Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › REAR WHEEL ALIGNMENT › 2015.11–2017.06
RM2170E _53 Suspension _057016 ALIGNMENT / HANDLING DIAGNOSIS _0278005 REAR WHEEL ALIGNMENT G

ALIGNMENT / HANDLING DIAGNOSIS  REAR WHEEL ALIGNMENT  INSPECTION  


CAUTION / NOTICE / HINT

NOTICE:

If the wheel alignment has been adjusted, or if suspension or underbody components have been removed/installed or replaced, be sure to perform the following initialization procedure in order for the system to function normally:

Perform zero point calibration of the yaw rate and acceleration sensor.



PROCEDURE

Hide 1. PRECAUTION

Standard values indicated by *1 and *2 in the specification tables are for the vehicles with a purple or blue identification mark on the bottom of the rear coil spring.

C253259E02
2.094,1.698 2.875,1.698 true 2.917,1.604 3.083,1.781 0.167,0.177 10 false *a

Text in Illustration
*a Colored identification mark on the bottom of the rear coil spring

Hide 4.INSPECT CAMBER

NOTICE:

Inspect while the vehicle is unloaded.


a.

Install a camber-caster-kingpin gauge.


b.

Inspect the camber.

Camber (Unloaded Vehicle):
Tire Size Camber Inclination Right-left Difference
175/65R15 -0°57' +/- 0°30' (-0.95° +/- 0.50°) 0°30' (0.50°) or less
185/60R15 -0°58' +/- 0°30' (-0.97° +/- 0.50°)
-0°55' +/- 0°30' (-0.92° +/- 0.50°) *1
-0°54' +/- 0°30' (-0.90° +/- 0.50°) *2


HINT:
·

*1: Vehicles with purple identification mark on the bottom of the rear coil spring

·

*2: Vehicles with blue identification mark on the bottom of the rear coil spring

·

Camber is not adjustable. If the measurement is not within the specified range, inspect the suspension parts for damage and/or wear, and replace them if necessary.




Hide 5.INSPECT TOE-IN

NOTICE:

Inspect while the vehicle is unloaded.


a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to N.


c.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)


d.
C188968E07
0.83,0.571 0.83,1.106 false 1.361,0.571 1.361,0.984 1.361,0.984 0.83,0.984 false 2.426,1.674 2.599,1.841 0.173,0.167 10 *b 0.734,1.117 0.896,1.277 0.161,0.160 10 *a 2.522,1.323 2.522,1.663 false

Put tread center marks on the rearmost points of the rear wheels and measure the distance between the marks (dimension B).

Text in Illustration
*a Tread Center Mark
*b Dimension B
V100135

Front of the Vehicle


e.

Slowly push the vehicle straight ahead to cause the rear wheels to rotate 180°. Use the rear tire valve as a reference point.

HINT:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from Step A again.



f.
C188969E07
0.556,1.641 0.727,1.801 0.172,0.160 10 *a 0.647,1.275 0.647,1.636 false 1.912,0.543 2.051,0.703 0.140,0.160 10 C 3.071,0.55 3.210,0.710 0.140,0.160 10 D 2.498,0.717 2.638,0.877 0.140,0.160 10 A 2.509,1.537 2.649,1.697 0.140,0.160 10 B

Measure the distance between the tread center marks on the front of the wheels (dimension A).

Text in Illustration
*a Dimension A
V100135

Front of the Vehicle

Toe-in (Unloaded Vehicle):
Tire Size Specified Condition Right-left Difference
175/65R15 C + D: 0°20' +/- 15' ( 0.33° +/- 0.25°) 30' (0.50°) or less
B - A: 3.9 +/- 3 mm (0.154 +/- 0.118 in.) 6.0 mm (0.236 in.) or less
185/60R15 C + D: 0°21' +/- 15' ( 0.35° +/- 0.25°)
C + D: 0°17' +/- 15' ( 0.28° +/- 0.25°) *1
C + D: 0°14' +/- 15' ( 0.23° +/- 0.25°) *2
30' (0.50°) or less
B - A: 3.9 +/- 3 mm (0.154 +/- 0.118 in.)
B - A: 3.2 +/- 3 mm (0.126 +/- 0.118 in.) *1
B - A: 2.8 +/- 3 mm (0.110 +/- 0.118 in.) *2
6.0 mm (0.236 in.) or less


HINT:
·

*1: Vehicles with purple identification mark on the bottom of the rear coil spring

·

*2: Vehicles with blue identification mark on the bottom of the rear coil spring

·

Measure "B - A" only when "C + D" cannot be measured.



If the toe-in is not within the specified range, inspect the suspension parts and replace them if necessary.


Hide 6. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 7. PERFORM YAW RATE AND ACCELERATION SENSOR CALIBRATION