Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2015.11
RM2170E _57 Power Source / Network _057033 NETWORKING _0278068 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Hybrid Vehicle Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Hybrid Vehicle Control ECU Communication Stop Mode Either condition is met:
·

"Power Management2" and/or "Hybrid Vehicle Control" is not displayed on the CAN Bus Check screen of the GTS (See page (Click here)).

·

Communication system DTCs (DTCs that start with U) that correspond to "Hybrid Vehicle Control ECU Communication Stop Mode" in "DTC Combination Table" are output (See page (Click here)).


·

Hybrid vehicle control computer assembly branch line or connector

·

Power source circuit of hybrid vehicle control computer assembly

·

Hybrid vehicle control computer assembly ground circuit

·

Hybrid vehicle control computer assembly



WIRING DIAGRAM

C252854E19
2.51,1.281 2.26,0.646 2.26,0.646 2.021,0.646 false 4.333,1.281 4.083,0.646 4.083,0.646 3.844,0.646 false 6.24,2.823 6.583,2.99 0.344,0.167 10 false ECM 4.781,0.521 5.156,0.667 0.375,0.146 10 false DLC3 1.25,3.958 2.104,4.135 0.854,0.177 10 false Trouble Area 0.104,0 1.354,0.198 1.25,0.198 12 false V Bus (for LHD): 0.271,2.844 1.51,3.208 1.24,0.365 10 false Combination Meter Assembly 1.135,0.542 2.042,1.188 0.906,0.646 10 false CAN Junction Connector RH 2.688,4.135 5.781,4.521 3.094,0.385 10 false Hybrid Vehicle Control Computer Assembly 3.052,3.781 3.323,3.927 0.271,0.146 10 false A71 3.052,3.406 3.344,3.583 0.292,0.177 10 false A72 3.75,3.083 4.031,3.229 0.281,0.146 10 false G81 4.135,3.083 4.417,3.229 0.281,0.146 10 false G81 2.24,3.896 3.094,4.302 0.854,0.406 10 false IGCT NO. 2 3.677,3.271 4.063,3.427 0.385,0.156 10 false CA1H 4.125,3.271 4.49,3.448 0.365,0.177 10 false CA1L 3.385,3.385 3.656,3.531 0.271,0.146 10 false +B1 3.375,3.771 3.688,3.948 0.313,0.177 10 false +B2 4.573,3.583 4.76,3.74 0.188,0.156 10 false E1 4.927,3.375 5.063,3.552 0.135,0.177 10 false 6 3.146,3.219 3.313,3.365 0.167,0.146 10 false 4 3.146,3.604 3.292,3.75 0.146,0.146 10 false 1 3.51,3.094 3.677,3.24 0.167,0.146 10 false 25 4.49,3.083 4.656,3.229 0.167,0.146 10 false 24 6.125,2.229 6.521,2.406 0.396,0.177 10 false 120 Ω 0.729,2.229 1.125,2.406 0.396,0.177 10 false 120 Ω 1.104,4.99 3.021,5.313 1.917,0.323 10 false : CAN Main Bus Line (CANH) 1.104,5.396 3.021,5.719 1.917,0.323 10 false : CAN Main Bus Line (CANL) 4.26,4.979 6.021,5.302 1.76,0.323 10 false : CAN Branch Line (CANH) 4.26,5.417 6,5.74 1.74,0.323 10 false : CAN Branch Line (CANL) 4.833,3.563 5.115,3.719 0.281,0.156 10 false G80 2.927,0.552 3.833,1.198 0.906,0.646 10 false CAN Junction Connector LH

C251627E08
1.823,1.281 1.573,0.646 1.573,0.646 1.333,0.646 false 4.323,1.281 4.073,0.646 4.073,0.646 3.844,0.646 false 6.219,2.813 6.563,2.979 0.344,0.167 10 false ECM 2.083,0.542 2.458,0.688 0.375,0.146 10 false DLC3 1.229,3.979 2.083,4.156 0.854,0.177 10 false Trouble Area 0.094,0.042 1.448,0.24 1.354,0.198 12 false V Bus (for RHD): 0.375,2.823 1.615,3.167 1.24,0.344 10 false Combination Meter Assembly 0.417,0.542 1.323,1.188 0.906,0.646 10 false CAN Junction Connector RH 2.781,4.156 5.51,4.406 2.729,0.25 10 false Hybrid Vehicle Control Computer Assembly 3.042,3.781 3.344,3.948 0.302,0.167 10 false A71 3.042,3.396 3.333,3.573 0.292,0.177 10 false A72 3.74,3.083 4.021,3.229 0.281,0.146 10 false G81 4.135,3.073 4.417,3.219 0.281,0.146 10 false G81 2.229,3.906 3.156,4.208 0.927,0.302 10 false IGCT NO. 2 3.677,3.281 4.063,3.438 0.385,0.156 10 false CA1H 4.156,3.281 4.521,3.458 0.365,0.177 10 false CA1L 3.385,3.385 3.656,3.531 0.271,0.146 10 false +B1 3.375,3.781 3.646,3.927 0.271,0.146 10 false +B2 4.573,3.583 4.76,3.74 0.188,0.156 10 false E1 4.927,3.375 5.031,3.521 0.104,0.146 10 false 6 3.146,3.198 3.281,3.365 0.135,0.167 10 false 4 3.135,3.604 3.26,3.76 0.125,0.156 10 false 1 3.51,3.083 3.677,3.229 0.167,0.146 10 false 25 4.49,3.073 4.656,3.219 0.167,0.146 10 false 24 6.177,2.208 6.573,2.385 0.396,0.177 10 false 120 Ω 0.729,2.198 1.125,2.375 0.396,0.177 10 false 120 Ω 1.115,5.01 3.031,5.333 1.917,0.323 10 false : CAN Main Bus Line (CANH) 1.115,5.417 3.031,5.74 1.917,0.323 10 false : CAN Main Bus Line (CANL) 4.26,4.99 6.021,5.313 1.76,0.323 10 false : CAN Branch Line (CANH) 4.26,5.417 6,5.74 1.74,0.323 10 false : CAN Branch Line (CANL) 4.833,3.563 5.115,3.719 0.281,0.156 10 false G80 2.927,0.552 3.833,1.198 0.906,0.646 10 false CAN Junction Connector LH

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control main switch (ON/OFF switch), wait at least 60 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more.

·

After the repair, perform CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (HYBRID VEHICLE CONTROL COMPUTER ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U183187E02
2.479,2.51 1.656,2.219 false 2.427,2.521 1.677,2.469 false 2.51,2.958 2.792,3.104 0.281,0.146 10 false G81 1.26,2.094 1.625,2.271 0.365,0.177 10 false CA1L 1.25,2.375 1.635,2.552 0.385,0.177 10 false CA1H 0.156,0.052 0.354,0.219 0.198,0.167 10 false *a

Disconnect the G81 hybrid vehicle control computer assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Value
G81-25 (CA1H) - G81-24 (CA1L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control Computer Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (HYBRID VEHICLE CONTROL COMPUTER ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)
a.

Reconnect the G81 hybrid vehicle control computer assembly connector.


b.
U183523E01
2.473,0.965 2.753,1.118 0.280,0.153 10 G81 1.901,0.965 2.181,1.118 0.280,0.153 10 G80 1.306,0.961 1.586,1.114 0.280,0.153 10 A72 1.218,2.575 1.409,2.728 0.191,0.153 10 E1 0.663,0.961 0.943,1.114 0.280,0.153 10 A71 0.122,0.091 0.300,0.244 0.178,0.153 10 *a 1.84,2.656 1.44,2.656 false

Disconnect the G80 hybrid vehicle control computer assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Value
G80-6 (E1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control Computer Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND TERMINAL)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.

Reconnect the G80 hybrid vehicle control computer assembly connector.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.
U183293E01
2.488,0.828 2.772,0.981 0.284,0.153 10 G81 1.911,0.828 2.195,0.981 0.284,0.153 10 G80 1.279,0.828 1.563,0.981 0.284,0.153 10 A72 0.675,0.828 0.959,0.981 0.284,0.153 10 A71 0.1,0.061 0.278,0.214 0.179,0.153 10 *a 0.551,2.422 0.835,2.575 0.284,0.153 10 +B2 1.145,2.422 1.429,2.575 0.284,0.153 10 +B1 1.001,1.693 0.736,2.414 false 1.395,1.695 1.31,2.406 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Value
A72-4 (+B1) - Body ground Power switch on (IG) 11 to 14 V
A71-1 (+B2) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Component with harness connected
(Hybrid Vehicle Control Computer Assembly)



OK

REPLACE HYBRID VEHICLE CONTROL COMPUTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE TERMINAL)