.854 2.063,3.135 0.552,0.281 10 false SMRB 0.802,2.844 1.146,3.104 0.344,0.26 10 false GND 0.188,2.177 0.531,2.438 0.344,0.26 10 false M40

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (+) - P5-1 (CBI) Auxiliary battery voltage is not applied between terminals M40- 1 (SMRB) and M40-2 (GND) 10 kΩ or higher
A-1 (+) - P5-1 (CBI) Auxiliary battery voltage is applied between terminals M40- 1 (SMRB) and M40-2 (GND) Below 1 Ω


Text in Illustration
*a Component without harness connected
(Hybrid Battery Junction Block Assembly)


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M40-1 (SMRB) - M40-2 (GND) -40 to 80°C (-40 to 176°F) 25.0 to 59.0 Ω


If the result is not as specified, replace the hybrid battery junction block assembly or electric vehicle fuse.



b.

Inspect SMRG.

i.
A381347E02
0.802,0.958 1.25,0.667 false 2.708,1.479 2.958,1.146 false 0.896,2.833 1.073,2.552 false 1.406,2.844 1.229,2.531 false 1.302,0.552 1.625,0.813 0.323,0.26 10 false CEI 0.25,0.927 0.573,1.188 0.323,0.26 10 false P4 0.063,0.198 0.385,0.458 0.323,0.26 10 false *a 0.26,2.292 0.583,2.552 0.323,0.26 10 false M40 0.677,2.865 1.188,3.146 0.51,0.281 10 false SMRG 1.313,2.875 1.802,3.146 0.49,0.271 10 false GND 2.917,1.667 3.24,1.927 0.323,0.26 10 false c1 3.01,1.042 3.333,1.302 0.323,0.26 10 false -

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
c1-1 (-) - P4-1 (CEI) Auxiliary battery voltage is not applied between terminals M40- 3 (SMRG) and M40-2 (GND) 10 kΩ or higher
c1-1 (-) - P4-1 (CEI) Auxiliary battery voltage is applied between terminals M40- 3 (SMRG) and M40-2 (GND) Below 1 Ω


Text in Illustration
*a Component without harness connected
(Hybrid Battery Junction Block Assembly)


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M40-3 (SMRG) - M40-2 (GND) -40 to 80°C (-40 to 176°F) 25.0 to 59.0 Ω


If the result is not as specified, replace the hybrid battery junction block assembly.



c.

Inspect SMRP.

i.
U158954E03
1.24,2.531 1.604,2.813 true 0.927,2.542 0.802,2.771 true 0.823,0.938 1.552,0.563 false 2.75,1.396 3.156,0.938 false 0.188,0.969 0.406,1.135 0.219,0.167 10 false P4 0.375,2.375 0.667,2.542 0.292,0.167 10 false M40 2.854,1.656 3.042,1.823 0.188,0.167 10 false c1 1.479,2.833 1.823,3 0.344,0.167 10 false GND 0.604,2.823 1.063,2.99 0.458,0.167 10 false SMRP 0.125,0.073 0.469,0.24 0.344,0.167 10 false *a 1.615,0.448 1.917,0.625 0.302,0.177 10 false CEI 3.208,0.813 3.292,0.99 0.083,0.177 10 false -

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P4-1 (CEI) - c1-1 (-) Auxiliary battery voltage is not applied between terminals M40-4 (SMRP) and M40-2 (GND) 10 kΩ or higher
P4-1 (CEI) - c1-1 (-) Auxiliary battery voltage is applied between terminals M40-4 (SMRP) and M40-2 (GND) 28.5 to 31.5 Ω


Text in Illustration
*a Component without harness connected
(Hybrid Battery Junction Block Assembly)


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M40-4 (SMRP) - M40-2 (GND) -40 to 80°C (-40 to 176°F) 112 to 274 Ω


If the result is not as specified, replace the hybrid battery junction block assembly.