Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2011.12–2014.12
RM2170E _57 Power Source / Network _057033 NETWORKING _0278068 CAN COMMUNICATION SYSTEM U

NETWORKING  CAN COMMUNICATION SYSTEM  TERMINALS OF ECU  


NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Turn the power switch off before measuring the resistances between CAN main bus lines and between CAN branch lines.

·

Turn the power switch off before inspecting CAN bus lines for a ground short.

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

This section describes the standard values for all CAN related components.



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



CAN JUNCTION CONNECTOR LH (for LHD)


HINT:

The following tables contain information about the items and buses connected via junction connectors. The junction connector may be used for multiple separate buses. In this case, the name of the bus will be shown below the name of the item that the terminals are connected to. The bus name will be shown in brackets (example: (for Sub bus 15)).


a.

Check the CAN junction connector LH (instrument panel wire side) (for V bus).

i.

Connection diagram

U183584E01
2.105,1.175 2.663,1.337 0.557,0.162 10 CANH*b 2.125,2.066 2.662,2.222 0.537,0.156 10 CANL*b 3.495,0.372 3.778,0.526 0.283,0.153 10 G71 3.027,1.667 3.027,1.248 3.027,1.248 2.66,1.248 false 2.222,0.866 2.780,1.028 0.557,0.162 10 CANH*c 4.418,1.124 4.976,1.285 0.557,0.162 10 CANH*f 4.418,2.07 4.976,2.232 0.557,0.162 10 CANL*f 3.144,1.669 3.144,0.939 3.144,0.939 2.776,0.939 false 3.51,1.669 3.51,1.194 3.51,1.194 4.393,1.194 false 4.298,0.852 4.856,1.014 0.557,0.162 10 CANH*e 3.39,1.671 3.39,0.922 3.39,0.922 4.273,0.922 false 2.342,0.59 2.899,0.752 0.557,0.162 10 CANH*d 0.052,0.026 0.228,0.188 0.176,0.162 10 *a 3.264,1.666 3.264,0.663 3.264,0.663 2.896,0.663 false 3.027,1.91 3.027,2.136 3.027,2.136 2.659,2.136 false 2.242,2.304 2.779,2.459 0.537,0.156 10 CANL*c 3.144,1.913 3.144,2.374 3.144,2.374 2.776,2.374 false 2.366,2.525 2.903,2.680 0.537,0.156 10 CANL*d 3.268,1.912 3.268,2.594 3.268,2.594 2.9,2.594 false 3.513,1.912 3.513,2.141 3.513,2.141 4.395,2.141 false 4.291,2.324 4.848,2.486 0.557,0.162 10 CANL*e 3.386,1.913 3.386,2.395 3.386,2.395 4.268,2.395 false

Text in Illustration
*a Front view of wire harness connector
(to CAN Junction Connector LH (Instrument Panel Wire Side))
*b to Main Body ECU (Multiplex Network Body ECU)
(for V Bus)
*c to Power Steering ECU Assembly
(for V Bus)
*d to DLC3
*e to CAN Junction Connector RH
(for V Bus)
*f to Power Management Control ECU
(for V Bus)


ii.

Check the connection diagram of the components which are connected to the CAN junction connector LH.

Terminal No. (Symbol) Wiring Color Connected to
G71-1 (CANH) R Main body ECU (Multiplex network body ECU)
(for V bus)
G71-12 (CANL) W
G71-2 (CANH) LG Power steering ECU assembly
(for V bus)
G71-13 (CANL) W
G71-3 (CANH) GR DLC3
G71-14 (CANL) W
G71-4 (CANH) SB CAN junction connector RH
(for V bus)
G71-15 (CANL) W
G71-5 (CANH) BE Power management control ECU
(for V bus)
G71-16 (CANL) W



b.

Check the CAN junction connector LH (engine room main wire side) (for V bus).

i.

Connection diagram

U159503E01
3.495,0.366 3.778,0.519 0.283,0.153 10 A51 5.026,1.117 5.584,1.279 0.557,0.162 10 CANH*c 5.026,2.063 5.584,2.225 0.557,0.162 10 CANL*c 4.118,1.663 4.118,1.188 4.118,1.188 5.001,1.188 false 4.906,0.845 5.464,1.007 0.557,0.162 10 CANH*b 3.998,1.664 3.998,0.916 3.998,0.916 4.881,0.916 false 0.052,0.019 0.228,0.181 0.176,0.162 10 *a 4.121,1.905 4.121,2.135 4.121,2.135 5.003,2.135 false 4.899,2.318 5.456,2.480 0.557,0.162 10 CANL*b 3.994,1.907 3.994,2.389 3.994,2.389 4.876,2.389 false

Text in Illustration
*a Front view of wire harness connector
(to CAN Junction Connector LH (Engine Room Main Wire Side))
*b to ECM
(for V Bus)
*c to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
(for V Bus)
- -


ii.

Check the connection diagram of the components which are connected to the CAN junction connector LH.

Terminal No. (Symbol) Wiring Color Connected to
A51-9 (CANH) L ECM
(for V bus)
A51-20 (CANL) W
A51-10 (CANH) B Brake booster with master cylinder assembly (Skid control ECU)
(for V bus)
A51-21 (CANL) W




CAN JUNCTION CONNECTOR LH (for RHD)


HINT:

The following tables contain information about the items and buses connected via junction connectors. The junction connector may be used for multiple separate buses. In this case, the name of the bus will be shown below the name of the item that the terminals are connected to. The bus name will be shown in brackets (example: (for Sub bus 15)).


a.

Check the CAN junction connector LH (instrument panel wire side) (for V bus).

i.

Connection diagram

U183585E01
2.105,1.175 2.663,1.337 0.557,0.162 10 CANH*b 2.125,2.066 2.662,2.222 0.537,0.156 10 CANL*b 3.495,0.372 3.778,0.526 0.283,0.153 10 G71 3.027,1.667 3.027,1.248 3.027,1.248 2.659,1.248 false 4.418,1.124 4.975,1.285 0.557,0.162 10 CANH*e 4.418,2.07 4.975,2.232 0.557,0.162 10 CANL*e 3.51,1.669 3.51,1.194 3.51,1.194 4.393,1.194 false 4.298,0.852 4.856,1.014 0.557,0.162 10 CANH*d 3.39,1.671 3.39,0.922 3.39,0.922 4.273,0.922 false 2.342,0.785 2.899,0.947 0.557,0.162 10 CANH*c 0.052,0.026 0.228,0.188 0.176,0.162 10 *a 3.264,1.666 3.264,0.858 3.264,0.858 2.896,0.858 false 3.027,1.91 3.027,2.136 3.027,2.136 2.659,2.136 false 2.366,2.441 2.903,2.597 0.537,0.156 10 CANL*c 3.268,1.912 3.268,2.511 3.268,2.511 2.9,2.511 false 3.513,1.912 3.513,2.141 3.513,2.141 4.395,2.141 false 4.291,2.324 4.848,2.486 0.557,0.162 10 CANL*d 3.386,1.913 3.386,2.395 3.386,2.395 4.268,2.395 false

Text in Illustration
*a Front view of wire harness connector
(to CAN Junction Connector LH (Instrument Panel Wire Side))
*b to Main Body ECU (Multiplex Network Body ECU)
(for V Bus)
*c to Smart Key ECU Assembly (Certification ECU)
(for V Bus)
*d to CAN Junction Connector RH
(for V Bus)
*e to Power Management Control ECU
(for V Bus)
- -


ii.

Check the connection diagram of the components which are connected to the CAN junction connector LH.

Terminal No. (Symbol) Wiring Color Connected to
G71-1 (CANH) R Main body ECU (Multiplex network body ECU)
(for V bus)
G71-12 (CANL) W
G71-3 (CANH) L Smart key ECU assembly (Certification ECU)
(for V bus)
G71-14 (CANL) W
G71-4 (CANH) SB CAN junction connector RH
(for V bus)
G71-15 (CANL) W
G71-5 (CANH) BE Power management control ECU
(for V bus)
G71-16 (CANL) W



b.

Check the CAN junction connector LH (engine room main wire side) (for V bus).

i.

Connection diagram

U159503E01
3.495,0.366 3.778,0.519 0.283,0.153 10 A51 5.026,1.117 5.584,1.279 0.557,0.162 10 CANH*c 5.026,2.063 5.584,2.225 0.557,0.162 10 CANL*c 4.118,1.663 4.118,1.188 4.118,1.188 5.001,1.188 false 4.906,0.845 5.464,1.007 0.557,0.162 10 CANH*b 3.998,1.664 3.998,0.916 3.998,0.916 4.881,0.916 false 0.052,0.019 0.228,0.181 0.176,0.162 10 *a 4.121,1.905 4.121,2.135 4.121,2.135 5.003,2.135 false 4.899,2.318 5.456,2.480 0.557,0.162 10 CANL*b 3.994,1.907 3.994,2.389 3.994,2.389 4.876,2.389 false

Text in Illustration
*a Front view of wire harness connector
(to CAN Junction Connector LH (Engine Room Main Wire Side))
*b to ECM
(for V Bus)
*c to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
(for V Bus)
- -


ii.

Check the connection diagram of the components which are connected to the CAN junction connector LH.

Terminal No. (Symbol) Wiring Color Connected to
A51-9 (CANH) L ECM
(for V bus)
A51-20 (CANL) W
A51-10 (CANH) B Brake booster with master cylinder assembly (Skid control ECU)
(for V bus)
A51-21 (CANL) W




CAN JUNCTION CONNECTOR RH (for LHD)


a.

Check the CAN junction connector RH (for V bus).

i.

Connection diagram

U183586E01
2.105,1.175 2.663,1.337 0.557,0.162 10 CANH*b 2.125,2.066 2.662,2.222 0.537,0.156 10 CANL*b 3.495,0.372 3.778,0.526 0.283,0.153 10 G72 3.027,1.667 3.027,1.248 3.027,1.248 2.659,1.248 false 2.346,0.866 2.903,1.028 0.557,0.162 10 CANH*c 4.784,1.124 5.342,1.285 0.557,0.162 10 CANH*f 4.784,2.257 5.342,2.419 0.557,0.162 10 CANL*f 3.268,1.669 3.268,0.939 3.268,0.939 2.9,0.939 false 3.876,1.669 3.876,1.194 3.876,1.194 4.759,1.194 false 5.026,1.388 5.583,1.550 0.557,0.162 10 CANH*g 4.118,1.666 4.118,1.459 4.118,1.459 5.001,1.459 false 4.665,0.852 5.222,1.014 0.557,0.162 10 CANH*e 3.756,1.671 3.756,0.922 3.756,0.922 4.639,0.922 false 2.466,0.59 3.023,0.752 0.557,0.162 10 CANH*d 0.052,0.026 0.228,0.188 0.176,0.162 10 *a 3.388,1.666 3.388,0.663 3.388,0.663 3.02,0.663 false 3.027,1.91 3.027,2.136 3.027,2.136 2.659,2.136 false 2.366,2.304 2.903,2.459 0.537,0.156 10 CANL*c 3.268,1.913 3.268,2.374 3.268,2.374 2.9,2.374 false 2.49,2.525 3.027,2.680 0.537,0.156 10 CANL*d 3.392,1.912 3.392,2.594 3.392,2.594 3.024,2.594 false 3.88,1.912 3.88,2.328 3.88,2.328 4.761,2.328 false 5.021,1.981 5.561,2.143 0.540,0.162 10 CANL*g 4.117,1.912 4.117,2.052 4.117,2.052 4.998,2.052 false 4.657,2.511 5.215,2.673 0.557,0.162 10 CANL*e 3.753,1.913 3.753,2.582 3.753,2.582 4.634,2.582 false

Text in Illustration
*a Front view of wire harness connector
(to CAN Junction Connector RH)
*b to Spiral Cable with Sensor Sub-assembly (Steering Sensor)
(for V Bus)
*c to Smart Key ECU Assembly (Certification ECU)
(for V Bus)
*d to Airbag Sensor Assembly
(for V Bus)
*e to Combination Meter Assembly
(for V Bus)
*f to Air Conditioning Amplifier Assembly
(for V Bus)
*g to CAN Junction Connector LH
(for V Bus)
- -


ii.

Check the connection diagram of the components which are connected to the CAN junction connector RH.

Terminal No. (Symbol) Wiring Color Connected to
G72-1 (CANH) P Spiral cable with sensor sub-assembly (Steering sensor)
(for V bus)
G72-12 (CANL) W
G72-3 (CANH) L Smart key ECU assembly (Certification ECU)
(for V bus)
G72-14 (CANL) W
G72-4 (CANH) B Airbag sensor assembly
(for V bus)
G72-15 (CANL) W
G72-7 (CANH) G Combination meter assembly
(for V bus)
G72-18 (CANL) W
G72-8 (CANH) V Air conditioning amplifier assembly
(for V bus)
G72-19 (CANL) W
G72-10 (CANH) SB CAN junction connector LH
(for V bus)
G72-21 (CANL) W




CAN JUNCTION CONNECTOR RH (for RHD)


a.

Check the CAN junction connector RH (for V bus).

i.

Connection diagram

U183587E01
2.105,1.168 2.663,1.330 0.557,0.162 10 CANH*b 2.125,2.06 2.662,2.215 0.537,0.156 10 CANL*b 3.495,0.366 3.778,0.519 0.283,0.153 10 G72 3.027,1.661 3.027,1.241 3.027,1.241 2.659,1.241 false 2.469,0.86 3.026,1.022 0.557,0.162 10 CANH*c 4.784,0.81 5.342,0.972 0.557,0.162 10 CANH*f 4.784,2.383 5.342,2.545 0.557,0.162 10 CANL*f 3.391,1.663 3.391,0.933 3.391,0.933 3.023,0.933 false 3.876,1.663 3.876,0.88 3.876,0.88 4.759,0.88 false 5.026,1.036 5.583,1.198 0.557,0.162 10 CANH*g 4.118,1.66 4.118,1.106 4.118,1.106 5.001,1.106 false 5.148,1.279 5.705,1.441 0.557,0.162 10 CANH*h 4.239,1.658 4.239,1.35 4.239,1.35 5.123,1.35 false 4.665,0.576 5.222,0.738 0.557,0.162 10 CANH*e 3.756,1.664 3.756,0.647 3.756,0.647 4.639,0.647 false 2.709,0.584 3.266,0.746 0.557,0.162 10 CANH*d 0.052,0.019 0.228,0.181 0.176,0.162 10 *a 3.631,1.66 3.631,0.656 3.631,0.656 3.263,0.656 false 3.027,1.903 3.027,2.13 3.027,2.13 2.659,2.13 false 2.488,2.297 3.025,2.453 0.537,0.156 10 CANL*c 3.39,1.906 3.39,2.367 3.39,2.367 3.023,2.367 false 2.733,2.518 3.270,2.674 0.537,0.156 10 CANL*d 3.635,1.905 3.635,2.588 3.635,2.588 3.268,2.588 false 3.88,1.905 3.88,2.454 3.88,2.454 4.761,2.454 false 5.021,2.178 5.561,2.340 0.540,0.162 10 CANL*g 4.117,1.906 4.117,2.249 4.117,2.249 4.998,2.249 false 5.145,1.966 5.685,2.128 0.540,0.162 10 CANL*h 4.24,1.906 4.24,2.037 4.24,2.037 5.121,2.037 false 4.657,2.593 5.215,2.755 0.557,0.162 10 CANL*e 3.753,1.907 3.753,2.664 3.753,2.664 4.634,2.664 false

Text in Illustration
*a Front view of wire harness connector
(to CAN Junction Connector RH)
*b to Spiral Cable with Sensor Sub-assembly (Steering Sensor)
(for V Bus)
*c to Airbag Sensor Assembly
(for V Bus)
*d to Power Steering ECU Assembly
(for V Bus)
*e to Combination Meter Assembly
(for V Bus)
*f to Air Conditioning Amplifier Assembly
(for V Bus)
*g to CAN Junction Connector LH
(for V Bus)
*h to DLC3


ii.

Check the connection diagram of the components which are connected to the CAN junction connector RH.

Terminal No. (Symbol) Wiring Color Connected to
G72-1 (CANH) P Spiral cable with sensor sub-assembly (Steering sensor)
(for V bus)
G72-12 (CANL) W
G72-4 (CANH) B Airbag sensor assembly
(for V bus)
G72-15 (CANL) W
G72-6 (CANH) LG Power steering ECU assembly
(for V bus)
G72-17 (CANH) W
G72-7 (CANH) G Combination meter assembly
(for V bus)
G72-18 (CANL) W
G72-8 (CANH) V Air conditioning amplifier assembly
(for V bus)
G72-19 (CANL) W
G72-10 (CANH) SB CAN junction connector LH
(for V bus)
G72-21 (CANL) W
G72-11 (CANH) GR DLC3
G72-22 (CANH) W




CAN JUNCTION CONNECTOR LH


a.

Check the CAN junction connector LH (engine room main wire side) (for Sub bus 15).

i.

Connection diagram

U159504E01
3.495,0.366 3.778,0.519 0.283,0.153 10 A51 2.093,1.056 2.650,1.218 0.557,0.162 10 CANH*c 2.097,2.366 2.655,2.528 0.557,0.162 10 CANL*c 3.033,1.663 3.033,1.436 3.033,1.436 2.418,1.436 false 3.269,1.66 3.269,1.134 3.269,1.134 2.654,1.134 false 3.269,1.908 3.269,2.434 3.269,2.434 2.655,2.434 false 1.857,1.356 2.414,1.518 0.557,0.162 10 CANH*b 0.052,0.019 0.228,0.181 0.176,0.162 10 *a 3.033,1.905 3.033,2.135 3.033,2.135 2.417,2.135 false 1.867,2.064 2.424,2.226 0.557,0.162 10 CANL*b

Text in Illustration
*a Front view of wire harness connector
(to CAN Junction Connector LH (Engine Room Main Wire Side))
*b to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
(for Sub Bus 15)
*c to ECM
(for Sub Bus 15)
- -


ii.

Check the connection diagram of the components which are connected to the CAN junction connector LH.

Terminal No. (Symbol) Wiring Color Connected to
A51-1 (CANH) L Brake booster with master cylinder assembly (Skid control ECU)
(for Sub bus 15)
A51-12 (CANL) W
A51-3 (CANH) B ECM
(for Sub bus 15)
A51-14 (CANL) W



b.

Check the CAN junction connector LH (instrument panel wire side) (for Sub bus 15).

i.

Connection diagram

U159505E01
3.495,0.366 3.778,0.519 0.283,0.153 10 G71 5.029,1.225 5.586,1.387 0.557,0.162 10 CANH*b 4.12,1.659 4.12,1.296 4.12,1.296 5.003,1.296 false 0.052,0.019 0.228,0.181 0.176,0.162 10 *a 5.034,2.202 5.592,2.364 0.557,0.162 10 CANL*b 4.13,1.911 4.13,2.273 4.13,2.273 5.011,2.273 false

Text in Illustration
*a Front view of wire harness connector
(to CAN Junction Connector LH (Instrument Panel Wire Side))
*b to Power Management Control ECU
(for Sub Bus 15)


ii.

Check the connection diagram of the components which are connected to the CAN junction connector LH.

Terminal No. (Symbol) Wiring Color Connected to
G71-10 (CANH) R Power management control ECU
(for Sub bus 15)
G71-21 (CANL) W




DLC3


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U183517E01
0.087,0.032 0.263,0.187 0.175,0.155 10 *1 1.605,0.763 1.989,1.055 0.385,0.293 10 G4 2.194,1.084 2.604,1.231 0.411,0.147 10 CANH 0.994,1.124 1.225,1.278 0.230,0.154 10 CG 1.25,2.947 1.637,3.128 0.387,0.181 10 CANL 2.608,2.828 2.896,2.996 0.288,0.167 10 BAT 2.078,1.828 2.441,1.27 false 2.085,2.535 1.492,2.92 false 2.511,2.526 2.759,2.811 false 1.646,1.833 1.133,1.32 false

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*1 DLC3

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G4-6 (CANH) - G4-14 (CANL) GR - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
G4-6 (CANH) - G4-4 (CG) GR - P HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G4-14 (CANL) - G4-4 (CG) W - P LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G4-6 (CANH) - G4-16 (BAT) GR - SB HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G4-14 (CANL) - G4-16 (BAT) W - SB LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




POWER MANAGEMENT CONTROL ECU


U183501E02
5.146,1.167 4.313,0.26 false 5.271,1.156 6.031,0.25 false 5.156,1.021 4.854,0.271 false 5.26,1 5.458,0.25 false 2.792,1.49 3.052,1.625 0.26,0.135 10 false A39 4.281,1.479 4.563,1.615 0.281,0.135 10 false G57 1.427,1.49 1.688,1.625 0.26,0.135 10 false A38 0.083,0.052 0.24,0.188 0.156,0.135 10 false *a 5.49,1.479 5.771,1.615 0.281,0.135 10 false G58 4.146,0.063 4.542,0.219 0.396,0.156 10 false CA3P 5.823,0.063 6.219,0.219 0.396,0.156 10 false CA3N 4.688,0.063 5.083,0.219 0.396,0.156 10 false CA1H 5.271,0.063 5.667,0.219 0.396,0.156 10 false CA1L

Text in Illustration
*a Component without harness connected
(Power Management Control ECU)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U183184E02
2.469,2.51 1.646,2.219 false 2.427,2.521 1.677,2.469 false 2.427,2.365 2.104,2.104 false 1.708,2.771 2.427,2.573 false 1.75,3.063 2.469,2.583 false 1.823,1.396 1.573,0.896 false 2.5,2.969 2.781,3.115 0.281,0.146 10 false G58 1.229,2.083 1.594,2.26 0.365,0.177 10 false CA1L 1.219,2.365 1.604,2.542 0.385,0.177 10 false CA1H 1.292,2.708 1.677,2.885 0.385,0.177 10 false CA3P 1.344,3.01 1.729,3.188 0.385,0.177 10 false CA3N 0.156,0.063 0.354,0.229 0.198,0.167 10 false *a 1.729,1.948 2.104,2.125 0.375,0.177 10 false AM21 1.354,0.729 1.542,0.875 0.188,0.146 10 false E1 1.917,0.74 2.198,0.885 0.281,0.146 10 false G57

Disconnect the power management control ECU connectors.

Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G58-25 (CA1H) - G58-24 (CA1L) BE - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
G58-25 (CA1H) - G57-6 (E1) BE - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G58-24 (CA1L) - G57-6 (E1) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G58-25 (CA1H) - G58-7 (AM21) BE - B HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G58-24 (CA1L) - G58-7 (AM21) W - B LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Standard Resistance:
Sub Bus 15 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G58-31 (CA3P) - G58-30 (CA3N) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
G58-31 (CA3P) - G57-6 (E1) R - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G58-30 (CA3N) - G57-6 (E1) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G58-31 (CA3P) - G58-7 (AM21) R - B HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G58-30 (CA3N) - G58-7 (AM21) W - B LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




ECM


U183553E02
5.125,1.417 4.51,0.76 4.51,0.76 4.313,0.76 false 5.25,1.417 5.76,0.76 5.76,0.76 6.031,0.76 false 5.125,1.292 4.844,0.427 4.844,0.427 4.552,0.427 false 5.25,1.302 5.333,0.438 5.333,0.438 5.573,0.438 false 5.875,2.24 6.198,2.406 0.323,0.167 10 false A40 1.906,2.24 2.104,2.396 0.198,0.156 10 false C9 2.219,2.333 2.417,2.49 0.198,0.156 10 false *B 3.406,2.333 3.604,2.49 0.198,0.156 10 false *A 3.063,2.24 3.344,2.396 0.281,0.156 10 false C10 4.146,0.354 4.573,0.521 0.427,0.167 10 false CANH 5.604,0.365 6.031,0.531 0.427,0.167 10 false CANP 6.063,0.688 6.49,0.854 0.427,0.167 10 false CANN 3.917,0.698 4.344,0.865 0.427,0.167 10 false CANL 0.115,0.104 0.365,0.313 0.25,0.208 10 false *a

Text in Illustration
*A for LHD *B for RHD
*a Component without harness connected
(ECM)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the ECM connectors.

U183639E02
2.5,1.271 2.5,0.844 2.5,0.844 2.75,0.844 false 2.427,1.281 2.427,0.615 2.427,0.615 2.677,0.615 false 2.5,1.354 2.5,1.927 2.5,1.927 2.75,1.927 false 2.427,1.354 2.427,2.208 2.427,2.208 2.667,2.208 false 4.813,1.281 4.708,0.74 4.708,0.74 4.5,0.74 false 1.521,1.271 1.417,0.729 1.417,0.729 1.208,0.729 false 1.792,2.083 2.052,2.26 0.26,0.177 10 false A40 4.427,1.948 4.625,2.125 0.198,0.177 10 false C9 5.375,1.938 5.646,2.115 0.271,0.177 10 false C10 4.74,2.021 4.906,2.167 0.167,0.146 10 false *B 0.083,0.052 0.25,0.198 0.167,0.146 10 false *a 2.781,0.771 3.198,0.917 0.417,0.146 10 false CANH 4.302,0.667 4.51,0.823 0.208,0.156 10 false E1 2.719,0.531 3.135,0.677 0.417,0.146 10 false CANP 2.781,1.854 3.198,2 0.417,0.146 10 false CANL 2.708,2.135 3.125,2.281 0.417,0.146 10 false CANN 5.74,2.01 5.906,2.156 0.167,0.146 10 false *A 0.833,0.667 1.208,0.813 0.375,0.146 10 false BATT

Text in Illustration
*A for LHD *B for RHD
*a Front view of wire harness connector
(to ECM)
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A40-13 (CANH) - A40-26 (CANL) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
A40-13 (CANH) - C10-16 (E1)*1
A40-13 (CANH) - C9-16 (E1)*2
L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A40-26 (CANL) - C10-16 (E1)*1
A40-26 (CANL) - C9-16 (E1)*2
W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A40-13 (CANH) - A40-1 (BATT) L - Y HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A40-26 (CANL) - A40-1 (BATT) W - Y LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


*1: for LHD

*2: for RHD

Standard Resistance:
Sub Bus 15 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A40-12 (CANP) - A40-25 (CANN) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
A40-12 (CANP) - C10-16 (E1)*1
A40-12 (CANP) - C9-16 (E1)*2
B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A40-25 (CANN) - C10-16 (E1)*1
A40-25 (CANN) - C9-16 (E1)*2
W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A40-12 (CANP) - A40-1 (BATT) B - Y HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A40-25 (CANN) - A40-1 (BATT) W - Y LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




*1: for LHD

*2: for RHD

BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU)


U159318E01
0.25,0.235 0.489,0.412 0.239,0.177 10 *a 3.462,0.696 3.735,0.852 0.272,0.156 10 A41 2.461,2.098 2.859,2.254 0.398,0.155 10 CA1L 4.09,2.098 4.488,2.254 0.398,0.155 10 CA2L 3.268,1.873 3.06,2.164 3.06,2.164 2.861,2.164 false 3.681,1.873 3.854,2.164 3.854,2.164 4.059,2.164 false 2.538,2.358 2.936,2.513 0.398,0.155 10 CA1H 4.032,2.358 4.430,2.513 0.398,0.155 10 CA2H 3.363,1.875 3.137,2.423 3.137,2.423 2.938,2.423 false 3.58,1.875 3.765,2.423 3.765,2.423 4.008,2.423 false

Text in Illustration
*a Component without harness connected
(Brake Booster with Master Cylinder Assembly (Skid Control ECU))
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U183565E01
0.196,0.187 0.380,0.345 0.184,0.158 10 *a 1.566,0.857 1.854,1.015 0.288,0.158 10 A41 1.662,2.145 0.57,2.778 false 0.312,2.791 0.725,2.948 0.413,0.158 10 CA2L 0.832,2.791 1.245,2.948 0.413,0.158 10 CA2H 1.358,2.791 1.771,2.948 0.413,0.158 10 CA1H 1.9,2.791 2.312,2.948 0.413,0.158 10 CA1L 2.45,2.791 2.807,2.948 0.356,0.158 10 GND 2.686,0.739 2.856,0.897 0.171,0.158 10 BI 1.759,2.145 1.066,2.774 false 1.976,2.137 1.598,2.768 false 2.081,2.142 2.094,2.768 false 2.475,1.652 2.764,0.928 false 2.654,2.033 2.654,2.763 false

Disconnect the brake booster with master cylinder assembly (skid control ECU) connector.

Text in Illustration
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly (Skid Control ECU))


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A41-37 (CA1H) - A41-38 (CA1L) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A41-37 (CA1H) - A41-28 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A41-38 (CA1L) - A41-28 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A41-37 (CA1H) - A41-14 (BI) B - W HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A41-38 (CA1L) - A41-14 (BI) W - W LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Standard Resistance:
Sub Bus 15 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A41-35 (CA2H) - A41-34 (CA2L) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A41-35 (CA2H) - A41-28 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A41-34 (CA2L) - A41-28 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A41-35 (CA2H) - A41-14 (BI) L - W HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A41-34 (CA2L) - A41-14 (BI) W - W LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




AIRBAG SENSOR ASSEMBLY


U159349E01
2.633,0.189 2.912,0.370 0.280,0.181 10 G18 3.924,0.189 4.211,0.370 0.287,0.181 10 M36 4.824,0.189 5.111,0.370 0.287,0.181 10 M37 0.059,0.064 0.222,0.217 0.163,0.153 10 *a 1.317,0.149 1.738,0.302 0.421,0.153 10 CANH 3.015,0.136 3.435,0.289 0.421,0.153 10 CANL 3.172,0.946 2.05,0.217 2.05,0.217 1.735,0.217 false 3.345,1.222 3.703,0.201 3.703,0.201 3.428,0.201 false

Text in Illustration
*a Component without harness connected
(Airbag Sensor Assembly)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the airbag sensor assembly connector.

U183511E01
0.185,0.161 0.363,0.347 0.178,0.186 10 *a 1.008,2.363 1.402,2.511 0.394,0.149 10 CANL 1.02,0.988 1.445,1.140 0.425,0.152 10 CANH 1.599,2.265 1.791,2.421 0.191,0.156 10 E1 5.849,2.333 6.197,2.495 0.349,0.163 10 BAT 1.61,0.924 1.900,1.088 0.290,0.165 10 G18 1.23,1.133 1.516,1.615 false 1.42,1.885 1.204,2.35 false 5.725,1.912 5.941,2.311 false 3.394,0.161 3.893,0.327 0.499,0.166 10 *1 5.013,0.862 5.230,1.013 0.217,0.151 10 G4 1.696,1.892 1.696,2.255 false

Text in Illustration
*1 DLC3 - -
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G18-13 (CANH) - G18-22 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
G18-13 (CANH) - G18-25 (E1) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G18-22 (CANL) - G18-25 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G18-13 (CANH) - G4-16 (BAT) B - SB HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G18-22 (CANL) - G4-16 (BAT) W - SB LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


U183415E02
4.052,1.031 4.052,0.625 4.052,0.625 4.167,0.625 false 1.677,1.417 1.927,1.417 false 0.729,2.677 1.042,2.677 false 1.625,0.854 1.625,0.427 1.625,0.427 1.802,0.427 false 4.219,0.552 4.448,0.688 0.229,0.135 10 false MB 3.448,7.896 3.677,8.031 0.229,0.135 10 false MB 0.396,2.531 0.76,2.688 0.365,0.156 10 false 3E*B 0.396,2.688 0.813,2.833 0.417,0.146 10 false 3F*C 5.031,5.208 5.24,5.344 0.208,0.135 10 false 3C 0.906,1.354 1.104,1.49 0.198,0.135 10 false 3D 0.146,0.094 0.344,0.229 0.198,0.135 10 false *A 5.042,3.833 5.24,3.99 0.198,0.156 10 false *B 5.615,3.833 5.813,4.01 0.198,0.177 10 false *C 1.823,5.198 2.021,5.333 0.198,0.135 10 false 3D 5.875,1.313 6.073,1.448 0.198,0.135 10 false 3B 1.823,6.563 2.021,6.698 0.198,0.135 10 false 3B 5.875,2 6.063,2.135 0.188,0.135 10 false 3A 5.083,6.563 5.271,6.698 0.188,0.135 10 false 3A 0.906,1.99 1.115,2.125 0.208,0.135 10 false 3C 1.938,1.323 2.302,1.542 0.365,0.219 10 false G59 1.833,0.344 2.125,0.479 0.292,0.135 10 false *1 5.333,3.865 5.563,4 0.229,0.135 10 false 3F 1.719,3.865 2.01,4 0.292,0.135 10 false G59 4.76,3.865 5.021,4 0.26,0.135 10 false 3E

Text in Illustration
*A Component without harness connected
(Main body ECU (multiplex network body ECU) with 1 connector)
*B for LHD
*C for RHD - -
*1 Main body ECU (multiplex network body ECU) - -

U183433E02
1.635,0.958 1.635,0.615 1.635,0.615 1.771,0.615 false 4.094,1.146 4.094,0.635 4.094,0.635 4.229,0.635 false 1.677,1.531 1.948,1.531 false 1.677,1.958 1.948,1.958 false 0.771,2.719 1.042,2.719 false 2.219,3.792 2.5,3.948 0.281,0.156 10 false G60 4.698,3.802 4.979,3.958 0.281,0.156 10 false G59 1.156,5.063 1.438,5.219 0.281,0.156 10 false 3D 3.927,5.042 4.208,5.198 0.281,0.156 10 false 3C 1.813,6.313 2.094,6.469 0.281,0.156 10 false 3B 3.469,7.563 3.75,7.719 0.281,0.156 10 false MB 4.927,6.302 5.208,6.458 0.281,0.156 10 false 3A 5.896,5.052 6.177,5.208 0.281,0.156 10 false 3F 0.146,0.083 0.427,0.24 0.281,0.156 10 false *A 1.813,0.531 2.094,0.688 0.281,0.156 10 false *1 1.969,1.469 2.26,1.625 0.292,0.156 10 false G59 1.969,1.885 2.26,2.042 0.292,0.156 10 false G60 4.271,0.563 4.563,0.76 0.292,0.198 10 false MB 5.875,1.417 6.156,1.573 0.281,0.156 10 false 3B 5.875,2.094 6.156,2.25 0.281,0.156 10 false 3A 0.906,1.417 1.188,1.573 0.281,0.156 10 false 3D 0.906,2.094 1.188,2.25 0.281,0.156 10 false 3C 0.552,2.656 0.771,2.813 0.219,0.156 10 false 3F

Text in Illustration
*A Component without harness connected
(Main body ECU (multiplex network body ECU) with 2 connectors)
- -
*1 Main body ECU (multiplex network body ECU) - -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the main body ECU (multiplex network body ECU) connectors.

U159496E02
4.458,0.51 4.25,0.51 4.25,0.51 3.771,1.448 false 4.563,0.792 4.396,0.792 4.396,0.792 3.865,1.458 false 4.802,4.115 4.646,4.115 4.646,4.115 4.302,3.958 false 3.99,2.885 3.75,2.885 3.75,2.885 3.604,3.406 false 1.938,0.333 2.208,0.635 0.271,0.302 10 false *a 1.927,2.76 2.396,3.052 0.469,0.292 10 false *1 4.844,4.021 5.135,4.198 0.292,0.177 10 false BAT 3.51,0.427 3.792,0.594 0.281,0.167 10 false G59 3.552,2.458 3.76,2.625 0.208,0.167 10 false G4 4.5,0.438 4.896,0.583 0.396,0.146 10 false CANL 4.594,0.719 5,0.865 0.406,0.146 10 false CANH 4.031,2.802 4.438,2.979 0.406,0.177 10 false CG

Text in Illustration
*1 DLC3 - -
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G59-14 (CANH) - G59-13 (CANL) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
G59-14 (CANH) - G4-4 (CG) R - P HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G59-13 (CANL) - G4-4 (CG) W - P LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G59-14 (CANH) - G4-16 (BAT) R - SB HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G59-13 (CANL) - G4-16 (BAT) W - SB LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY (STEERING SENSOR)


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U159561E01
1.591,1.067 1.873,1.215 0.282,0.147 10 G30 0.41,1.322 0.724,1.470 0.314,0.147 10 ESS 0.844,2.677 1.242,2.824 0.398,0.147 10 CANL 2.192,2.672 2.633,2.819 0.440,0.147 10 CANH 2.671,1.322 2.967,1.470 0.296,0.147 10 BAT 0.06,0.038 0.217,0.185 0.158,0.147 10 *a 1.376,2.095 1.055,1.402 1.055,1.402 0.791,1.402 false 2.364,2.105 2.364,1.396 2.364,1.396 2.654,1.396 false 1.639,2.317 1.505,2.752 1.505,2.752 1.32,2.752 false 1.88,2.317 1.962,2.752 1.962,2.752 2.178,2.752 false

Disconnect the spiral cable with sensor sub-assembly (steering sensor) connector.

Text in Illustration
*a Front view of wire harness connector
(to Spiral Cable with Sensor Sub-assembly (Steering Sensor))


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G30-4 (CANH) - G30-3 (CANL) P - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
G30-4 (CANH) - G30-2 (ESS) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G30-3 (CANL) - G30-2 (ESS) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G30-4 (CANH) - G30-6 (BAT) P - B HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G30-3 (CANL) - G30-6 (BAT) W - B LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




POWER STEERING ECU ASSEMBLY


U183538E02
1.531,1.479 1.052,1.479 false 1.719,1.448 1.969,0.729 1.969,0.729 2.25,0.729 false 1.677,2.031 1.875,2.177 0.198,0.146 10 false G6 2.375,2.031 2.542,2.177 0.167,0.146 10 false z7 3.427,2.031 3.594,2.177 0.167,0.146 10 false z8 4.885,2.031 5.156,2.177 0.271,0.146 10 false A33 0.135,0.083 0.302,0.25 0.167,0.167 10 false *a 0.646,1.396 1.063,1.552 0.417,0.156 10 false CANL 2.271,0.646 2.688,0.802 0.417,0.156 10 false CANH

Text in Illustration
*a Component without harness connected
(Power Steering ECU Assembly)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the power steering ECU assembly connectors.

U159559E03
1.865,1.906 2.323,1.906 false 1.729,1.875 2.083,1.531 2.083,1.531 2.292,1.531 false 4.802,1.531 4.354,1.531 false 6.135,1.531 5.688,1.531 false 1.531,2.313 2.01,2.625 0.479,0.313 10 false G6 0.198,0.115 0.365,0.271 0.167,0.156 10 false *a 2.385,1.833 3.104,2.115 0.719,0.281 10 false CANL 2.354,1.458 3.146,1.729 0.792,0.271 10 false CANH 4.073,1.458 4.521,1.698 0.448,0.24 10 false PIG 6.198,1.448 6.802,1.677 0.604,0.229 10 false PGND 5.188,2.302 5.615,2.542 0.427,0.24 10 false A33

Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU Assembly)
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G6-7 (CANH) - G6-8 (CANL) LG - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
G6-7 (CANH) - A33-2 (PGND) LG - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G6-8 (CANL) - A33-2 (PGND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G6-7 (CANH) - A33-1 (PIG) LG - W HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G6-8 (CANL) - A33-1 (PIG) W - W LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




SMART KEY ECU ASSEMBLY (CERTIFICATION ECU)


U183547E02
4.115,1.229 3.99,0.698 3.99,0.698 3.792,0.698 false 4.229,1.229 4.323,0.698 4.323,0.698 4.531,0.698 false 1.74,1.74 2.031,1.896 0.292,0.156 10 false G53 0.104,0.042 0.344,0.24 0.24,0.198 10 false *a 3.458,1.75 3.75,1.906 0.292,0.156 10 false G54 4.927,1.74 5.208,1.896 0.281,0.156 10 false G55 3.396,0.615 3.792,0.771 0.396,0.156 10 false CANL 4.563,0.604 5,0.76 0.438,0.156 10 false CANH

Text in Illustration
*a Component without harness connected
(Smart Key ECU Assembly (Certification ECU))
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the smart key ECU assembly (certification ECU) connector.

U183576E02
1.01,0.99 1.073,0.99 1.073,0.99 1.073,1.635 false 4.594,1 4.813,1 4.813,1 4.813,1.646 false 1.26,0.99 1.198,0.99 1.198,0.99 1.198,1.625 false 2.458,1 2.396,1 2.396,1 2.396,1.635 false 0.063,0.031 0.313,0.24 0.25,0.208 10 false *a 0.583,0.896 1.031,1.052 0.448,0.156 10 false CANH 1.594,2.219 1.875,2.375 0.281,0.156 10 false G54 1.302,0.906 1.75,1.063 0.448,0.156 10 false CANL 4.469,0.927 4.594,1.083 0.125,0.156 10 false E 2.5,0.906 2.948,1.063 0.448,0.156 10 false +B 5.406,2.219 5.698,2.375 0.292,0.156 10 false G55

Text in Illustration
*a Front view of wire harness connector
(to Smart Key ECU Assembly (Certification ECU))
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G54-1 (CANH) - G54-2 (CANL) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
G54-1 (CANH) - G55-1 (E) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G54-2 (CANL) - G55-1 (E) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G54-1 (CANH) - G54-5 (+B) L - BE HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G54-2 (CANL) - G54-5 (+B) W - BE LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




COMBINATION METER ASSEMBLY


U159502E01
2.198,0.255 2.403,0.408 0.205,0.153 10 G1 5.08,0.255 5.285,0.408 0.205,0.153 10 G3 0.077,0.058 0.282,0.212 0.205,0.153 10 *a 1.443,1.378 1.846,1.531 0.403,0.153 10 CANL 2.529,1.376 2.959,1.529 0.430,0.153 10 CANH 2.127,1.004 2.008,1.445 2.008,1.445 1.836,1.445 false 2.242,1.004 2.307,1.445 2.307,1.445 2.514,1.445 false

Text in Illustration
*a Component without harness connected
(Combination Meter Assembly)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U159532E01
1.619,0.754 1.825,0.907 0.206,0.153 10 G1 0.097,0.075 0.255,0.227 0.158,0.152 10 *a 0.223,1.599 0.333,1.751 0.110,0.152 10 B 0.975,2.91 1.403,3.062 0.429,0.152 10 CANH 2.25,2.904 2.679,3.056 0.429,0.152 10 CANL 3.081,1.601 3.292,1.753 0.211,0.152 10 ET 0.642,2.366 0.515,1.682 0.515,1.682 0.353,1.682 false 2.839,2.366 2.839,1.682 2.839,1.682 3.059,1.682 false 1.801,2.634 1.698,2.992 1.698,2.992 1.497,2.992 false 1.914,2.634 2.031,2.992 2.031,2.992 2.231,2.992 false

Disconnect the combination meter assembly connector.

Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G1-31 (CANH) - G1-32 (CANL) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
G1-31 (CANH) - G1-20 (ET) G - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G1-32 (CANL) - G1-20 (ET) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G1-31 (CANH) - G1-1 (B) G - L HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G1-32 (CANL) - G1-1 (B) W - L LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




AIR CONDITIONING AMPLIFIER ASSEMBLY


U159655E03
2.885,0.875 2.74,0.292 2.74,0.292 2.469,0.292 false 3.052,0.885 3.271,0.302 3.271,0.302 3.583,0.302 false 5.177,1.469 5.5,1.667 0.323,0.198 10 false z1 2.979,1.469 3.375,1.677 0.396,0.208 10 false G34 0.104,0.021 0.427,0.24 0.323,0.219 10 false *a 2.073,0.219 2.708,0.427 0.635,0.208 10 false CANL 3.635,0.229 4.302,0.479 0.667,0.25 10 false CANH

Text in Illustration
*a Component without harness connected
(Air Conditioning Amplifier Assembly)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U159533E01
1.566,0.754 1.847,0.907 0.282,0.153 10 G34 0.097,0.075 0.255,0.227 0.158,0.152 10 *a 0.118,2.506 0.229,2.658 0.110,0.152 10 B 0.814,1.371 1.243,1.522 0.429,0.152 10 CANH 2.298,1.366 2.727,1.518 0.429,0.152 10 CANL 2.743,1.662 3.070,1.814 0.327,0.152 10 GND 1.801,2.377 1.622,1.459 1.622,1.459 1.327,1.459 false 1.914,2.375 1.996,1.449 1.996,1.449 2.276,1.449 false 2.145,2.361 2.424,1.748 2.424,1.748 2.705,1.748 false 0.58,2.583 0.244,2.583 false

Disconnect the air conditioning amplifier assembly connector.

Text in Illustration
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G34-11 (CANH) - G34-12 (CANL) V - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
G34-11 (CANH) - G34-14 (GND) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G34-12 (CANL) - G34-14 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G34-11 (CANH) - G34-21 (B) V - BE HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G34-12 (CANL) - G34-21 (B) W - BE LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher