Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL(for RHD)
RM2170E _54 Brake _057022 BRAKE SYSTEM (OTHER) _0278028 BRAKE PEDAL(for RHD) N

BRAKE SYSTEM (OTHER)  BRAKE PEDAL(for RHD)  ADJUSTMENT  


PROCEDURE

Hide 1.INSPECT AND ADJUST BRAKE PEDAL HEIGHT

a.

Check the brake pedal height.

i.

Turn back the carpet.


ii.

Turn back the dash silencer from the slit provided on the dash silencer.


iii.

Measure the shortest distance between the brake pedal pad surface and floor panel as shown in the illustration.

C256180E01
3.902,1.53 4.081,1.675 0.179,0.145 10 *a 2.006,1.468 2.170,1.612 0.164,0.145 10 *1 2.381,1.534 2.158,1.534 false

Text in Illustration
*1 Brake Pedal - -
*a Brake Pedal Height - -
V100144

Measuring Plane of Floor Panel - -

Pedal height from floor panel:

107.3 to 117.3 mm (4.23 to 4.61 in.)


If the pedal height is incorrect, adjust it.



b.

Adjust the brake pedal height.

i.
C249833E01
2.605,1.083 2.763,1.242 0.159,0.159 10 *1 0.95,2.019 1.109,2.177 0.159,0.159 10 *2 1.017,3.907 1.175,4.066 0.159,0.159 10 *3 2.176,1.17 2.605,1.17 false 1.34,1.691 1.34,2.107 1.34,2.107 1.125,2.107 false 1.756,3.768 1.534,3.991 1.534,3.991 1.192,3.991 false 2.373,3.685 2.526,3.826 0.153,0.141 10 *a

Remove the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL).

Text in Illustration
*1 Stop Light Switch Assembly
*2 Clevis Lock Nut
*3 Floor Panel
*a Brake Pedal Height


ii.

Loosen the clevis lock nut.


iii.

Adjust the brake pedal height by turning the push rod.

Pedal height from floor panel:

107.3 to 117.3 mm (4.23 to 4.61 in.)



iv.

Tighten the clevis lock nut.

Torque:
26 N*m (260 kgf*cm, 19 ft.*lbf)


v.

Install and adjust the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION).



Hide 89510D 2.INSPECT AND ADJUST BRAKE PEDAL STROKE SENSOR ASSEMBLY

a.
C249818

Loosen the 2 bolts.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the intelligent tester on and enter the following menus: Chassis / ABS/VSC/TRC / Data List "Stroke Sensor".


e.
C249817

Read the stroke sensor value in the Data List, and turn the brake pedal stroke sensor assembly slowly to the right or left to adjust the output voltage so that it is within the following range.

Standard voltage (without the brake pedal depressed):

0.8 to 1.2 V



f.
C249818

Tighten the 2 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:

Do not depress the brake pedal after turning the power switch on (IG).



g.

Turn the intelligent tester off and turn the power switch off.


h.

Disconnect the intelligent tester.


Hide 3.INSPECT BRAKE PEDAL FREE PLAY

a.
C132708E18
2.146,1.552 2.313,1.729 0.167,0.177 10 false *a

Depress the pedal until a slight resistance is felt. Measure the brake pedal free play as shown in the illustration.

Text in Illustration
*a Brake Pedal Free Play

Pedal free play:

1.0 to 6.0 mm (0.0394 to 0.236 in.)


If the pedal free play is not as specified, check the stop light switch clearance (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION). If the pedal free play is as specified, proceed to the Inspect Brake Pedal Reserve Distance procedure.


Hide 4.INSPECT BRAKE PEDAL RESERVE DISTANCE

a.

Release the parking brake.


b.

With the power switch on (READY), depress the brake pedal and measure the pedal reserve distance as shown in the illustration.

C256184E01
3.857,1.498 4.027,1.653 0.170,0.154 10 *a 2.725,1.962 2.892,2.107 0.167,0.145 10 *1 2.794,1.607 2.794,1.962 false

Text in Illustration
*1 Brake Pedal - -
*a Brake Pedal Reserve Distance - -
V100144

Measuring Plane of Floor Panel - -

Pedal reserve distance from the floor panel at 294 N (30 kgf, 66.1 lbf):

More than 70 mm (2.76 in.)


If the distance is not as specified, troubleshoot the brake system (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).


Hide 5. PERFORM INITIALIZATION AND CALIBRATION OF LINEAR SOLENOID VALVE