Home › Engine / Hybrid System › 1NZ-FXE (ENGINE MECHANICAL) › CYLINDER BLOCK
RM2170E _51 Engine / Hybrid System _057005 1NZ-FXE ENGINE MECHANICAL _0277951 CYLINDER BLOCK A

1NZ-FXE ENGINE MECHANICAL  CYLINDER BLOCK  REPLACEMENT  


PROCEDURE

Hide 1.REPLACE STUD BOLT

HINT:

If any of the stud bolts is deformed or the threads are damaged, replace it.


a.
A275766E01
1.742,3.039 1.914,3.194 0.172,0.155 10 *a 1.742,3.977 1.914,4.132 0.172,0.155 10 *a 2.1,3.487 2.272,3.642 0.172,0.155 10 *b

Using an E8 "TORX" socket wrench, replace the stud bolts.

Text in Illustration
*a 12.0 mm (0.472 in.)
*b 52.0 mm (2.05 in.)

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


Hide 11434A 2.REPLACE RING PIN

HINT:

If a ring pin is deformed or the threads are damaged, replace it.


a.

Remove the ring pins.


b.
A265801E01
1.392,2.016 1.551,2.169 0.159,0.153 10 *a 2.201,2.398 2.360,2.551 0.159,0.153 10 *b 0.705,2.482 0.864,2.634 0.159,0.153 10 *a

Using a plastic hammer, tap in the ring pins to the specified protrusion height.

Text in Illustration
*a 8.0 mm (0.315 in.)
*b 3.5 to 4.5 mm (0.138 to 0.177in.)


Hide 3.REPLACE STRAIGHT PIN

HINT:

If a straight pin is deformed or the threads are damaged, replace it.


a.

Remove the straight pins.


b.

Using a plastic hammer, tap in the straight pins to the specified protrusion height.

A268103E01
0.258,4.185 0.420,4.336 0.163,0.151 10 *a 1.048,0.262 1.211,0.413 0.163,0.151 10 *a 2.113,4.185 2.276,4.336 0.163,0.151 10 *b 3.86,4.185 4.023,4.336 0.163,0.151 10 *c 5.553,4.185 5.715,4.336 0.163,0.151 10 *d 4.2,0.262 4.363,0.413 0.163,0.151 10 *b 1.048,1.847 1.211,1.999 0.163,0.151 10 *c 4.2,1.847 4.363,1.999 0.163,0.151 10 *d 0.223,4.624 0.385,4.775 0.163,0.151 10 *e 2.052,4.585 2.215,4.736 0.163,0.151 10 *h 0.579,5.48 0.742,5.632 0.163,0.151 10 *f 2.441,5.48 2.604,5.632 0.163,0.151 10 *f 3.013,5.019 3.176,5.171 0.163,0.151 10 *i 3.82,4.622 3.982,4.773 0.163,0.151 10 *j 4.764,5.019 4.895,5.170 0.131,0.151 10 *l 4.166,5.427 4.329,5.578 0.163,0.151 10 *k 5.524,4.622 5.687,4.773 0.163,0.151 10 *j 6.468,5.019 6.599,5.170 0.131,0.151 10 *l 5.871,5.427 6.033,5.578 0.163,0.151 10 *k 1.154,5.018 1.317,5.170 0.163,0.151 10 *g

Text in Illustration
*a Timing Chain Cover Side *b Hybrid Vehicle Transaxle Side
*c Cylinder Head Side *d Oil Pan Side
*e 36.0 mm (1.42 in.) *f 10.0 mm (0.394 in.)
*g 18.5 to 19.5 mm (0.728 to 0.768 in.) *h 22.0 mm (0.866 in.)
*i 11.5 to 12.5 mm (0.453 to 0.492 in.) *j 18.0 mm (0.709 in.)
*k 8.0 mm (0.315 in.) *l 8.5 to 9.5 mm (0.335 to 0.374 in.)