Home › Engine / Hybrid System › 1NZ-FXE FUEL › FUEL TANK › 2011.12–2017.06
RM2170E _51 Engine / Hybrid System _057006 1NZ-FXE FUEL _0277956 FUEL TANK A

1NZ-FXE FUEL  FUEL TANK  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

a.
A267872E02
2.427,1.667 2.563,1.802 2.563,1.802 2.646,1.802 false 2.677,1.719 2.885,1.927 0.208,0.208 10 false *1

When removing and installing the fuel tank assembly, arrange the inlet hose as shown in the illustration, and secure the fuel tank assembly using a cord or similar.

Text in Illustration
*1 Cord

NOTICE:

Depending on the arrangement of the inlet hose during removal, the inlet hose and rear suspension may interfere and cause fuel leaks.



Hide 77020A 2.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Hide 3.DRAIN FUEL

Hide 77310A 4.REMOVE FUEL TANK CAP ASSEMBLY

Hide 58156 5.REMOVE FRONT NO. 4 FLOOR HEAT INSULATOR

a.
A267873

Remove the 2 nuts and front No. 4 floor heat insulator.


Hide 77606 6.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

a.
A267874

Pinch and remove the clip as shown in the illustration.


b.

Remove the bolt and No. 1 fuel tank protector sub-assembly.


Hide 77262 7.DISCONNECT NO. 2 FUEL EMISSION TUBE

a.
A267876

Loosen the clip and disconnect the No. 2 fuel emission tube.


Hide 77266A 8.REMOVE NO. 1 FUEL TUBE PROTECTOR

a.
A268480E01
0.814,0.117 1.003,0.306 0.189,0.189 10 *1 1.661,0.736 1.135,0.211 1.135,0.211 1.021,0.211 false

Remove the No. 1 fuel tube protector from the fuel tube connector.

Text in Illustration
*1 No. 1 Fuel Tube Protector


Hide 77209F 9.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A388956E01
0.844,0.469 1.01,0.469 1.01,0.469 1.646,1.042 false 2.552,2.177 2.552,2.427 false 1.073,3.833 1.24,3.833 1.24,3.833 1.427,3.677 false 0.656,0.396 0.969,0.594 0.313,0.198 10 false *1 2.479,2.448 2.792,2.646 0.313,0.198 10 false *2 0.906,3.75 1.219,3.948 0.313,0.198 10 false *3

A388957E01
0.781,0.979 1.031,0.979 false 1.25,1.99 1.833,1.99 1.833,1.99 1.833,1.823 false 1.677,1.823 1.677,1.99 false 2.115,1.344 2.292,1.115 2.292,1.115 2.458,1.115 false 2.26,1.563 2.427,1.406 2.427,1.406 2.594,1.406 false 2.25,1.844 2.417,1.719 2.417,1.719 2.583,1.719 false 0.594,0.896 0.906,1.094 0.313,0.198 10 false *4 1.052,1.906 1.365,2.104 0.313,0.198 10 false *5 2.49,1.021 2.802,1.219 0.313,0.198 10 false *6 2.625,1.313 2.938,1.51 0.313,0.198 10 false *7 2.625,1.625 2.938,1.823 0.313,0.198 10 false *3

Pull the tabs of the retainer to disengage the lock claws and pull out the fuel tank main tube sub-assembly.

Text in Illustration
*1 Fuel Tank Main Tube Sub-assembly
*2 Fuel Tank Pipe Setting Holder
*3 Retainer
*4 Nylon Tube
*5 O-ring
*6 Fuel Tube Connector
*7 Fuel Pipe

NOTICE:
·

Check that there is no damage or foreign matter around the connecting parts of the fuel tube connector and fuel pipe before performing this work.

·

Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the fuel pipe.

·

Only disconnect the fuel tube connector by hand.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected part by covering it with a plastic bag after disconnecting the fuel tube connector.

·

If the fuel tube connector and fuel pipe are stuck, push and pull to release them.




b.

Disengage the 3 clamps and separate the fuel tank pipe setting holder.


Hide 77100 10.REMOVE FUEL TANK ASSEMBLY

a.
A267877E02
2.344,0.875 2.698,0.875 false 1.906,1.604 2.25,1.604 false 1.344,1.698 1.115,1.927 1.115,1.927 1.031,1.927 false 2.719,0.781 2.906,0.938 0.188,0.156 10 false *1 2.281,1.5 2.469,1.656 0.188,0.156 10 false *1 0.823,1.844 1.01,2 0.188,0.156 10 true *2

Disengage the 2 clamps and separate the air tube.

Text in Illustration
*1 Fuel Tank Filler Pipe Flange Plate
*2 Air Tube


b.

Remove the bolt.


c.

Disengage the claw and remove the fuel tank filler pipe flange plate.


d.
A267879

Support the fuel tank assembly using an engine lifter.


e.
A267878

Separate the 2 fuel hoses shown in the illustration.


f.
A267880

Remove the 4 bolts and fuel tank assembly.

NOTICE:
·

Slowly operate the engine lifter to lower the fuel tank.

·

Do not drop the fuel tank.




Hide 77701W 11.REMOVE NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY

a.
A267881

Disengage the clamp and remove the No. 1 canister outlet hose sub-assembly.


Hide 77281G 12.REMOVE FUEL HOSE CLAMP

a.
A267882

Remove the fuel hose clamp.


Hide 77209F 13.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A267883

Disengage the 2 clamps and remove the fuel tank main tube sub-assembly.


Hide 77262 14.REMOVE NO. 2 FUEL EMISSION TUBE

a.
A267884

Disengage the 2 clamps and remove the No. 2 fuel emission tube.


Hide 77217C 15.REMOVE NO. 2 FUEL TANK FILLER PIPE SUPPORT

a.
A267885

Disengage the clamp and remove the No. 2 fuel tank filler pipe support.


Hide 77216A 16.REMOVE NO. 1 FUEL TANK FILLER PIPE SUPPORT

a.
A267886

Disengage the clamp and remove the No. 1 fuel tank filler pipe support.