Home › Engine / Hybrid System › 1NZ-FXE (ENGINE MECHANICAL) › CYLINDER HEAD
RM2170E _51 Engine / Hybrid System _057005 1NZ-FXE ENGINE MECHANICAL _0277950 CYLINDER HEAD A

1NZ-FXE ENGINE MECHANICAL  CYLINDER HEAD  REASSEMBLY  


PROCEDURE

Hide 13734 1.INSTALL VALVE SPRING SEAT

a.

Install the 16 valve spring seats to the cylinder head sub-assembly.


Hide 2.INSTALL VALVE STEM OIL SEAL

a.
A267437E03
1.094,0.74 1.344,0.74 false 2.198,0.729 2.448,0.729 false 0.208,0.146 0.375,0.302 0.167,0.156 10 false *a 1.354,0.656 1.521,0.813 0.167,0.156 10 false *c 2,0.646 2.167,0.802 0.167,0.156 10 false *d 2.198,0.146 2.365,0.302 0.167,0.156 10 false *b

Apply a light coat of engine oil to a new valve stem oil seal.

Text in Illustration
*a Intake Side
*b Exhaust Side
*c Gray
*d Black

NOTICE:

Pay close attention when installing the intake and exhaust valve stem oil seals. For example, installing the intake valve stem oil seal to the exhaust side or installing the exhaust valve stem oil seal to the intake side can cause installation problems later.



b.
A265781E01
0.167,1.597 0.467,1.906 0.300,0.310 10 SST 0.555,2.329 0.725,2.480 0.170,0.151 10 *a 1.792,2.329 1.962,2.480 0.170,0.151 10 *b 0.54,1.684 0.771,1.684 0.771,1.684 1.152,1.246 false

Using SST, push on the 16 valve stem oil seals.

Text in Illustration
*a CORRECT
*b INCORRECT

SST
09201-41020  

NOTICE:

Failure to use SST will cause the seal to be damaged or improperly seated.



Hide 13711 3.INSTALL INTAKE VALVE

a.
A381428E02
2.646,1.531 2.958,1.729 0.313,0.198 10 false *a

Sufficiently apply engine oil to the tip area of the intake valve shown in the illustration.

Text in Illustration
*a 30 mm (1.18 in.) or more


b.

Install the 8 intake valves, 8 compression springs and 8 retainers to the cylinder head sub-assembly.

NOTICE:

Install the same parts in the same combination to their original locations.



c.
A265772E01
2.727,0.142 3.025,0.298 0.299,0.155 10 SST 1.846,0.766 2.387,0.226 2.387,0.226 2.698,0.226 false

Using SST and wooden blocks, compress the compression spring and install the 8 retainer locks.

SST
09202-70020  (09202-00010, 09202-01010, 09202-01020)


d.
A037146

Using a pin punch and plastic hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:

Be careful not to damage the valve stem tip.



Hide 13715 4.INSTALL EXHAUST VALVE

a.
A381429E02
2.646,1.625 2.958,1.823 0.313,0.198 10 false *a

Sufficiently apply engine oil to the tip area of the exhaust valve shown in the illustration.

Text in Illustration
*a 30 mm (1.18 in.) or more


b.

Install the 8 exhaust valves, 8 compression springs and 8 retainers to the cylinder head sub-assembly.

NOTICE:

Install the same parts in the same combination to their original locations.



c.
A265773E01
2.411,0.522 2.734,0.686 0.323,0.164 10 SST 1.822,0.612 2.391,0.612 false

Using SST and wooden blocks, compress the compression spring and install the 8 retainer locks.

SST
09202-70020  (09202-00010, 09202-01010, 09202-01020)


d.
A265782

Using a pin punch and plastic hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:

Be careful not to damage the valve stem tip.



Hide 13751 5.INSTALL VALVE LIFTER

a.

Apply a light coat of engine oil to the valve lifters.


b.
U158827

Install the 16 valve lifters.

NOTICE:

Install the same parts in the same combination to their original locations.



c.

Check that the valve lifters rotate smoothly by hand.


Hide 15678A 6.INSTALL OIL CONTROL VALVE FILTER

a.

Check that no foreign matter is on the mesh part of the oil control valve filter.


b.
A381430E02
2.167,1.292 2.375,1.042 2.375,1.042 2.583,1.042 false 2.615,0.958 2.844,1.156 0.229,0.198 10 false *a

Using an 8 mm hexagon wrench, install the oil control valve filter with a new gasket and the straight screw plug.

Text in Illustration
*a Mesh Part

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 11117A 7.INSTALL TAPER SCREW PLUG

a.

Install a new gasket to the taper screw plug.


b.
U158826

Using a 10 mm hexagon wrench, install the taper screw plug.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)