Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL(for LHD)
RM2170E _54 Brake _057022 BRAKE SYSTEM (OTHER) _0278033 BRAKE PEDAL(for LHD) N

BRAKE SYSTEM (OTHER)  BRAKE PEDAL(for LHD)  ADJUSTMENT  


PROCEDURE

Hide 1.INSPECT AND ADJUST BRAKE PEDAL HEIGHT

a.

Check the brake pedal height.

i.

Turn back the carpet.


ii.

Turn back the dash silencer from the slit provided on the dash silencer.


iii.

Measure the shortest distance between the brake pedal surface and floor panel or No. 2 dash panel insulator pad as shown in the illustration.

C256181E01
3.232,2.429 3.400,2.597 0.167,0.167 10 *a 2.34,1.318 2.507,1.486 0.167,0.167 10 *1 2.945,1.392 2.492,1.392 false

Text in Illustration
*1 Brake Pedal - -
*a Brake Pedal Height - -
V100144

Measuring Plane of Floor Panel or No. 2 Dash Panel Insulator Pad - -

Brake Pedal Height:
Condition Specification
from floor panel 131.2 to 141.2 mm (5.17 to 5.55 in.)
from No. 2 dash panel insulator pad 107.3 to 117.3 mm (4.23 to 4.61 in.)


If the pedal height is incorrect, adjust it.



b.

Adjust the brake pedal height.

i.
C250006E01
2.592,0.775 2.751,0.934 0.159,0.159 10 *1 0.408,1.678 0.567,1.837 0.159,0.159 10 *2 0.68,3.919 0.839,4.079 0.159,0.159 10 *3 2.165,0.868 2.592,0.868 false 1.129,1.366 0.731,1.764 0.731,1.764 0.582,1.764 false 1.255,3.786 1.025,4.016 1.025,4.016 0.86,4.016 false 0.936,4.261 1.095,4.421 0.159,0.159 10 *4 1.654,3.986 1.282,4.358 1.282,4.358 1.117,4.358 false 2.013,3.598 2.173,3.741 0.159,0.144 10 *a 2.503,3.721 2.662,3.865 0.159,0.144 10 *b

Remove the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL).

Text in Illustration
*1 Stop Light Switch Assembly
*2 Clevis Lock Nut
*3 Floor Panel
*4 No. 2 Dash Panel Insulator Pad
*a Brake Pedal Height from Floor Panel
*b Brake Pedal Height from No. 2 Dash Panel Insulator Pad


ii.

Loosen the clevis lock nut.


iii.

Adjust the brake pedal height by turning the push rod.

Brake Pedal Height:
Condition Specification
from floor panel 131.2 to 141.2 mm (5.17 to 5.55 in.)
from No. 2 dash panel insulator pad 107.3 to 117.3 mm (4.23 to 4.61 in.)



iv.

Tighten the clevis lock nut.

Torque:
26 N*m (260 kgf*cm, 19 ft.*lbf)


v.

Install and adjust the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION).



Hide 89510D 2.INSPECT AND ADJUST BRAKE PEDAL STROKE SENSOR ASSEMBLY

a.
C249997

Loosen the 2 bolts.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the intelligent tester on and enter the following menus: Chassis / ABS/VSC/TRC / Data List "Stroke Sensor".


e.
C249996

Read the stroke sensor value in the Data List, and turn the brake pedal stroke sensor assembly slowly to the right or left to adjust the output voltage so that it is within the following range.

Standard voltage (without the brake pedal depressed):

0.8 to 1.2 V



f.
C249997

Tighten the 2 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:

Do not depress the brake pedal after turning the power switch on (IG).



g.

Turn the intelligent tester off and turn the power switch off.


h.

Disconnect the intelligent tester.


Hide 3.INSPECT BRAKE PEDAL FREE PLAY

a.
C132708E18
2.146,1.552 2.313,1.729 0.167,0.177 10 false *a

Depress the pedal until a slight resistance is felt. Measure the brake pedal free play as shown in the illustration.

Text in Illustration
*a Brake Pedal Free Play

Pedal free play:

1.0 to 6.0 mm (0.0394 to 0.236 in.)


If the pedal free play is not as specified, check the stop light switch clearance (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION). If the pedal free play is as specified, proceed to the Inspect Brake Pedal Reserve Distance procedure.


Hide 4.INSPECT BRAKE PEDAL RESERVE DISTANCE

a.

Release the parking brake.


b.

With the power switch on (READY), depress the brake pedal and measure the pedal reserve distance as shown in the illustration.

C256185E01
2.218,1.577 2.392,1.728 0.174,0.151 10 *a 3.065,1.699 3.239,1.850 0.174,0.151 10 *1 3.129,1.588 3.129,1.699 false

Text in Illustration
*1 Brake Pedal - -
*a Brake Pedal Reserve Distance - -
V100144

Measuring Plane of Floor Panel - -

Brake pedal reserve distance from the floor panel at 294 N (30 kgf, 66.1 lbf):

More than 70 mm (2.76 in.)


If the distance is not as specified, troubleshoot the brake system (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).


Hide 5. PERFORM INITIALIZATION AND CALIBRATION OF LINEAR SOLENOID VALVE