Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2015.11
RM2170E _57 Power Source / Network _057033 NETWORKING _0278068 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Power Steering ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Power Steering ECU Communication Stop Mode Either condition is met:
·

"Power Steering (EPS)" is not displayed on the CAN Bus Check screen of the GTS (See page (Click here))

·

Communication system DTCs (DTCs that start with U) that correspond to "Power Steering ECU Communication Stop Mode" in "DTC Combination Table" are output (See page (Click here))


·

Power steering ECU assembly branch line or connector

·

Power source circuit of power steering ECU assembly

·

Power steering ECU assembly ground circuit

·

Power steering ECU assembly



WIRING DIAGRAM

C349991E02
3.854,1.281 4.198,0.667 4.198,0.667 4.479,0.667 false 2,0.896 2.177,0.896 2.177,0.896 2.177,1.281 false 5.021,3.323 5.115,3.469 0.094,0.146 10 false 2 4.396,3.573 4.854,3.719 0.458,0.146 10 false PGND 3.479,3.583 3.667,3.729 0.188,0.146 10 false IG 1.125,5 3.021,5.229 1.896,0.229 10 false : CAN Main Bus Line (CANH) 1.125,5.406 3.021,5.635 1.896,0.229 10 false : CAN Main Bus Line (CANL) 4.26,5.01 5.979,5.24 1.719,0.229 10 false : CAN Branch Line (CANH) 4.26,5.406 5.958,5.635 1.698,0.229 10 false : CAN Branch Line (CANL) 1.083,3.76 1.917,3.938 0.833,0.177 10 false Trouble Area 3.646,3.292 4.073,3.438 0.427,0.146 10 false CANH 4.271,3.292 4.677,3.438 0.406,0.146 10 false CANL 3.656,3.021 3.781,3.177 0.125,0.156 10 false 7 3.219,3.406 3.323,3.552 0.104,0.146 10 false 1 4.594,3.021 4.698,3.177 0.104,0.156 10 false 8 4.521,0.583 6.427,0.917 1.906,0.333 10 false CAN Junction Connector RH 0.167,0.802 2,0.979 1.833,0.177 10 false CAN Junction Connector LH 2.417,3.802 2.927,4.115 0.51,0.313 10 false ECU-IG NO. 2 0.708,2.219 1.156,2.365 0.448,0.146 10 false 120 Ω 6.125,2.208 6.573,2.354 0.448,0.146 10 false 120 Ω 2.646,0.542 3.042,0.708 0.396,0.167 10 false DLC3 5.781,2.823 7.01,3.177 1.229,0.354 10 false Combination Meter Assembly 0.688,2.833 1.052,2.979 0.365,0.146 10 false ECM 0.104,0.073 1.51,0.313 1.406,0.24 12 false V Bus (for LHD): 3.135,3.646 3.354,3.792 0.219,0.146 10 false G6 3.833,3.094 4.052,3.24 0.219,0.146 10 false G6 4.26,3.083 4.479,3.229 0.219,0.146 10 false G6 4.917,3.563 5.188,3.708 0.271,0.146 10 false A33 3.177,4.25 5.125,4.427 1.948,0.177 10 false Power Steering ECU Assembly

C251624E11
4.854,1.281 5.198,0.667 5.198,0.667 5.479,0.667 false 2.823,1.281 3.167,0.51 3.167,0.51 3.448,0.51 false 4.292,3.375 4.385,3.521 0.094,0.146 10 false 2 3.688,3.563 4.146,3.708 0.458,0.146 10 false PGND 2.771,3.656 2.958,3.802 0.188,0.146 10 false IG 1.115,5 3.01,5.229 1.896,0.229 10 false : CAN Main Bus Line (CANH) 1.115,5.406 3.01,5.635 1.896,0.229 10 false : CAN Main Bus Line (CANL) 4.25,5.021 5.969,5.25 1.719,0.229 10 false : CAN Branch Line (CANH) 4.25,5.417 5.948,5.646 1.698,0.229 10 false : CAN Branch Line (CANL) 4.958,3.75 5.792,3.917 0.833,0.167 10 false Trouble Area 3.021,3.292 3.448,3.438 0.427,0.146 10 false CANH 3.5,3.292 3.906,3.458 0.406,0.167 10 false CANL 2.938,3.063 3.063,3.219 0.125,0.156 10 false 7 2.51,3.458 2.615,3.604 0.104,0.146 10 false 1 3.885,3.063 3.99,3.219 0.104,0.156 10 false 8 5.521,0.583 6.396,1.229 0.875,0.646 10 false CAN Junction Connector LH 3.49,0.427 4.427,1.073 0.938,0.646 10 false CAN Junction Connector RH 1.708,3.802 2.219,4.219 0.51,0.417 10 false ECU-IG NO. 2 0.698,2.208 1.146,2.354 0.448,0.146 10 false 120 Ω 6.115,2.198 6.563,2.344 0.448,0.146 10 false 120 Ω 2.063,0.552 2.458,0.719 0.396,0.167 10 false DLC3 0.385,2.823 1.615,3.177 1.229,0.354 10 false Combination Meter Assembly 6.208,2.813 6.573,2.958 0.365,0.146 10 false ECM 0.094,0.063 1.5,0.302 1.406,0.24 12 false V Bus (for RHD): 2.438,3.646 2.656,3.792 0.219,0.146 10 false G6 3.135,3.073 3.354,3.219 0.219,0.146 10 false G6 3.542,3.073 3.76,3.219 0.219,0.146 10 false G6 4.208,3.563 4.479,3.708 0.271,0.146 10 false A33 2.469,4.26 4.417,4.438 1.948,0.177 10 false Power Steering ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control main switch (ON/OFF switch), wait at least 60 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more.

·

After the repair, perform the CAN bus check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (POWER STEERING ECU ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U159500E01
1.535,0.368 1.743,0.509 0.208,0.141 10 G6 0.07,0.069 0.232,0.210 0.162,0.141 10 *a 2.351,2.531 2.740,2.672 0.389,0.141 10 CANL 2.457,2.011 2.877,2.151 0.420,0.141 10 CANH 1.969,2.611 2.328,2.611 false 1.798,2.549 2.258,2.089 2.258,2.089 2.436,2.089 false

Disconnect the G6 power steering ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G6-7 (CANH) - G6-8 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (POWER STEERING ECU ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U159417E01
0.146,0.124 0.341,0.310 0.195,0.186 10 *a 2.522,0.745 2.966,0.901 0.444,0.156 10 PGND 2.268,1.716 2.268,0.836 2.268,0.836 2.492,0.836 false 1.631,0.699 1.895,0.842 0.264,0.143 10 A33

Disconnect the A33 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A33-2 (PGND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


c.

Reconnect the cable to the negative (-) auxiliary battery terminal.


d.
U159501E01
1.54,0.35 1.745,0.503 0.205,0.153 10 G6 0.604,2.289 0.778,2.442 0.174,0.153 10 IG 0.132,0.099 0.305,0.252 0.173,0.153 10 *a 1.359,2.369 0.813,2.369 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G6-1 (IG) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU Assembly)



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)