Home › Engine / Hybrid System › 1NZ-FXE INTAKE / EXHAUST › EXHAUST PIPE › 2011.12–2017.06
RM2170E _51 Engine / Hybrid System _057008 1NZ-FXE INTAKE / EXHAUST _0277970 EXHAUST PIPE A

1NZ-FXE INTAKE / EXHAUST  EXHAUST PIPE  INSTALLATION  


PROCEDURE

Hide 17410 1.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.
A077857

Using a vernier caliper, measure the free length of the compression springs.

Minimum 41.5 mm (1.64 in.)

HINT:

If the free length is less than minimum, replace the compression spring.



b.

Fully insert a new gasket to the exhaust manifold converter sub-assembly.


c.
A181728E17
1.074,0.399 1.283,0.621 0.209,0.223 10 *1 0.736,2.568 0.956,2.724 0.221,0.156 10 *2 2.726,1.902 2.949,2.042 0.223,0.140 10 *3 1.359,0.466 1.509,0.466 1.509,0.466 1.834,1.116 false 2.042,2.337 1.19,2.651 1.19,2.651 0.986,2.651 false 2.522,1.415 2.831,1.596 2.831,1.596 2.831,1.831 false

Using a plastic hammer and wooden block, tap in the new gasket until its surface is flush with the exhaust manifold.

Text in Illustration
*1 Exhaust Manifold Converter Sub-assembly
*2 Gasket
*3 Wooden Block

NOTICE:
·

Be careful with the installation direction of the gasket.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

Do not push in the gasket by using the exhaust pipe when connecting it.




d.

Connect the front exhaust pipe assembly to the 3 exhaust pipe supports.


e.

Install the front exhaust pipe assembly with the 2 bolts and 2 compression springs.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258941E01
0.543,0.102 0.692,0.251 0.149,0.149 10 *1 2.694,0.132 2.843,0.281 0.149,0.149 10 *3 0.605,1.113 0.754,1.263 0.149,0.149 10 *2 0.419,1.433 0.568,1.582 0.149,0.149 10 *a 1.146,0.584 0.883,0.184 0.883,0.184 0.733,0.184 false 0.79,1.195 0.925,1.195 0.925,1.195 1.112,0.903 false 2.411,0.76 2.503,0.215 2.503,0.215 2.676,0.215 false

After installation, check that the gaps between the flanges of the exhaust manifold and front exhaust pipe assembly are consistent front-to-rear and left-to-right.

Text in Illustration
*1 Exhaust Manifold
*2 Front Exhaust Pipe Assembly
*3 Gasket
*a Space between flanges: 8.5 mm (0.335 in.)



Hide 17430 2.INSTALL TAIL EXHAUST PIPE ASSEMBLY

a.
A077857

Using a vernier caliper, measure the free length of the compression springs.

Minimum 38.5 mm (1.52 in.)

HINT:

If the free length is less than minimum, replace the compression spring.



b.

Fully insert a new gasket to the front exhaust pipe assembly.


c.
A181728E17
1.074,0.399 1.283,0.621 0.209,0.223 10 *1 0.736,2.568 0.956,2.724 0.221,0.156 10 *2 2.726,1.902 2.949,2.042 0.223,0.140 10 *3 1.359,0.466 1.509,0.466 1.509,0.466 1.834,1.116 false 2.042,2.337 1.19,2.651 1.19,2.651 0.986,2.651 false 2.522,1.415 2.831,1.596 2.831,1.596 2.831,1.831 false

Using a plastic hammer and wooden block, tap in the new gasket until its surface is flush with the front exhaust pipe assembly.

Text in Illustration
*1 Front Exhaust Pipe Assembly
*2 Gasket
*3 Wooden Block

NOTICE:
·

Be careful with the installation direction of the gasket.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

Do not push in the gasket by using the exhaust pipe when connecting it.




d.

Connect the tail exhaust pipe assembly to the 2 exhaust pipe supports.


e.

Install the tail exhaust pipe assembly with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258966E01
0.714,0.328 0.870,0.476 0.156,0.148 10 *1 0.756,1.429 0.912,1.577 0.156,0.148 10 *2 2.843,0.368 2.999,0.516 0.156,0.148 10 *3 0.594,1.723 0.750,1.870 0.156,0.148 10 *a 1.366,0.938 1.095,0.404 1.095,0.404 0.9,0.404 false 1.329,1.162 1.13,1.515 1.13,1.515 0.94,1.515 false 2.248,0.916 2.621,0.448 2.621,0.448 2.827,0.448 false

After installation, check that the gaps between the flanges of the exhaust manifold and front exhaust pipe assembly are consistent front-to-rear and left-to-right.

Text in Illustration
*1 Tail Exhaust Pipe Assembly
*2 Front Exhaust Pipe Assembly
*3 Gasket
*a Space between flanges: 6.5 mm (0.256 in.)



Hide 3.INSPECT FOR EXHAUST GAS LEAK