Home › Engine / Hybrid System › 1NZ-FXE (ENGINE MECHANICAL) › ENGINE UNIT
RM2170E _51 Engine / Hybrid System _057005 1NZ-FXE ENGINE MECHANICAL _0277949 ENGINE UNIT G

1NZ-FXE ENGINE MECHANICAL  ENGINE UNIT  INSPECTION  


PROCEDURE

Hide 13506 1.INSPECT CHAIN SUB-ASSEMBLY

a.
A162995E16
0.67,1.772 0.766,1.920 0.096,0.148 10 0 0.824,1.772 0.920,1.920 0.096,0.148 10 1 0.989,1.772 1.085,1.920 0.096,0.148 10 2 1.141,1.772 1.236,1.920 0.096,0.148 10 3 1.304,1.772 1.400,1.920 0.096,0.148 10 4 1.458,1.772 1.553,1.920 0.096,0.148 10 5 1.71,1.205 1.863,1.353 0.153,0.148 10 *a 2.487,1.772 2.662,1.920 0.175,0.148 10 15 2.695,1.772 2.869,1.920 0.175,0.148 10 16

Using a spring scale, pull the chain sub-assembly with a force of 140 N (14.3 kgf, 31.5 lbf) and measure the length of it.

Text in Illustration
*a Measuring Area

Maximum length:

124.2 mm (4.89 in.)


If the length is greater than the maximum, replace the chain sub-assembly.

HINT:

Perform the measurement at 3 or more random places to obtain the average length.



Hide 13540 2.INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A011223E03
1.529,1.092 1.690,1.253 0.161,0.161 10 *1 1.145,0.964 1.331,1.187 1.331,1.187 1.51,1.187 false

Check that the plunger moves smoothly when the ratchet pawl is raised with your finger.

Text in Illustration
*1 Ratchet Pawl


b.

Release the ratchet pawl and check that the plunger is locked in place by the ratchet pawl and does not move when pushed with your finger.


Hide 13050 3.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

a.

Wrap the chain sub-assembly around the camshaft timing gear assembly.


b.
A037071

Using a vernier caliper, measure the diameter of the camshaft timing gear assembly with the chain sub-assembly.

Standard diameter:

97.4 mm (3.83 in.)


Minimum diameter:

96.2 mm (3.79 in.)


NOTICE:

The vernier caliper must come into contact with the chain rollers when measuring.


If the diameter is less than the minimum, replace the camshaft timing gear assembly.


Hide 13523 4.INSPECT CAMSHAFT TIMING GEAR OR SPROCKET

a.

Wrap the chain sub-assembly around the camshaft timing gear or sprocket.


b.
A037072

Using a vernier caliper, measure the diameter of the camshaft timing gear or sprocket with the chain sub-assembly.

Standard diameter:

97.4 mm (3.83 in.)


Minimum diameter:

96.2 mm (3.79 in.)


NOTICE:

The vernier caliper must come into contact with the chain rollers when measuring.


If the diameter is less than the minimum, replace the camshaft timing gear or sprocket.


Hide 13559 5.INSPECT CHAIN TENSIONER SLIPPER

a.
A037065

Measure the chain tensioner slipper wear.

Maximum wear:

1.0 mm (0.0394 in.)


If the wear is greater than the maximum, replace the chain tensioner slipper.


Hide 13561 6.INSPECT NO. 1 CHAIN VIBRATION DAMPER

a.
A037066

Measure the vibration damper wear.

Maximum wear:

1.0 mm (0.0394 in.)


If the wear is greater than the maximum, replace the No. 1 chain vibration damper.


Hide 11101A 7.INSPECT CYLINDER HEAD SET BOLT

a.
A199982E06
1.661,0.476 1.837,0.633 0.176,0.157 10 *a

Using a vernier caliper, measure the length of the cylinder head set bolts from the seat to the end.

Text in Illustration
*a Length

Standard length:

142.8 to 144.2 mm (5.62 to 5.68 in.)


Maximum length:

147.1 mm (5.79 in.)


If the length is greater than the maximum, replace the cylinder head set bolt.


Hide 17141 8.INSPECT EXHAUST MANIFOLD

a.
A268110

Using a precision straightedge and feeler gauge, measure the surface contacting the exhaust manifold for warpage.

Maximum warpage:

0.7 mm (0.0276 in.)


If the warpage is greater than the maximum, replace the exhaust manifold.