Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › 2011.12–2014.12
RM2170E _51 Engine / Hybrid System _057012 CRUISE CONTROL _0277986 CRUISE CONTROL SYSTEM C

CRUISE CONTROL  CRUISE CONTROL SYSTEM  P0571  Brake Switch "A" Circuit  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly sends a signal to the power management control ECU. When the power management control ECU receives this signal, it cancels the cruise control. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light signal circuit. Cruise control cancellation occurs when voltage is applied to terminal STP. When the brake is applied, voltage is normally applied to terminal STP of the power management control ECU through the STOP fuse and the stop light switch assembly, and the power management control ECU turns the cruise control off.

DTC No. DTC Detection Condition Trouble Area
P0571 Voltage of STP signal and that of ST1- signal of power management control ECU are less than 1 V for 0.5 seconds or more
·

Stop light switch assembly

·

Stop light switch circuit

·

Power management control ECU



WIRING DIAGRAM

E248924E01
3.935,1.535 5.695,1.719 1.760,0.184 10 Stop Light Switch Assembly 3.524,1.885 4.856,2.069 1.332,0.184 10 to Skid Control ECU 3.636,1.535 3.915,1.679 0.279,0.144 10 A32 0.671,3.892 1.236,4.239 0.565,0.346 10 Auxiliary Battery 6.09,3.193 6.435,3.347 0.346,0.154 10 IG2D 5.767,3.965 7.067,4.276 1.299,0.311 10 Power Management Control ECU 5.45,3.966 5.715,4.124 0.265,0.159 10 A39 3.678,3.42 3.948,3.579 0.271,0.159 10 IG2 6.073,0.456 6.498,0.626 0.425,0.170 10 STP 2.446,0.609 2.872,0.780 0.425,0.170 10 STOP 0.556,3.338 0.973,3.490 0.417,0.152 10 MAIN 2.689,2.932 3.048,3.102 0.358,0.170 10 IG2 1.476,2.932 1.682,3.102 0.205,0.170 10 P/I 5.882,3.111 6.012,3.281 0.130,0.170 10 2 3.863,0.372 3.993,0.542 0.130,0.170 10 7 3.863,0.807 3.958,0.977 0.095,0.170 10 6 4.701,0.358 4.831,0.528 0.130,0.170 10 3 4.701,0.793 4.831,0.963 0.130,0.170 10 5 4.528,0.434 4.629,0.604 0.101,0.170 10 L 4.528,0.867 4.629,1.037 0.101,0.170 10 L 4.051,0.434 4.174,0.604 0.122,0.170 10 B 4.051,0.881 4.170,1.051 0.119,0.170 10 B 3.863,1.053 3.958,1.223 0.095,0.170 10 2 4.701,1.053 4.797,1.223 0.095,0.170 10 4 4.023,1.155 4.350,1.325 0.327,0.170 10 GND 4.355,1.085 4.682,1.255 0.327,0.170 10 ACC 2.327,1.053 2.971,1.223 0.644,0.170 10 IG2 NO. 2 0.554,1.476 1.056,1.646 0.502,0.170 10 DC/DC 5.808,0.362 6.029,0.532 0.221,0.170 10 23 5.878,0.795 5.980,0.965 0.102,0.170 10 7 6.073,0.883 6.498,1.053 0.425,0.170 10 ST1-

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK WIRE HARNESS AND CONNECTOR (STOP LIGHT SWITCH POWER SOURCE)
a.
U183695E01
1.531,0.291 1.803,0.446 0.272,0.156 10 A32 0.18,0.156 0.333,0.312 0.152,0.156 10 *a 0.988,1.72 1.317,1.876 0.329,0.156 10 GND 1.351,1.19 1.179,1.699 false 2.174,1.72 2.286,1.876 0.112,0.156 10 B 2.022,1.19 2.194,1.699 false 2.518,1.72 2.633,1.876 0.115,0.156 10 B 2.211,1.19 2.52,1.699 false

Disconnect the stop light switch assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A32-7 (B)- A32-2 (GND) Power switch off 11 to 14 V
A32-6 (B)- A32-2 (GND) Power switch on (IG) 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
A32-2 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.
U183694E01
1.539,0.411 1.812,0.567 0.272,0.156 10 A32 0.18,0.156 0.337,0.312 0.157,0.156 10 *a 0.809,1.72 0.908,1.876 0.099,0.156 10 L 1.168,1.72 1.486,1.876 0.318,0.156 10 ACC 1.586,1.127 0.909,1.703 false 2.223,1.72 2.551,1.876 0.328,0.156 10 GND 1.916,1.127 2.336,1.703 false 1.948,1.72 2.047,1.876 0.099,0.156 10 L 1.813,1.127 1.958,1.703 false 1.688,1.129 1.42,1.716 false

Reconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A32-3 (L) - A32-2 (GND) Power switch off, Brake pedal not depressed Below 1 V
A32-3 (L) - A32-2 (GND) Power switch off, Brake pedal depressed 11 to 14 V
A32-5 (L) - A32-2 (GND) Power switch on (IG), Brake pedal not depressed 11 to 14 V
A32-5 (L) - A32-2 (GND) Power switch on (IG), Brake pedal depressed Below 1 V
A32-4 (ACC) - A32-2 (GND) Power switch off 11 to 14 V


Text in Illustration
*a Component with harness connected
(Stop Light Switch Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the power management control ECU connector.


b.

Disconnect the stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A39-23 (STP) - A32-3 (L) Always Below 1 Ω
A39-7 (ST1-) - A32-5 (L) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A39-23 (STP) or A32-3 (L) - Body ground Always 10 kΩ or higher
A39-7 (ST1-) or A32-5 (L) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER MANAGEMENT CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)