Home › Engine / Hybrid System › 1NZ-FXE (ENGINE MECHANICAL) › CYLINDER HEAD
RM2170E _51 Engine / Hybrid System _057005 1NZ-FXE ENGINE MECHANICAL _0277950 CYLINDER HEAD A

1NZ-FXE ENGINE MECHANICAL  CYLINDER HEAD  REPLACEMENT  


PROCEDURE

Hide 1.REPLACE STUD BOLT

HINT:

If any of the stud bolts is deformed or the threads are damaged, replace it.


a.

Using an E5 and E7 "TORX" socket wrench, replace the stud bolts.

U159005E03
1.198,0.698 0.781,0.698 false 3.073,3.104 3.073,3.469 3.073,3.469 0.833,3.469 false 1.146,3.125 1.146,3.458 false 4.177,1.021 4.177,1.531 4.177,1.531 6.198,1.531 false 6.031,0.979 6.031,1.521 false 4.135,2.677 4.135,3.292 4.135,3.292 6.167,3.292 false 5.979,2.677 5.979,3.281 false 5.365,4.073 5.49,4.219 0.125,0.146 10 false D 6.219,3.198 6.344,3.344 0.125,0.146 10 false D 0.896,3.844 1.021,3.99 0.125,0.146 10 false A 0.646,0.615 0.771,0.76 0.125,0.146 10 false A 2.385,3.969 2.51,4.115 0.125,0.146 10 false B 0.698,3.385 0.823,3.531 0.125,0.146 10 false B 3.875,3.813 4,3.958 0.125,0.146 10 false C 6.229,1.458 6.354,1.604 0.125,0.146 10 false C 1.177,0.292 1.344,0.458 0.167,0.167 10 false *a 1.01,1.656 1.177,1.823 0.167,0.167 10 false *c 1.354,4.417 1.521,4.583 0.167,0.167 10 false *e 2.833,4.385 3,4.552 0.167,0.167 10 false *h 3.167,4.667 3.333,4.833 0.167,0.167 10 false *i 4.354,4.292 4.521,4.458 0.167,0.167 10 false *j 4.677,4.688 4.844,4.854 0.167,0.167 10 false *l 5.833,4.552 6.031,4.719 0.198,0.167 10 false *m 6.167,4.771 6.365,4.938 0.198,0.167 10 false *n 4.365,5.271 4.531,5.438 0.167,0.167 10 false *k 5.833,5.167 6,5.333 0.167,0.167 10 false *f 1.667,4.646 1.844,4.896 0.177,0.25 10 false *g 1.375,5.167 1.542,5.333 0.167,0.167 10 false *f 2.833,5.094 3,5.26 0.167,0.167 10 false *f 4.01,2.01 4.177,2.177 0.167,0.167 10 false *d 4.073,0.292 4.24,0.458 0.167,0.167 10 false *b

Text in Illustration
*a Timing Chain Cover Side *b Intake Manifold Side
*c Upper Side *d Exhaust Manifold Side
*e 26.5 mm (1.04 in.) *f 12.0 mm (0.472 in.)
*g 43.5 mm (1.71 in.) *h 19.5 mm (0.768 in.)
*i 38.5 mm (1.52 in.) *j 28.5 mm (1.12 in.)
*k 13.0 mm (0.512 in.) *l 49.5 mm (1.95 in.)
*m 22.5 mm (0.886 in.) *n 37.5 mm (1.48 in.)

Torque:
Stud Bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
Stud Bolt B : 4.0 N*m (41 kgf*cm, 35 in.*lbf)
Stud Bolt C : 10 N*m (102 kgf*cm, 7 ft.*lbf)
Stud Bolt D : 9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 11151A 2.REPLACE STRAIGHT PIN

HINT:

If a straight pin is deformed or the threads are damaged, replace it.


a.

Remove the straight pins.


b.
A088732E04
1.75,2.344 2.729,2.573 0.979,0.229 10 true *a

Using a plastic hammer, tap in new straight pins to the specified protrusion height.

Text in Illustration
*a Standard Protrusion Height

Standard protrusion height:

4.5 to 5.5 mm (0.177 to 0.217 in.)



Hide 11122 3.REPLACE INTAKE VALVE GUIDE BUSH

a.
A088722

Heat the cylinder head to 80 to 100°C (176 to 212°F).


b.
A037110E06
1.469,0.271 1.813,0.469 0.344,0.198 10 true SST

Using SST and a hammer, tap out the intake valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


c.
A088723

Using a caliper gauge, measure the bush bore diameter of the cylinder head sub-assembly.

Standard bore diameter:
Bush size Specified Condition
STD 9.685 to 9.706 mm (0.381 to 0.382 in.)
O/S 0.05 9.735 to 9.756 mm (0.383 to 0.384 in.)


If the bush bore diameter of the cylinder head sub-assembly is greater than 9.706 mm (0.382 in.), machine the bush bore to the dimension of 9.735 to 9.756 mm (0.383 to 0.384 in.) to install an O/S 0.05 valve guide bush. If the bush bore diameter of the cylinder head is greater than 9.756 mm (0.384 in.), replace the cylinder head sub-assembly.


d.

Heat the cylinder head sub-assembly to 80 to 100°C (176 to 212°F).


e.
A390928E01
2.01,0.615 1.667,0.365 1.667,0.365 2.052,0.427 false 1.313,0.271 1.771,0.469 0.458,0.198 10 false SST 3.073,1.427 3.302,1.646 0.229,0.219 10 false *a

Using SST and a hammer, tap a new intake valve guide bush into the specified protrusion height.

Text in Illustration
*a Standard Protrusion Height

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard protrusion height:

9.0 to 9.4 mm (0.354 to 0.370 in.)



f.
A001447

Using a sharp 5 mm reamer, ream the intake valve guide bush to obtain the standard specified clearance between the intake valve guide bush and the valve stem.

Standard oil clearance:

0.025 to 0.060 mm (0.000984 to 0.00236 in.)



Hide 11126 4.REPLACE EXHAUST VALVE GUIDE BUSH

a.

Heat the cylinder head to 80 to 100°C (176 to 212°F).


b.
A265776E01
1.495,0.249 1.790,0.402 0.295,0.153 10 SST 1.14,0.411 1.448,0.343 1.448,0.343 1.179,0.663 false

Using SST and a hammer, tap out the exhaust valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


c.
A265777

Using a caliper gauge, measure the bush bore diameter of the cylinder head sub-assembly.

Standard bore diameter:
Bush size Specified Condition
STD 9.685 to 9.706 mm (0.381 to 0.382 in.)
O/S 0.05 9.735 to 9.756 mm (0.383 to 0.384 in.)


If the bush bore diameter of the cylinder head sub-assembly is greater than 9.706 mm (0.382 in.), machine the bush bore to the dimension of 9.735 to 9.756 mm (0.383 to 0.384 in.) to install an O/S 0.05 valve guide bush. If the bush bore diameter of the cylinder head is greater than 9.756 mm (0.384 in.), replace the cylinder head sub-assembly.


d.

Heat the cylinder head sub-assembly to 80 to 100°C (176 to 212°F).


e.
A265778E01
0.221,1.274 0.391,1.438 0.170,0.164 10 *a 1.694,0.214 2.005,0.364 0.311,0.150 10 SST 1.295,0.37 1.653,0.306 1.653,0.306 1.34,0.647 false

Using SST and a hammer, tap a new exhaust valve guide bush into the specified protrusion height.

Text in Illustration
*a Standard Protrusion Height

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard protrusion height:

9.0 to 9.4 mm (0.354 to 0.370 in.)



f.

Using a sharp 5 mm reamer, ream the exhaust valve guide bush to obtain the standard specified clearance between the exhaust valve guide bush and the valve stem.

Standard oil clearance:

0.030 to 0.065 mm (0.00118 to 0.00256 in.)