Home › Engine / Hybrid System › 1NZ-FXE (ENGINE MECHANICAL) › REAR CRANKSHAFT OIL SEAL
RM2170E _51 Engine / Hybrid System _057005 1NZ-FXE ENGINE MECHANICAL _0277947 REAR CRANKSHAFT OIL SEAL A

1NZ-FXE ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


PROCEDURE

Hide 11401L 1.INSTALL REAR ENGINE OIL SEAL

a.

Apply MP grease to the lip of a new rear engine oil seal.

NOTICE:

Keep the lip free from foreign matter.



b.
A088161E06
2.656,1.292 2.427,1.292 2.427,1.292 2.052,1.135 true 2.688,1.219 2.99,1.365 0.302,0.146 10 true SST

Using SST and a hammer, tap in the rear engine oil seal until its surface is flush with the rear engine oil seal retainer edge.

SST
09223-56010  

Tap in depth:

0 to 1.0 mm from the edge of the timing chain cover.


NOTICE:
·

Do not tap the rear engine oil seal at an angle.

·

Wipe off extra grease from the crankshaft.




Hide 13405 2.INSTALL FLYWHEEL SUB-ASSEMBLY

a.
A266937E04
1.25,0.479 0.698,0.479 true 2.49,1.948 1.938,1.948 false 0.365,0.396 0.688,0.573 0.323,0.177 10 true SST 1.583,1.865 1.875,2.01 0.292,0.146 10 false SST

Using SST, hold the crankshaft damper sub-assembly.

SST
09213-58012  (91111-50845)
09330-00021  

NOTICE:

When installing SST, be careful that the bolt which holds SST does not interfere with the timing chain cover.



b.

Apply adhesive to the 2 or 3 end threads of 6 new bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Temporarily install the flywheel sub-assembly with the 6 new bolts.


d.
U159025E03
1.333,0.458 1.5,0.635 0.167,0.177 10 false 1 2.115,1.479 2.25,1.646 0.135,0.167 10 false 2 1.094,1.115 1.219,1.26 0.125,0.146 10 false 3 2.344,0.865 2.479,1.052 0.135,0.188 10 false 4 1.417,1.542 1.542,1.708 0.125,0.167 10 false 5 2.031,0.417 2.156,0.563 0.125,0.146 10 false 6

Tighten the 6 bolts in the sequence shown in the illustration.

Torque:
83 N*m (846 kgf*cm, 61 ft.*lbf)


Hide 31270 3.INSTALL TRANSMISSION INPUT DAMPER ASSEMBLY

a.
A266937E04
1.25,0.479 0.698,0.479 true 2.49,1.948 1.938,1.948 false 0.365,0.396 0.688,0.573 0.323,0.177 10 true SST 1.583,1.865 1.875,2.01 0.292,0.146 10 false SST

Using SST, hold the crankshaft damper sub-assembly.

SST
09213-58012  (91111-50845)
09330-00021  

NOTICE:

When installing SST, be careful that the bolt which holds SST does not interfere with the timing chain cover.



b.

Temporarily install the transmission input damper assembly with 6 new bolts.


c.
U159024E03
1.094,0.073 1.219,0.219 0.125,0.146 10 false 1 2.583,0.135 2.729,0.344 0.146,0.208 10 false 6 2.896,1.385 3.052,1.594 0.156,0.208 10 false 4 2.406,1.771 2.531,1.948 0.125,0.177 10 false 2 0.771,1.781 0.927,2.031 0.156,0.25 10 false 5 0.479,1.083 0.604,1.229 0.125,0.146 10 false 3

Tighten the 6 bolts in the sequence shown in the illustration.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:
·

Remove any oil from the transmission input damper assembly and flywheel sub-assembly.

·

Make sure that the front-rear direction of the transmission input damper assembly is correct when installing it.




Hide 30900 4.INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY

(See page Drivetrain>P510 (HYBRID TRANSMISSION / TRANSAXLE)>HYBRID VEHICLE TRANSAXLE>INSTALLATION)

NOTICE:

Be careful not to apply excess force to the transmission input damper assembly when removing or installing the hybrid vehicle transaxle assembly. If excess force is applied, the transmission input damper assembly may be damaged, or its splines may become misaligned.