Home › Drivetrain › P510 (HYBRID TRANSMISSION / TRANSAXLE) › SHIFT LEVER › 2011.12–2017.06
RM2170E _52 Drivetrain _057013 P510 HYBRID TRANSMISSION / TRANSAXLE _0277995 SHIFT LEVER G

P510 HYBRID TRANSMISSION / TRANSAXLE  SHIFT LEVER  INSPECTION  


PROCEDURE

Hide 33560C 1.INSPECT LOWER SHIFT LEVER ASSEMBLY

a.
C249921E07
1.094,0.635 1.167,0.635 1.167,0.635 1.667,0.99 false 1.604,1.833 1.667,1.833 1.667,1.833 1.698,1.094 false 0.896,0.552 1.083,0.698 0.188,0.146 10 false IG 0.198,0.042 0.385,0.188 0.188,0.146 10 false *a 1.271,1.75 1.583,1.896 0.313,0.146 10 false STP

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4 (IG) - Body ground Power switch on (IG) 11 to 14 V
Power switch off Below 1 V
8 (STP) - Body ground Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V


Text in Illustration
*a Component with harness connected
(Lower Shift Lever Assembly)

HINT:

Do not disconnect the lower shift lever assembly connector.



b.
C249921E08
1.677,1.792 1.74,1.792 1.74,1.792 1.771,1.052 false 0.198,0.042 0.385,0.188 0.188,0.146 10 false *a 1.552,1.698 1.677,1.844 0.125,0.146 10 false E

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (E) - Body ground Always Below 1 Ω


Text in Illustration
*a Component with harness connected
(Lower Shift Lever Assembly)

HINT:

Do not disconnect the lower shift lever assembly connector.



c.

Inspect shift lock solenoid

i.
C249922

Disconnect the shift lock solenoid connector.


ii.
C197452E19
1.365,1.208 0.615,1.583 true 1.594,1.219 1.365,1.615 true 1.833,1.219 2.125,1.594 true 2.083,1.219 2.771,1.594 true 0.094,0.063 0.385,0.333 0.292,0.271 10 false *a 0.448,1.615 0.823,1.823 0.375,0.208 10 false SLS+ 1.198,1.625 1.594,1.833 0.396,0.208 10 false SLS- 2.063,1.625 2.292,1.833 0.229,0.208 10 false E2 2.75,1.625 2.927,1.833 0.177,0.208 10 false P

Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

Standard Resistance:
Tester Connection Shift Lever Position Specified Condition
4 (P) - 3 (E2) P 10 kΩ or higher
Other than P Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Shift Lock Solenoid)

·

If the result is not as specified, replace the lower shift lever assembly.

·

If the shift lock does not operate when the power source of the lower shift lever assembly is normal and the resistance between the body ground and the shift lock solenoid is as specified, replace the lower shift lever assembly.



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SLS+) - 2 (SLS-) Always 112 Ω


·

If the result is not as specified, replace the lower shift lever assembly.

·

If the shift lock does not operate when the power source of the lower shift lever assembly is normal and the resistance between the body ground and the shift lock solenoid is as specified, replace the lower shift lever assembly.