Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › from 2014.12
RM2170E _51 Engine / Hybrid System _057012 CRUISE CONTROL _0277986 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the system to enter self-diagnostic mode. If a malfunction is present, cruise control indicator will blink.

HINT:

When a particular warning light remains blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in the relevant ECU is suspected.


WIRING DIAGRAM

E229592E24
5.552,1.01 5.771,1.167 0.219,0.156 10 false 28 5.844,1.115 6.063,1.271 0.219,0.156 10 false TC 3.594,1.969 4.74,2.135 1.146,0.167 10 false to Other Systems 1.021,3.271 1.406,3.417 0.385,0.146 10 false DLC3 0.75,3.271 0.969,3.417 0.219,0.146 10 false G4 5.344,3.281 7.135,3.51 1.792,0.229 10 false Hybrid Vehicle Control ECU 5,3.281 5.281,3.427 0.281,0.146 10 false G81 1.271,1.104 1.49,1.25 0.219,0.146 10 false TC 1.25,2.24 1.479,2.385 0.229,0.146 10 false CG 1.573,1 1.76,1.146 0.188,0.146 10 false 13 1.615,2.125 1.708,2.271 0.094,0.146 10 false 4

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TERMINAL TC of DLC3 - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the G81 hybrid vehicle control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
G81-28 (TC) - G4-13 (TC) Always Below 1 Ω




OK

2.CHECK HARNESS AND CONNECTOR (TERMINAL CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (DLC3 - HYBRID VEHICLE CONTROL ECU)

2.CHECK HARNESS AND CONNECTOR (TERMINAL CG of DLC3 - BODY GROUND)
C351650E03
2.156,0.292 2.542,0.531 0.385,0.24 1.563,1.073 1.188,0.688 false 0.115,0.083 0.615,0.323 0.5,0.24 10 false *a 0.948,0.583 1.448,0.823 0.5,0.24 10 false CG 2.24,0.323 2.74,0.563 0.5,0.24 10 false G4

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
G4-4 (CG) - Body ground Always Below 1 Ω


Text in Illustration
*a DLC3



OK

3.CHECK HARNESS AND CONNECTOR (TERMINAL TC of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (DLC3 - BODY GROUND)

3.CHECK HARNESS AND CONNECTOR (TERMINAL TC of DLC3 - BODY GROUND)
C351650E04
2.156,0.292 2.542,0.531 0.385,0.24 2.177,1.99 1.802,1.604 false 0.115,0.083 0.615,0.323 0.5,0.24 10 false *a 2.229,1.906 2.729,2.146 0.5,0.24 10 false TC 2.24,0.323 2.74,0.563 0.5,0.24 10 false G4

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
G4-13 (TC) - Body ground Always 10 kΩ or higher


Text in Illustration
*a DLC3



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR OR EACH ECU