Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY › 2011.12–2017.06
RM2170E _52 Drivetrain _057014 DRIVE SHAFT / PROPELLER SHAFT _0277996 FRONT DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY  DISASSEMBLY  


PROCEDURE

Hide 43448G 1.SEPARATE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

a.

for One Touch Type:

i.
C067083

Using a screwdriver, release the staked part of the front No. 2 axle inboard joint boot clamp and separate the front No. 2 axle inboard joint boot clamp as shown in the illustration.



b.

for Claw Engagement Type:

i.
C157518E03
0.807,1.147 1.000,1.310 0.192,0.162 10 *a 0.51,0.718 0.885,1.13 0.885,1.13 1.397,0.664 false

Using needle-nose pliers, disengage the 2 claws and remove the front No. 2 axle inboard joint boot clamp as shown in the illustration.

Text in Illustration
*a Claws



Hide 43448F 2.SEPARATE FRONT AXLE INBOARD JOINT BOOT CLAMP

HINT:

Perform the same procedure as for the front No. 2 axle inboard joint boot clamp.


Hide 3.SEPARATE INBOARD JOINT BOOT

a.

Separate the inboard joint boot from the front drive inboard joint assembly.


Hide 43040 4.REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY

a.

Remove the old grease from the front drive inboard joint assembly.


b.
C160821E13
0.918,0.354 1.095,0.531 0.177,0.177 10 *a 1.462,1.225 1.136,0.473 1.136,0.473 1.821,0.786 false

Put matchmarks on the front drive inboard joint assembly and front axle outboard joint shaft assembly.

Text in Illustration
*a Matchmark

NOTICE:

Do not use a punch for the marks.



c.

Remove the front drive inboard joint assembly from the front axle outboard joint shaft assembly.


d.

Secure the front axle outboard joint shaft assembly in a vise using aluminum plates.

NOTICE:

Do not overtighten the vise.



e.
C160822

Using a snap ring expander, remove the shaft snap ring from the front axle outboard joint shaft assembly.


f.
C162724E05
1.938,0.15 2.123,0.299 0.185,0.149 10 *a 2.997,0.587 2.997,0.239 2.997,0.239 2.162,0.239 false 2.914,0.517 2.914,0.239 false

Put matchmarks on the front axle outboard joint shaft assembly and tripod joint.

Text in Illustration
*a Matchmark

NOTICE:

Do not use a punch for the marks.



g.

Using a brass bar and a hammer, tap out the tripod joint from the front axle outboard joint shaft assembly.

NOTICE:
·

Do not tap the rollers.

·

Do not drop the tripod joint.




h.

Remove the front No. 2 axle inboard joint boot clamp, inboard joint boot and front axle inboard joint boot clamp.


Hide 43474A 5.SEPARATE DRIVE SHAFT DAMPER SETTING CLAMP (w/ 1 Clamp)

a.
U159313E01
2.094,3.03 2.111,3.049 0.018,0.019 2.017,3.105 2.036,3.123 0.019,0.018 2.093,3.181 2.11,3.2 0.018,0.019 2.168,3.106 2.187,3.124 0.019,0.018 2.918,2.876 2.936,2.895 0.018,0.019 2.842,2.951 2.861,2.969 0.019,0.018 2.917,3.026 2.935,3.045 0.018,0.019 2.992,2.952 3.011,2.97 0.019,0.018 0.125,2.373 0.429,2.606 0.304,0.232 10 *B 0.141,0.099 0.355,0.270 0.214,0.171 10 *A 2.18,3.143 2.474,3.227 2.474,3.227 2.849,2.992 false 2.38,3.217 2.548,3.355 0.168,0.137 10 *a

for One Touch Type:

i.

Using a screwdriver, release the staked part of the drive shaft damper setting clamp and separate the drive shaft damper setting clamp as shown in the illustration.

Text in Illustration
*A for One Touch Type
*B for Claw Engagement Type
*a Claws



b.

for Claw Engagement Type:

i.

Using needle-nose pliers, disengage the 2 claws and remove the drive shaft damper setting clamp as shown in the illustration.



Hide 43474 6.REMOVE DRIVE SHAFT DAMPER (w/ 1 Clamp)

a.

Remove the drive shaft damper and drive shaft damper setting clamp from the front axle outboard joint shaft assembly.


Hide 43474 7.SEPARATE DRIVE SHAFT DAMPER (w/ 2 Clamps)

a.
C205160E01
2.444,1.248 2.676,1.421 0.232,0.173 10 *a 2.663,0.648 2.529,1.238 2.529,1.238 1.843,0.853 false

Using needle-nose pliers, disengage the 2 claws and separate the 2 drive shaft damper setting clamps as shown in the illustration.

Text in Illustration
*a Claws


Hide 43474A 8.REMOVE DRIVE SHAFT DAMPER SETTING CLAMP (w/ 2 Clamps)

a.

Remove the drive shaft damper and 2 drive shaft damper setting clamps from the front axle outboard joint shaft assembly.


Hide 43447F 9.SEPARATE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP

a.
C249940

Using a screwdriver, release the staked part of the front No. 2 axle outboard joint boot clamp and separate the front No. 2 axle outboard joint boot clamp as shown in the illustration.


Hide 43447E 10.SEPARATE FRONT AXLE OUTBOARD JOINT BOOT CLAMP

HINT:

Perform the same procedure as for the front No. 2 axle outboard joint boot clamp.


Hide 11.REMOVE OUTBOARD JOINT BOOT

a.

Remove the front axle outboard joint boot clamp, outboard joint boot and front No. 2 axle outboard joint boot clamp from the front axle outboard joint shaft assembly.


b.

Remove the old grease from the outboard joint.


Hide 41336E 12.REMOVE FRONT DRIVE SHAFT DUST COVER

a.
F040647E33
1.958,0.833 2.417,0.375 false 2.49,0.281 2.823,0.448 0.333,0.167 10 false SST

Using SST and a press, remove the front drive shaft dust cover from the front drive inboard joint assembly.

SST
09950-00020  

NOTICE:

Do not drop the front drive inboard joint assembly.