Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM › from 2014.12
RM2170E _55 Steering _057027 STEERING COLUMN _0278046 STEERING LOCK SYSTEM U

STEERING COLUMN  STEERING LOCK SYSTEM  DATA LIST / ACTIVE TEST  


READ DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Turn the power switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the intelligent tester on.


e.

Enter the following menus: Body / (desired system) / Data List.


f.

According to the display on the intelligent tester, read the Data List.


g.

Using the intelligent tester, confirm the Data List items to help determine the cause of the problem.

NOTICE:
·

The steering lock ECU communicates with the intelligent tester through the certification ECU (smart key ECU assembly) which uses CAN communication. If the CAN communication system or certification ECU (smart key ECU assembly) is malfunctioning, Data List items may not be normal.

·

When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle and select "Manual" from the initial screen on the intelligent tester. Select "Key Code Registration" under model code.



Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Shift P Signal Shift position (P) signal / ON or OFF ON: Shift lever in P
OFF: Shift lever not in P
·

Use this item to determine if the shift position switch is malfunctioning.

·

The hybrid control system cannot be started when this item is "OFF".


Steering Unlock Switch State of steering unlock sensor signal output from steering lock actuator assembly / ON or OFF ON: Steering unlocked (Power switch on (ACC))
OFF: Steering locked (Power switch off door opened)
This item can be used to determine the cause of problems when the steering does not lock or unlock.
HINT:
·

The steering is considered locked when the lock sensor is ON and the unlock sensor is OFF.

·

The steering is considered unlocked when the lock sensor is OFF and the unlock sensor is ON.



Str Lock/Unlock Wait T-Out Steering lock or unlock malfunction / Yes or No Yes: Steering lock/unlock timed out (Lock bar stuck, etc.)
No: Steering locks/unlocks normally within specified time
The hybrid control system cannot be started when this item is "Yes".

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Ignition Switch State of certification ECU (smart key ECU assembly) IG power supply input / ON or OFF ON: Power switch on (IG)
OFF: Power switch off
This item displays "OFF" when the power switch is on (ACC).
#Codes Number of DTCs / 0 to 255 Number of stored DTCs displayed -
Immobiliser State of immobiliser system determined by certification ECU (smart key ECU assembly) / Set or Unset Set: Engine immobiliser set (Power switch off)
Unset: Engine immobiliser unset (Power switch on (ACC) or on (IG))
·

When the immobiliser cannot be unset, this item can be used to determine whether the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is part of the problem.

·

The hybrid control system cannot be started when this item displays "Set".


HINT:
·

The state of the immobiliser (whether it is set or unset) can be determined through the certification ECU (smart key ECU assembly). If this item displays "Set", the communication between the certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) can be determined to be normal.

·

The security indicator light operation is only linked with the state of the immobiliser (set/unset), and is not related to the steering lock operation (lock/unlock), when the immobiliser is set, the security indicator light blinks.



Steering Lock Sleep Cond Steering lock ECU sleep condition / Yes or No - -
Steering Lock Start Cond Transmission state of steering lock ECU wake up signal / Yes or No Yes: Wake up signal transmitted
No: Wake up signal not transmitted
-
Engine Start Condition State of hybrid control system permission signal determined by steering lock ECU and sent to certification ECU (smart key ECU assembly) / OK or NG OK: Hybrid control system permitted
NG: Hybrid control system prohibited
·

When this item displays "OK", the certification ECU (smart key ECU assembly) has received an unlock confirmation signal from the steering lock ECU and has permitted fuel injection and hybrid control system combustion.

·

The hybrid control system cannot be started when this item displays "NG".


Sensor Value Record of malfunction of position sensor in steering lock actuator assembly / OK or NG(Past) OK: No record of lock/unlock sensor malfunction in steering lock actuator assembly
NG(Past): Record of lock/unlock sensor in steering lock actuator assembly turning ON at same time exists
When this item displays "NG", the sensor inside the steering lock actuator assembly may be malfunctioning, or there may be a mechanical malfunction.
Power Supply Short Record of malfunction of signal sent to steering lock motor (steering lock actuator assembly) from certification ECU (smart key ECU assembly) (short circuit) / OK or NG(Past) OK: No record of malfunction (short circuit)
NG(Past): Record of malfunction (short circuit) exists
This item records malfunctions in the circuit between the certification ECU (smart key ECU assembly) and steering lock motor (steering lock actuator assembly).
Motor Driver Short Record of malfunction of motor activation circuit in steering lock actuator assembly (short circuit) (DTC B2781 stored) / OK or NG(Past) OK: No record of malfunction (short circuit)
NG(Past): Record of malfunction (short circuit) exists
This item records malfunctions in the motor activation circuit inside the steering lock actuator assembly (short circuit).
Lock/Unlock Receive Reception state of steering lock or unlock request signal from certification ECU (smart key ECU assembly) / Yes or No Yes: Record of receiving lock or unlock request signal exists
No: No record of receiving lock or unlock request signal
-
Lock Bar Stuck Error Record of lock bar not properly unlocking after being commanded to unlock for certain amount of time / OK or NG(Past) OK: No record of stuck lock bar
NG(Past): Record of stuck lock bar exists
-
Push Start Error Record of malfunction of push-start function due to steering lock actuator assembly / OK or NG(Past) OK: No record of push-start function malfunction
NG(Past): Record push-start function malfunction exists
-
Engine Start Request Reception state of hybrid control system permission signal determined by steering lock actuator assembly and sent to certification ECU (smart key ECU assembly) / OK or NG OK: Receiving signal
NG: Not receiving signal
·

When this item displays "OK", the certification ECU (smart key ECU assembly) has received an unlock confirmation signal from the steering lock ECU and has permitted fuel injection and hybrid control system combustion.

·

The hybrid control system cannot be started when this item displays "NG".


S Code Check Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) / OK or NG OK: Verification result normal
NG: Verification result abnormal
When a malfunction is present:
·

The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the hybrid control system cannot be started).


L Code Check Verification result between ID code box (immobiliser code ECU) and steering lock ECU / OK or NG OK: Verification result normal
NG: Verification result abnormal
When a malfunction is present:
·

The ID code for the ID code box (immobiliser code ECU) or steering lock ECU is not registered or the ID code box (immobiliser code ECU) or steering lock ECU is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the hybrid control system cannot be started).


Unlock Request Receive Reception state of steering unlock request signal by certification ECU (smart key ECU assembly) and sent to ID code box (immobiliser code ECU) / OK or NG
HINT:
·

The reception state is maintained for 10 seconds.

·

When 10 seconds or more elapse after receiving the signal, the item changes to "NG".



OK: Within 10 seconds of turning power switch on (IG) or on (ACC) or starting hybrid control system
NG: Except above
·

If the unlock signal has not been received, the hybrid control system cannot be started.

·

If this item does not change to "OK" even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.


Lock Request Receive Reception state of steering lock request signal by certification ECU (smart key ECU assembly) and sent to ID code box (immobiliser code ECU) / OK or NG
HINT:
·

The reception state is maintained for 10 seconds.

·

When 10 seconds or more elapse after receiving the signal, the item changes to "NG".



OK: Within 10 seconds of opening any door with power switch off and shift lever in P
NG: Except above
If this item does not change to "OK" even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.
S Code Check(Past) Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) (Past) / OK or NG(Past) OK: Verification result normal
NG(Past): Verification result abnormal (Past)
-
L Code Check(Past) Verification result between ID code box (immobiliser code ECU) and steering lock ECU (Past) / OK or NG(Past) OK: Verification result normal
NG(Past): Verification result abnormal (Past)
-
Steering Lock State of whether steering lock ECU has determined steering is locked / Set or Unset Set: Steering locked
Unset: Steering unlocked
If this item displays "Unset", the steering does not lock.
Steering Unlock State of whether steering lock ECU determined steering is unlocked / Set or Unset Set: Steering unlocked
Unset: Steering locked
If this item displays "Unset", the steering does not unlock (hybrid control system cannot be started).

HINT:

Unlock operation conditions for the steering lock:

When the following condition is met, the unlock operation is performed:

The power switch is on (ACC) or on (IG).

·

When the power switch is turned on (ACC) or on (IG) and the key and certification ECU (smart key ECU assembly) are verified, the steering is unlocked.


When any of the following conditions are met, key verification is performed.

·

The brake pedal is depressed so that the hybrid control system can be started.

·

30 seconds elapse after opening and closing a door.

·

The power switch is pressed.


Key verification occurs when the code emitted from the key and the code stored in the certification ECU (smart key ECU assembly) are compared to check that they match.

Certification ECU (smart key ECU assembly) verification occurs when the S code and L code are verified while the hybrid control system is being started or the power switch is being pushed. The ID code box (immobiliser code ECU) uses the S code to determine whether the certification ECU (smart key ECU assembly) is authorized. The steering lock ECU uses the L code to determine whether the ID code box (immobiliser code ECU) is authorized.

Lock operation conditions for the steering:

When the following conditions are met and the certification ECU (smart key ECU assembly) has been verified, the lock operation is performed.

·

The power switch is off.

·

The shift lever is in P.

·

A door is opened or a door lock operation (smart door lock, wireless door lock or key-linked lock) is performed.



HINT:

The following example shows the behavior of various Data List items when the shift lever is in P, the brake pedal is not depressed, the vehicle is normal and the power source mode changes.


C240209E07
0.689,1.253 1.676,1.443 0.988,0.190 10 Ignition Switch 0.476,2.19 1.941,2.399 1.465,0.209 10 Engine Start Condition 0.532,3.119 1.959,3.328 1.426,0.209 10 Engine Start Request 0.434,4.066 2.016,4.256 1.582,0.190 10 Unlock Request Receive 0.482,5.009 1.966,5.218 1.485,0.209 10 Lock Request Receive 0.725,5.897 1.667,6.107 0.942,0.209 10 Steering Lock 0.7,6.734 1.778,6.943 1.077,0.209 10 Steering Unlock 2.369,2.034 2.644,2.263 0.275,0.229 10 OK 2.369,2.355 2.644,2.583 0.275,0.229 10 NG 2.369,1.106 2.644,1.277 0.275,0.171 10 ON 2.369,1.428 2.683,1.618 0.313,0.190 10 OFF 2.369,3.908 2.663,4.137 0.294,0.229 10 NG 2.369,4.243 2.663,4.472 0.294,0.229 10 OK 2.369,4.854 2.663,5.083 0.294,0.229 10 NG 2.369,5.168 2.644,5.397 0.275,0.229 10 OK 2.369,2.956 2.625,3.184 0.255,0.229 10 NG 2.369,3.297 2.644,3.526 0.275,0.229 10 OK 2.369,5.786 2.663,5.956 0.294,0.171 10 Set 2.369,6.008 2.822,6.199 0.452,0.190 10 Unset 2.369,6.612 2.683,6.783 0.314,0.171 10 Set 2.369,6.863 2.822,7.053 0.452,0.190 10 Unset 3.329,0.655 3.511,0.820 0.183,0.166 10 *1 3.795,0.655 3.978,0.820 0.183,0.166 10 *2 4.857,0.655 5.040,0.820 0.183,0.166 10 *3 5.346,0.655 5.528,0.820 0.183,0.166 10 *4 0.357,0.237 4.397,0.409 4.040,0.172 10 Steering Lock Data List Display During Power Switch Operation

HINT:
Get into the vehicle while carrying the key. With the power switch off, the shift lever in P and all the doors closed, perform the following procedures and check the power source mode.

*1: Without depressing the brake pedal, press the power switch and check that the power source mode changes to on (ACC).

*2: Without depressing the brake pedal, press the power switch and check that the power source mode changes to on (IG).

*3: Press the power switch and check that the power source mode changes off.

*4: Release the brake pedal, open the driver door and check that the steering locks.


Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Door Courtesy*5 Front door courtesy light switch assembly RH / CLOSE or OPEN CLOSE: Front door RH closed
OPEN: Front door RH open
If this item does not change according to the actual state of the driver door, there is a malfunction in the door courtesy light switch or related part.
FL Door Courtesy*6 Front door courtesy light switch assembly LH / CLOSE or OPEN CLOSE: Front door LH closed
OPEN: Front door LH open
If this item does not change according to the actual state of the driver door, there is a malfunction in the door courtesy light switch or related part.

*5: for RHD

*6: for LHD



ACTIVE TEST


HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Turn the power switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the intelligent tester on.


e.

Enter the following menus: Body / (desired system) / Active Test.


f.

According to the display on the intelligent tester, perform the Active Test.



Power Source Control
Tester Display Test Part Control Range Diagnostic Note
P Supply for Steering Lock Certification ECU (smart key ECU assembly) ON/OFF
HINT:

ON: Power is supplied

OFF: Power is not supplied


When performing this Active Test, make sure the following condition is met:
The power switch is on (IG).