Home › Engine / Hybrid System › 1NZ-FXE (ENGINE MECHANICAL) › FRONT CRANKSHAFT OIL SEAL › 2011.12–2017.06
RM2170E _51 Engine / Hybrid System _057005 1NZ-FXE ENGINE MECHANICAL _0277946 FRONT CRANKSHAFT OIL SEAL A

1NZ-FXE ENGINE MECHANICAL  FRONT CRANKSHAFT OIL SEAL  REMOVAL  


PROCEDURE

Hide 1.REMOVE FRONT WHEEL RH

Hide 51441C 2.REMOVE ENGINE UNDER COVER RH

Hide 3.SEPARATE NO. 2 ENGINE ROOM RELAY BLOCK AND NO. 2 JUNCTION BLOCK ASSEMBLY

a.
A268172

Remove the bolt and 2 nuts, and separate the No. 2 engine room relay block and No. 2 junction block assembly.


Hide 12305 4.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

a.
A266935

Place a jack underneath the engine, then put a wooden block on the jack.

Text in Illustration
V100145

Jack Position

NOTICE:

To prevent the No. 2 oil pan from deforming, do not place any attachments onto the No. 2 oil pan.



b.
A266934

Remove the 4 bolts, 2 nuts and engine mounting insulator sub-assembly RH.


Hide 13407 5.REMOVE CRANKSHAFT DAMPER SUB-ASSEMBLY

a.
A266936E01
0.484,0.035 0.781,0.181 0.297,0.145 10 SST 2.717,1.184 3.014,1.330 0.297,0.145 10 SST 3.087,1.678 3.242,1.824 0.155,0.145 10 *a 1.295,0.42 0.991,0.116 0.991,0.116 0.835,0.116 false 2.675,1.274 2.534,1.274 2.534,1.274 2.262,1.545 false 3.027,1.246 3.087,1.383 0.059,0.137 2.562,1.759 3.057,1.759 false

Using SST, hold the crankshaft damper sub-assembly in place and loosen the bolt.

Text in Illustration
*a Hold
V100135

Turn

SST
09213-58012  (91111-50845)
09330-00021  

NOTICE:

When installing SST, be careful that the bolt which holds SST does not interfere with the timing chain cover.



b.
A266938E01
0.11,0.135 0.399,0.277 0.289,0.142 10 SST 1.394,0.582 1.683,0.723 0.289,0.142 10 SST 1.852,2.725 2.004,2.867 0.152,0.142 10 *a 2.476,2.805 2.027,2.805 false 0.467,0.213 0.741,0.213 0.741,0.213 0.845,1.105 false 2.253,0.66 1.739,0.66 false

Using SST, remove the crankshaft damper sub-assembly and bolt.

Text in Illustration
*a Hold
V100135

Turn

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05021)

HINT:

Apply a lubricant to the threads and end of SST.



Hide 15100C 6.REMOVE OIL PUMP SEAL

a.
A266939E04
1.885,0.688 2.146,1.104 2.146,1.104 2.333,1.104 true 0.177,1.396 0.344,1.552 0.167,0.156 10 false *a 2.344,1.021 2.51,1.177 0.167,0.156 10 true *1

Using a knife, cut off the lip of the oil pump seal.

Text in Illustration
*1 Protective Tape
*a Cut Position


b.

Using a screwdriver with its tip wrapped with tape, pry out the oil seal.

NOTICE:

Do not damage the surface of the oil seal press fit hole or the crankshaft.


HINT:
·

Wrap the screwdriver tip with protective tape before use.

·

After removing, check the crankshaft for damage. If damaged, smooth the surface with 400-grit sandpaper.