Home › Engine / Hybrid System › 1NZ-FXE (ENGINE MECHANICAL) › CYLINDER BLOCK
RM2170E _51 Engine / Hybrid System _057005 1NZ-FXE ENGINE MECHANICAL _0277951 CYLINDER BLOCK A

1NZ-FXE ENGINE MECHANICAL  CYLINDER BLOCK  DISASSEMBLY  


PROCEDURE

Hide 1.INSPECT CONNECTING ROD THRUST CLEARANCE

a.
A084165

Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.

Standard thrust clearance:

0.16 to 0.36 mm (0.00630 to 0.0142 in.)


Maximum thrust clearance:

0.36 mm (0.0142 in.)


If the thrust clearance is greater than the maximum, replace the connecting rod.


Hide 2.INSPECT CRANKSHAFT THRUST CLEARANCE

a.
A084170

Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.

Standard thrust clearance:

0.04 to 0.24 mm (0.00157 to 0.00945 in.)


Maximum thrust clearance:

0.3 mm (0.0118 in.)


If the thrust clearance is greater than the maximum, replace the thrust washers as a set.

Reference
Item Thrust Washer Thickness Thrust Clearance
STD 2.43 to 2.48 mm (0.0957 to 0.0976 in.) 0.04 to 0.24 mm (0.00157 to 0.00945 in.)
O/S 0.125 2.493 to 2.543 (0.0981 to 0.100 in.) 0.04 to 0.24 mm (0.00157 to 0.00945 in.)
O/S 0.250 2.555 to 2.605 (0.101 to 0.103 in.) 0.04 to 0.24 mm (0.00157 to 0.00945 in.)


Hide 13201 3.REMOVE PISTON SUB-ASSEMBLY WITH CONNECTING ROD

a.
A001166

Using a ridge reamer, remove all carbon from the top of the cylinder.


b.

Mark each cylinder No. on the connecting rod and connecting rod cap with paint.


c.
A265787E01
0.368,0.257 0.674,0.410 0.306,0.153 10 SST 1.542,0.804 1.082,0.343 1.082,0.343 0.755,0.343 false

Using SST, remove the 2 connecting rod cap bolts.

SST
09205-16010  


d.
A270271

Using the 2 removed connecting rod cap bolts, remove the connecting rod cap with connecting rod bearing by wiggling the connecting rod cap right and left.


e.

Clean the crank pin and connecting rod bearing.

NOTICE:

Check the crank pin and connecting rod bearing for pitting and scratches.


HINT:

Keep the connecting rod bearing inserted in the connecting rod cap.



f.

Push the piston, connecting rod and connecting rod bearing through the top of the cylinder block.

HINT:
·

Keep each connecting rod bearing, connecting rod and connecting rod cap as a set.

·

Arrange the removed parts in the correct order.




Hide 13041 4.REMOVE CONNECTING ROD BEARING

a.

Remove the 8 connecting rod bearings.

HINT:

Arrange the removed parts in the correct order.



Hide 13011 5.REMOVE PISTON RING SET

a.
A084172

Using a piston ring expander, remove the No. 1 compression ring and No. 2 compression ring.


b.

Remove the oil ring and oil ring expander by hand.

HINT:

Arrange the removed parts in the correct order.



Hide 13101 6.REMOVE PISTON SUB-ASSEMBLY WITH PISTON PIN

a.
A380669E01
0.708,1.583 0.5,1.083 0.5,1.083 0.75,0.75 false 2.656,0.583 2.823,0.583 false 0.5,1.083 0.802,1.083 false 2.729,1.969 2.896,1.969 false 0.167,1.021 0.625,1.219 0.458,0.198 10 false SST 2.896,0.51 3.354,0.708 0.458,0.198 10 false SST 2.948,1.896 3.406,2.094 0.458,0.198 10 false SST

Using SST, press out the piston pin from the piston.

SST
09221-25026  (09221-00021, 09221-00030, 09221-00061, 09221-00090, 09221-00100)

HINT:
·

The piston and pin are a matched set.

·

Arrange the removed parts in the correct order.




Hide 13411 7.REMOVE CRANKSHAFT

a.
U158824E03
3.01,0.177 3.135,0.323 0.125,0.146 10 false 1 3,1.708 3.125,1.854 0.125,0.146 10 false 2 0.604,0.177 0.729,0.323 0.125,0.146 10 false 3 0.604,1.708 0.729,1.854 0.125,0.146 10 false 4 2.406,0.177 2.531,0.323 0.125,0.146 10 false 5 2.417,1.708 2.542,1.854 0.125,0.146 10 false 6 1.229,0.177 1.354,0.323 0.125,0.146 10 false 7 1.188,1.708 1.313,1.854 0.125,0.146 10 false 8 1.823,0.167 1.938,0.323 0.115,0.156 10 false 9 1.771,1.708 1.948,1.854 0.177,0.146 10 false 10

Using several steps, uniformly loosen and remove the 10 crankshaft bearing cap bolts with a 12 mm socket wrench for 12 pointed head in the sequence shown in the illustration.


b.
A270307

Using the 2 removed crankshaft bearing cap bolts, remove the 5 crankshaft bearing caps.

HINT:
·

Keep each No. 2 crankshaft bearing and crankshaft bearing cap as a set.

·

Arrange the removed parts in the correct order.




c.
A265794

Remove the crankshaft from the cylinder block.


Hide 11791 8.REMOVE UPPER CRANKSHAFT THRUST WASHER

a.
A265795

Remove the 2 upper crankshaft thrust washers from the cylinder block.

HINT:

Arrange the removed parts in the correct order.



Hide 11711 9.REMOVE CRANKSHAFT BEARING

a.
A265796

Remove the 5 upper crankshaft bearings from the cylinder block.

HINT:

Arrange the removed parts in the correct order.



b.
A198046

Remove the 5 lower crankshaft bearings from the crankshaft bearing cap.

HINT:

Arrange the removed parts in the correct order.



Hide 16261B 10.REMOVE WATER BY-PASS HOSE UNION

a.
A265797

Using a 17 mm deep socket wrench, remove the water by-pass hose union from the cylinder block.


Hide 13516B 11.REMOVE OIL JET

a.
A265798

Remove the oil jet from the cylinder block.