Home › Engine / Hybrid System › 1NZ-FXE FUEL › FUEL INJECTOR
RM2170E _51 Engine / Hybrid System _057006 1NZ-FXE FUEL _0277953 FUEL INJECTOR G

1NZ-FXE FUEL  FUEL INJECTOR  INSPECTION  


PROCEDURE

Hide 23250 1.INSPECT FUEL INJECTOR ASSEMBLY

a.

Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 11.6 to 12.4 Ω


If the result is not as specified, replace the fuel injector assembly.



b.

Inspect the injector injection volume.

CAUTION:

Keep the injector away from sparks during the test.


i.
A264971E13
0.5,1.667 0.729,1.896 0.729,1.896 0.833,1.896 false 0.844,0.896 1.135,0.604 1.135,0.604 1.25,0.604 false 1.979,1.292 2.281,1.594 2.281,1.594 2.406,1.594 false 2.646,0.688 2.948,0.385 2.948,0.385 3.063,0.385 false 0.865,1.813 1.042,1.99 0.177,0.177 10 false *1 1.302,0.542 1.479,0.719 0.177,0.177 10 false *2 2.448,1.531 2.625,1.708 0.177,0.177 10 false *3 3.125,0.323 3.302,0.5 0.177,0.177 10 false *4

Connect SST (fuel tube connector) to SST (hose) with SST (hose band), and then connect them to the fuel pipe (vehicle side).

Text in Illustration
*1 SST
(Hose)
*2 SST
(Hose Band)
*3 SST
(Fuel Tube Connector)
*4 Fuel Pipe (Vehicle Side)

SST
09268-31014  (09268-41500, 09268-41700, 95336-08070)


ii.

Install a new O-ring to the fuel injector.


iii.
A264972E13
1.333,0.125 0.958,0.125 false 1.74,0.323 2.031,0.323 false 1.302,0.74 0.969,0.74 false 1.5,1.021 1.667,1.021 false 2.104,1.375 2.448,1.375 false 1.333,1.896 0.99,1.896 false 0.771,0.042 0.938,0.219 0.167,0.177 10 false *1 2.094,0.25 2.26,0.427 0.167,0.177 10 false *2 0.771,0.677 0.938,0.854 0.167,0.177 10 false *3 1.708,0.958 1.875,1.135 0.167,0.177 10 false *4 2.5,1.281 2.667,1.458 0.167,0.177 10 false *5 0.771,1.813 0.938,1.99 0.167,0.177 10 false *6

Connect SST (adapter and hose) to the injector, and hold the injector and union with SST (clamp).

Text in Illustration
*1 SST
(Hose)
*2 SST
(Hose Band)
*3 SST
(Adapter)
*4 O-ring
*5 SST
(Clamp)
*6 Vinyl Tube

SST
09268-31014  (09268-41110, 09268-41300, 09268-41700, 95336-08070)


iv.

Install a vinyl tube onto the injector.

CAUTION:

Install a suitable vinyl tube onto the injector to contain any gasoline spray.



v.
A264974E09
1.948,0.417 2.479,0.417 false 2.125,1.406 2.49,1.406 false 1.25,0.375 0.76,0.375 false 0.542,0.302 0.729,0.479 0.188,0.177 10 false *1 2.552,0.333 2.74,0.51 0.188,0.177 10 false *2 2.552,1.313 2.74,1.49 0.188,0.177 10 false *3

Tie the clamp and adapter together with a tie band as shown in the illustration.

Text in Illustration
*1 SST
(Tie Band)
*2 SST
(Adapter)
*3 SST
(Clamp)

SST
09268-31014  (09268-41110, 09268-41300, 09268-41800)


vi.

Put the injector into a graduated cylinder.



viii.
A264973E14
2.031,0.552 2.031,0.969 false 1.969,1.021 2.125,1.26 0.156,0.24 10 false *1 1.052,1.354 1.208,1.594 0.156,0.24 10 false *a

Connect SST (wire) to the injector and the auxiliary battery for 15 seconds, and measure the injection volume with the graduated cylinder. Test each injector 2 or 3 times.

Text in Illustration
*1 SST
(Wire)
*a Connect

SST
09842-30080  

NOTICE:

Always switch the voltage on and off at the auxiliary battery side, not the injector side.


Standard Injection Volume:
Tester Connection Condition Specified Condition
Positive terminal - Ground terminal Per 15 seconds 47 to 58 cc (2.9 to 3.5 cu.in.)


Difference between each injector:

11 cc (0.6 cu.in.) or less


If the result is not as specified, replace the fuel injector assembly.



c.

Inspect for leaks.

i.

In the condition above, disconnect the tester probes of SST (wire) from the auxiliary battery and check for fuel drop from the injector.

Standard fuel drop:

1 drop or less per 12 minutes


If fuel drop is not as specified, replace the fuel injector assembly.