After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Turn the power switch off before measuring the resistances between CAN main bus lines and between CAN branch lines.
Turn the power switch off before inspecting CAN bus lines for a ground short.
Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
This section describes the standard values for all CAN related components.
Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
CAN JUNCTION CONNECTOR LH (for LHD)
Check the CAN junction connector LH (instrument panel wire side).
Connection diagram
| *a | Front view of wire harness connector
(to CAN Junction Connector LH (Instrument Panel Wire Side)) |
*b | to Hybrid Vehicle Control Computer Assembly
(for V Bus) |
| *c | to DLC3
(for V Bus) |
*d | to CAN Junction Connector RH
(for V Bus) |
Check the connection diagram of the components which are connected to the CAN junction connector LH.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| G86-2 (CANH) | BE | Hybrid vehicle control computer assembly
(for V bus) |
| G86-13 (CANL) | W | |
| G86-3 (CANH) | GR | DLC3
(for V bus) |
| G86-14 (CANL) | W | |
| G86-4 (CANH) | SB | CAN junction connector RH
(for V bus) |
| G86-15 (CANL) | W |
Check the CAN junction connector LH (engine room main wire side).
Connection diagram
| *a | Front view of wire harness connector
(to CAN Junction Connector LH (Engine Room Main Wire Side)) |
*b | to ECM
(for V Bus) |
| *c | to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
(for V Bus) |
- | - |
Check the connection diagram of the components which are connected to the CAN junction connector LH.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| A74-9 (CANH) | L | ECM
(for V bus) |
| A74-20 (CANL) | W | |
| A74-10 (CANH) | B | Brake booster with master cylinder assembly (Skid control ECU)
(for V bus) |
| A74-21 (CANL) | W |
CAN JUNCTION CONNECTOR LH (for RHD)
Check the CAN junction connector LH (instrument panel wire side).
Connection diagram
| *a | Front view of wire harness connector
(to CAN Junction Connector LH (Instrument Panel Wire Side)) |
*b | to Hybrid Vehicle Control Computer Assembly
(for V Bus) |
| *c | to Smart Key ECU Assembly (Certification ECU)
(for V Bus) |
*d | to CAN Junction Connector RH
(for V Bus) |
Check the connection diagram of the components which are connected to the CAN junction connector LH.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| G86-2 (CANH) | BE | Hybrid vehicle control computer assembly
(for V bus) |
| G86-13 (CANL) | W | |
| G86-3 (CANH) | L | Smart key ECU assembly (Certification ECU)
(for V bus) |
| G86-14 (CANL) | W | |
| G86-4 (CANH) | SB | CAN junction connector RH
(for V bus) |
| G86-15 (CANL) | W |
Check the CAN junction connector LH (engine room main wire side).
Connection diagram
| *a | Front view of wire harness connector
(to CAN Junction Connector LH (Engine Room Main Wire Side)) |
*b | to ECM
(for V Bus) |
| *c | to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
(for V Bus) |
- | - |
Check the connection diagram of the components which are connected to the CAN junction connector LH.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| A74-9 (CANH) | L | ECM
(for V bus) |
| A74-20 (CANL) | W | |
| A74-10 (CANH) | B | Brake booster with master cylinder assembly (Skid control ECU)
(for V bus) |
| A74-21 (CANL) | W |
CAN JUNCTION CONNECTOR RH (for LHD)
Check the CAN junction connector RH.
Connection diagram
| *a | Front view of wire harness connector
(to CAN Junction Connector RH) |
*b | to Spiral Cable with Sensor Sub-assembly (Steering Sensor)
(for V Bus) |
| *c | to Smart Key ECU Assembly (Certification ECU)
(for V Bus) |
*d | to Airbag Sensor Assembly
(for V Bus) |
| *e | to Power Steering ECU Assembly
(for V Bus) |
*f | to Combination Meter Assembly
(for V Bus) |
| *g | to Air Conditioning Amplifier Assembly
(for V Bus) |
*h | to Main Body ECU (Multiplex Network Body ECU)
(for V Bus) |
| *i | to CAN Junction Connector LH
(for V Bus) |
- | - |
Check the connection diagram of the components which are connected to the CAN junction connector RH.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| G72-1 (CANH) | P | Spiral cable with sensor sub-assembly (Steering sensor)
(for V bus) |
| G72-12 (CANL) | W | |
| G72-3 (CANH) | L | Smart key ECU assembly (Certification ECU)
(for V bus) |
| G72-14 (CANL) | W | |
| G72-4 (CANH) | B | Airbag sensor assembly
(for V bus) |
| G72-15 (CANL) | W | |
| G72-6 (CANH) | LG | Power steering ECU assembly
(for V bus) |
| G72-17 (CANL) | W | |
| G72-7 (CANH) | G | Combination meter assembly
(for V bus) |
| G72-18 (CANL) | W | |
| G72-8 (CANH) | V | Air conditioning amplifier assembly
(for V bus) |
| G72-19 (CANL) | W | |
| G72-9 (CANH) | BE | Main body ECU (Multiplex network body ECU)
(for V bus) |
| G72-20 (CANL) | W | |
| G72-10 (CANH) | SB | CAN junction connector LH
(for V bus) |
| G72-21 (CANL) | W |
CAN JUNCTION CONNECTOR RH (for RHD)
Check the CAN junction connector RH.
Connection diagram
| *a | Front view of wire harness connector
(to CAN Junction Connector RH) |
*b | to Spiral Cable with Sensor Sub-assembly (Steering Sensor)
(for V Bus) |
| *c | to Airbag Sensor Assembly
(for V Bus) |
*d | to Power Steering ECU Assembly
(for V Bus) |
| *e | to Combination Meter Assembly
(for V Bus) |
*f | to Air Conditioning Amplifier Assembly
(for V Bus) |
| *g | to Main Body ECU (Multiplex Network Body ECU)
(for V Bus) |
*h | to CAN Junction Connector LH
(for V Bus) |
| *i | to DLC3
(for V Bus) |
- | - |
Check the connection diagram of the components which are connected to the CAN junction connector RH.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| G72-1 (CANH) | P | Spiral cable with sensor sub-assembly (Steering sensor)
(for V bus) |
| G72-12 (CANL) | W | |
| G72-4 (CANH) | B | Airbag sensor assembly
(for V bus) |
| G72-15 (CANL) | W | |
| G72-6 (CANH) | LG | Power steering ECU assembly
(for V bus) |
| G72-17 (CANL) | W | |
| G72-7 (CANH) | G | Combination meter assembly
(for V bus) |
| G72-18 (CANL) | W | |
| G72-8 (CANH) | V | Air conditioning amplifier assembly
(for V bus) |
| G72-19 (CANL) | W | |
| G72-9 (CANH) | BE | Main body ECU (Multiplex network body ECU)
(for V bus) |
| G72-20 (CANL) | W | |
| G72-10 (CANH) | SB | CAN junction connector LH
(for V bus) |
| G72-21 (CANL) | W | |
| G72-11 (CANH) | GR | DLC3
(for V bus) |
| G72-22 (CANH) | W |
CAN JUNCTION CONNECTOR LH
Check the CAN junction connector LH (engine room main wire side).
Connection diagram
| *a | Front view of wire harness connector
(to CAN Junction Connector LH (Engine Room Main Wire Side)) |
*b | to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
(for Sub Bus 15) |
| *c | to ECM
(for Sub Bus 15) |
- | - |
Check the connection diagram of the components which are connected to the CAN junction connector LH.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| A74-1 (CANH) | L | Brake booster with master cylinder assembly (Skid control ECU)
(for Sub bus 15) |
| A74-12 (CANL) | W | |
| A74-3 (CANH) | B | ECM
(for Sub bus 15) |
| A74-14 (CANL) | W |
Check the CAN junction connector LH (instrument panel wire side).
Connection diagram
| *a | Front view of wire harness connector
(to CAN Junction Connector LH (Instrument Panel Wire Side)) |
*b | to Hybrid Vehicle Control Computer Assembly
(for Sub Bus 15) |
Check the connection diagram of the components which are connected to the CAN junction connector LH.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| G86-10 (CANH) | R | Hybrid vehicle control computer assembly
(for Sub bus 15) |
| G86-21 (CANL) | W |
DLC3
Disconnect the cable from the negative (-) auxiliary battery terminal.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G4-6 (CANH) - G4-14 (CANL) | GR - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| G4-6 (CANH) - G4-4 (CG) | GR - P | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G4-14 (CANL) - G4-4 (CG) | W - P | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G4-6 (CANH) - G4-16 (BAT) | GR - SB | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| G4-14 (CANL) - G4-16 (BAT) | W - SB | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
HYBRID VEHICLE CONTROL COMPUTER ASSEMBLY
| *a | Component without harness connected
(Hybrid Vehicle Control Computer Assembly) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the G81 hybrid vehicle control computer assembly connector.
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control Computer Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G81-25 (CA1H) - G81-24 (CA1L) | BE - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| G81-25 (CA1H) - G80-6 (E1) | BE - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G81-24 (CA1L) - G80-6 (E1) | W - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G81-25 (CA1H) - G81-3 (BATT) | BE - BE | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| G81-24 (CA1L) - G81-3 (BATT) | W - BE | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G81-31 (CA3P) - G81-30 (CA3N) | R - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| G81-31 (CA3P) - G80-6 (E1) | R - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G81-30 (CA3N) - G80-6 (E1) | W - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G81-31 (CA3P) - G81-3 (BATT) | R - BE | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| G81-30 (CA3N) - G81-3 (BATT) | W - BE | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
ECM
| *A | for LHD | *B | for RHD |
| *a | Component without harness connected
(ECM) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the A40 and C9 or C10 ECM connectors.
| *A | for LHD | *B | for RHD |
| *a | Front view of wire harness connector
(to ECM) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A40-13 (CANH) - A40-26 (CANL) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| A40-13 (CANH) - C10-16 (E1)*1
A40-13 (CANH) - C9-16 (E1)*2 |
L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A40-26 (CANL) - C10-16 (E1)*1
A40-26 (CANL) - C9-16 (E1)*2 |
W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A40-13 (CANH) - A40-1 (BATT) | L - Y | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A40-26 (CANL) - A40-1 (BATT) | W - Y | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A40-12 (CANP) - A40-25 (CANN) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| A40-12 (CANP) - C10-16 (E1)*1
A40-12 (CANP) - C9-16 (E1)*2 |
B - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A40-25 (CANN) - C10-16 (E1)*1
A40-25 (CANN) - C9-16 (E1)*2 |
W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A40-12 (CANP) - A40-1 (BATT) | B - Y | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A40-25 (CANN) - A40-1 (BATT) | W - Y | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
*1: for LHD
*2: for RHD
BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU)
| *a | Component without harness connected
(Brake Booster with Master Cylinder Assembly (Skid Control ECU)) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the A41 brake booster with master cylinder assembly (skid control ECU) connector.
| *a | Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly (Skid Control ECU)) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A41-37 (CA1H) - A41-38 (CA1L) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A41-37 (CA1H) - A41-28 (GND) | B - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A41-38 (CA1L) - A41-28 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A41-37 (CA1H) - A41-14 (BI) | B - W | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A41-38 (CA1L) - A41-14 (BI) | W - W | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A41-35 (CA2H) - A41-34 (CA2L) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| A41-35 (CA2H) - A41-28 (GND) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A41-34 (CA2L) - A41-28 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A41-35 (CA2H) - A41-14 (BI) | L - W | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A41-34 (CA2L) - A41-14 (BI) | W - W | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
AIRBAG SENSOR ASSEMBLY
| *a | Component without harness connected
(Airbag Sensor Assembly) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the G18 airbag sensor assembly connector.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G18-13 (CANH) - G18-22 (CANL) | B - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| G18-13 (CANH) - G18-25 (E1) | B - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G18-22 (CANL) - G18-25 (E1) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G18-13 (CANH) - G4-16 (BAT) | B - SB | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| G18-22 (CANL) - G4-16 (BAT) | W - SB | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
| *A | Component without harness connected
(Main Body ECU (Multiplex Network Body ECU) with 1 connector) |
*B | for LHD |
| *C | for RHD | - | - |
| *1 | Main Body ECU (Multiplex Network Body ECU) | - | - |
| *A | Component without harness connected
(Main Body ECU (Multiplex Network Body ECU) with 2 connectors) |
- | - |
| *1 | Main Body ECU (Multiplex Network Body ECU) | - | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the G59 main body ECU (multiplex network body ECU) connector.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU)) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G59-14 (CANH) - G59-13 (CANL) | BE - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| G59-14 (CANH) - G4-4 (CG) | BE - P | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G59-13 (CANL) - G4-4 (CG) | W - P | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G59-14 (CANH) - G4-16 (BAT) | BE - SB | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| G59-13 (CANL) - G4-16 (BAT) | W - SB | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY (STEERING SENSOR)
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the G30 spiral cable with sensor sub-assembly (steering sensor) connector.
| *a | Front view of wire harness connector
(to Spiral Cable with Sensor Sub-assembly (Steering Sensor)) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G30-4 (CANH) - G30-3 (CANL) | P - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| G30-4 (CANH) - G30-2 (ESS) | P - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G30-3 (CANL) - G30-2 (ESS) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G30-4 (CANH) - G30-6 (BAT) | P - B | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| G30-3 (CANL) - G30-6 (BAT) | W - B | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
POWER STEERING ECU ASSEMBLY
| *a | Component without harness connected
(Power Steering ECU Assembly) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the A33 and G6 power steering ECU assembly connectors.
| *a | Front view of wire harness connector
(to Power Steering ECU Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G6-7 (CANH) - G6-8 (CANL) | LG - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| G6-7 (CANH) - A33-2 (PGND) | LG - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G6-8 (CANL) - A33-2 (PGND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G6-7 (CANH) - A33-1 (PIG) | LG - W | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| G6-8 (CANL) - A33-1 (PIG) | W - W | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
SMART KEY ECU ASSEMBLY (CERTIFICATION ECU)
| *a | Component without harness connected
(Smart Key ECU Assembly (Certification ECU)) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the G77 and G79 smart key ECU assembly (certification ECU) connectors.
| *a | Rear view of wire harness connector
(to Smart Key ECU Assembly (Certification ECU)) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G79-14 (CANH) - G79-15 (CANL) | L - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| G79-14 (CANH) - G77-11 (E) | L - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G79-15 (CANL) - G77-11 (E) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G79-14 (CANH) - G77-2 (+B) | L - B | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| G79-15 (CANL) - G77-2 (+B) | W - B | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
COMBINATION METER ASSEMBLY
| *a | Component without harness connected
(Combination Meter Assembly) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the G1 combination meter assembly connector.
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G1-31 (CANH) - G1-32 (CANL) | G - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| G1-31 (CANH) - G1-20 (ET) | G - BR | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G1-32 (CANL) - G1-20 (ET) | W - BR | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G1-31 (CANH) - G1-1 (B) | G - L | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| G1-32 (CANL) - G1-1 (B) | W - L | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
AIR CONDITIONING AMPLIFIER ASSEMBLY
| *a | Component without harness connected
(Air Conditioning Amplifier Assembly) |
- | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the G34 air conditioning amplifier assembly connector.
| *a | Front view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G34-11 (CANH) - G34-12 (CANL) | V - W | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| G34-11 (CANH) - G34-14 (GND) | V - W-B | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G34-12 (CANL) - G34-14 (GND) | W - W-B | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G34-11 (CANH) - G34-21 (B) | V - BE | HIGH-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| G34-12 (CANL) - G34-21 (B) | W - BE | LOW-level CAN bus line - Auxiliary battery positive (+) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |