Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2014.12–2015.11
RM2170E _57 Power Source / Network _057033 NETWORKING _0278068 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check CAN Bus Lines for Short Circuit (LHD Models)  


DESCRIPTION

There may be a short circuit between the V bus main lines and/or CAN branch lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.

Symptom Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.
·

Short in CAN main bus lines

·

Short in CAN branch lines

·

ECM

·

Brake booster with master cylinder assembly (Skid control ECU)

·

Main body ECU (Multiplex network body ECU)

·

Air conditioning amplifier assembly

·

Power steering ECU assembly

·

Smart key ECU assembly (Certification ECU)

·

Airbag sensor assembly

·

Spiral cable with sensor sub-assembly (Steering sensor)

·

Hybrid vehicle control computer assembly

·

Combination meter assembly

·

CAN junction connector LH

·

CAN junction connector RH



WIRING DIAGRAM

C260980E06
3.958,7.969 5.688,8.156 1.729,0.188 10 false : CAN Branch Line (CANH) 3.948,8.375 5.677,8.563 1.729,0.188 10 false : CAN Branch Line (CANL) 0.823,7.99 2.74,8.177 1.917,0.188 10 false : CAN Main Bus Line (CANH) 0.823,8.396 2.74,8.583 1.917,0.188 10 false : CAN Main Bus Line (CANL) 3.469,0.219 3.885,0.406 0.417,0.188 10 false 120 Ω 2.792,0.927 3.198,1.094 0.406,0.167 10 false CANL 0.427,0.448 0.792,0.615 0.365,0.167 10 false G1 4.135,1.438 4.354,1.656 0.219,0.219 10 false G 3,1.438 3.198,1.604 0.198,0.167 10 false W 0.677,0.448 2.531,0.646 1.854,0.198 10 false Combination Meter Assembly 0.135,0.063 1.99,0.26 1.854,0.198 12 false V Bus: 4.135,0.927 4.573,1.094 0.438,0.167 10 false CANH 4.083,1.229 4.427,1.448 0.344,0.219 10 false 31 2.99,1.24 3.302,1.448 0.313,0.208 10 false 32 5.208,0.563 6.417,0.75 1.208,0.188 10 false x: Suspected Area 4.823,2.042 6.813,2.292 1.99,0.25 10 false CAN Junction Connector RH 5.938,3.5 6.344,3.667 0.406,0.167 10 false CANL 5.906,2.917 6.344,3.083 0.438,0.167 10 false CANH 5.938,5.469 6.344,5.635 0.406,0.167 10 false CANL 5.927,4.896 6.365,5.063 0.438,0.167 10 false CANH 5.656,4.875 5.885,5.042 0.229,0.167 10 false 11 5,4.792 5.115,4.958 0.115,0.167 10 false V 4.99,5.552 5.156,5.719 0.167,0.167 10 false W 5.667,5.479 5.917,5.698 0.25,0.219 10 false 12 4.479,4.906 4.74,5.167 0.26,0.26 10 false 8 4.427,5.458 4.677,5.729 0.25,0.271 10 false 19 2.75,3.948 2.948,4.177 0.198,0.229 10 false 4 2.677,4.563 2.906,4.771 0.229,0.208 10 false 15 4.458,2.896 4.698,3.115 0.24,0.219 10 false 3 4.417,3.49 4.677,3.792 0.26,0.302 10 false 14 5.031,2.708 5.177,2.875 0.146,0.167 10 false L 5,3.625 5.146,3.792 0.146,0.167 10 false W 5.677,2.906 5.865,3.073 0.188,0.167 10 false 14 5.698,3.49 5.885,3.656 0.188,0.167 10 false 15 5.25,3.76 5.563,3.969 0.313,0.208 10 false G79 5.573,3.76 7.083,4.417 1.51,0.656 10 false Smart Key ECU Assembly (Certification ECU) 5.208,5.729 5.5,5.906 0.292,0.177 10 false G34 5.531,5.729 7.115,6.104 1.583,0.375 10 false Air Conditioning Amplifier Assembly 0.479,4.823 2.052,5.177 1.573,0.354 10 false Airbag Sensor Assembly 1.042,4.531 1.448,4.698 0.406,0.167 10 false CANL 1.021,3.969 1.458,4.135 0.438,0.167 10 false CANH 2.125,3.781 2.323,4.031 0.198,0.25 10 false B 2.115,4.677 2.313,4.875 0.198,0.198 10 false W 0.146,4.823 0.448,5 0.302,0.177 10 false G18 1.542,3.979 1.833,4.208 0.292,0.229 10 false 13 1.552,4.542 1.74,4.708 0.188,0.167 10 false 22 4.51,2.042 4.875,2.323 0.365,0.281 10 false G72 3,1.677 3.292,1.917 0.292,0.24 10 false 18 4.146,1.677 4.417,1.875 0.271,0.198 10 false 7 2.938,7.229 3.24,7.5 0.302,0.271 10 false 21 4.177,7.219 4.563,7.521 0.385,0.302 10 false 10 2.792,2.104 3,2.271 0.208,0.167 10 false 1 2.719,2.688 2.969,2.927 0.25,0.24 10 false 12 1.063,2.698 1.469,2.865 0.406,0.167 10 false CANL 2.125,2.771 2.281,2.938 0.156,0.167 10 false W 0.104,3 0.469,3.167 0.365,0.167 10 false G30 1.052,2.104 1.49,2.271 0.438,0.167 10 false CANH 1.583,2.135 1.802,2.333 0.219,0.198 10 false 4 1.583,2.677 1.823,2.885 0.24,0.208 10 false 3 2.146,1.958 2.323,2.104 0.177,0.146 10 false P 0.448,2.99 2.615,3.438 2.167,0.448 10 false Spiral Cable with Sensor Sub-assembly (Steering Sensor)

C318515E02
3.979,8.021 5.708,8.208 1.729,0.188 10 false : CAN Branch Line (CANH) 3.979,8.427 5.708,8.615 1.729,0.188 10 false : CAN Branch Line (CANL) 0.76,8.01 2.677,8.198 1.917,0.188 10 false : CAN Main Bus Line (CANH) 0.76,8.417 2.677,8.604 1.917,0.188 10 false : CAN Main Bus Line (CANL) 1.844,5.156 2.031,5.417 0.188,0.26 10 false W 0.75,3.448 1.156,3.615 0.406,0.167 10 false CA1L 0.74,2.885 1.177,3.052 0.438,0.167 10 false CA1H 0.531,4.885 0.938,5.052 0.406,0.167 10 false CANL 0.646,4.542 1.083,4.708 0.438,0.167 10 false CANH 4.396,1.646 4.604,1.813 0.208,0.167 10 false 1 4.375,2.427 4.604,2.698 0.229,0.271 10 false 12 1.281,3.458 1.49,3.625 0.208,0.167 10 false 24 2.646,4.417 2.917,4.635 0.271,0.219 10 false 3 2.563,5.198 2.948,5.479 0.385,0.281 10 false 14 1.281,2.896 1.458,3.063 0.177,0.167 10 false 25 1.052,5.094 1.25,5.26 0.198,0.167 10 false 14 1.219,4.531 1.396,4.698 0.177,0.167 10 false 6 4.948,0.198 6.156,0.385 1.208,0.188 10 false x: Suspected Area 0.042,3.75 0.385,3.948 0.344,0.198 10 false G81 0.354,3.75 2.104,4.177 1.75,0.427 10 false Hybrid Vehicle Control Computer Assembly 0.271,5.198 0.594,5.385 0.323,0.188 10 false G4 0.531,5.198 0.927,5.385 0.396,0.188 10 false DLC3 5.979,2.323 6.385,2.49 0.406,0.167 10 false CANL 5.156,2.406 5.313,2.573 0.156,0.167 10 false W 5,2.604 5.333,2.813 0.333,0.208 10 false G59 5.948,1.76 6.385,1.927 0.438,0.167 10 false CANH 5.688,1.76 5.896,1.927 0.208,0.167 10 false 14 5.688,2.344 5.896,2.51 0.208,0.167 10 false 13 5.167,1.635 5.458,1.917 0.292,0.281 10 false R 5.333,2.604 7.073,3.146 1.74,0.542 10 false Main Body ECU (Multiplex Network Body ECU) 1.802,4.417 2.167,4.677 0.365,0.26 10 false GR 4.365,3.438 4.594,3.729 0.229,0.292 10 false 10 4.375,4.292 4.583,4.458 0.208,0.167 10 false 21 5.156,4.26 5.344,4.521 0.188,0.26 10 false W 5.177,3.49 5.365,3.729 0.188,0.24 10 false B 5.917,3.615 6.354,3.781 0.438,0.167 10 false CA1H 5.948,4.177 6.354,4.344 0.406,0.167 10 false CA1L 5.677,3.604 5.917,3.844 0.24,0.24 10 false 37 5.698,4.188 5.927,4.417 0.229,0.229 10 false 38 5.365,4.5 7.135,5.021 1.771,0.521 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 5.042,4.5 5.365,4.688 0.323,0.188 10 false A41 0.354,1.979 1.688,2.344 1.333,0.365 10 false Power Steering ECU Assembly 0.719,1.688 1.125,1.854 0.406,0.167 10 false CANL 0.719,1.135 1.156,1.302 0.438,0.167 10 false CANH 2.74,6.906 3.146,7.073 0.406,0.167 10 false CANL 4,6.917 4.438,7.083 0.438,0.167 10 false CANH 1.271,1.125 1.458,1.292 0.188,0.167 10 false 7 2.625,1.031 2.813,1.198 0.188,0.167 10 false 2 2.594,1.771 2.865,2.031 0.271,0.26 10 false 13 1.802,1.771 2.063,2.01 0.26,0.24 10 false W 1.771,0.958 2.063,1.125 0.292,0.167 10 false LG 4.135,6.094 4.427,6.271 0.292,0.177 10 false L 2.906,6.115 3.052,6.281 0.146,0.167 10 false W 1.25,1.688 1.438,1.854 0.188,0.167 10 false 8 3.99,6.656 4.177,6.823 0.188,0.167 10 false 13 2.969,6.656 3.156,6.823 0.188,0.167 10 false 26 0.104,1.979 0.365,2.281 0.26,0.302 10 false G6 3.354,7.521 3.865,7.708 0.51,0.188 10 false 120 Ω 4.917,7.229 5.302,7.427 0.385,0.198 10 false ECM 4.594,7.229 4.979,7.427 0.385,0.198 10 false A40 4.125,0.313 4.458,0.521 0.333,0.208 10 false SB 2.844,0.313 3.042,0.479 0.198,0.167 10 false W 2.76,0.698 3.01,0.948 0.25,0.25 10 false 15 4.229,0.698 4.396,0.906 0.167,0.208 10 false 4 3.052,0.813 3.365,1.031 0.313,0.219 10 false G71 3.813,0.802 4.125,1.021 0.313,0.219 10 false G71 2.542,1.219 2.854,1.438 0.313,0.219 10 false G71 2.542,1.583 2.854,1.802 0.313,0.219 10 false G71 4.323,1.865 4.635,2.083 0.313,0.219 10 false G71 4.323,2.229 4.635,2.448 0.313,0.219 10 false G71 4.333,3.729 4.646,3.948 0.313,0.219 10 false A51 4.333,4.094 4.646,4.313 0.313,0.219 10 false A51 3.073,5.51 3.385,5.729 0.313,0.219 10 false A51 3.833,5.51 4.146,5.729 0.313,0.219 10 false A51 4.208,5.521 4.396,5.688 0.188,0.167 10 false 9 2.792,5.521 3.063,5.75 0.271,0.229 10 false 20 2.521,4.635 2.833,4.854 0.313,0.219 10 false G71 2.521,5 2.833,5.219 0.313,0.219 10 false G71 1.802,3.531 1.958,3.698 0.156,0.167 10 false W 1.802,2.771 2.052,2.958 0.25,0.188 10 false BE 2.604,2.75 2.875,2.969 0.271,0.219 10 false 5 2.563,3.573 2.948,3.854 0.385,0.281 10 false 16 2.521,3 2.833,3.219 0.313,0.219 10 false G71 2.521,3.365 2.833,3.583 0.313,0.219 10 false G71 4.479,0.99 6.469,1.24 1.99,0.25 10 false CAN Junction Connector LH

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control main switch (ON/OFF switch), wait at least 60 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more.

·

After the repair, perform CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT IN CAN BUS LINES (COMBINATION METER ASSEMBLY - CAN J/C RH)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U159531E02
1.792,2.635 1.792,2.969 1.792,2.969 1.51,2.969 false 1.906,2.635 1.906,2.969 1.906,2.969 2.188,2.969 false 0.198,0.177 0.906,0.573 0.708,0.396 10 false *a 1.083,2.896 1.563,3.104 0.479,0.208 10 false CANH 2.271,2.885 2.719,3.083 0.448,0.198 10 false CANL 1.646,0.667 1.906,0.875 0.26,0.208 10 false G1

Disconnect the G1 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-31 (CANH) - G1-32 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)

HINT:

If the resistance becomes normal (between 108 to 132 Ω) when the connector is disconnected, there may be a short in the combination meter assembly.




OK

REPLACE COMBINATION METER ASSEMBLY

NG

2.CHECK FOR SHORT IN CAN BUS LINES (ECM - CAN J/C LH)
2.CHECK FOR SHORT IN CAN BUS LINES (ECM - CAN J/C LH)
a.

Reconnect the G1 combination meter assembly connector.


b.
U159410E02
2.573,1.615 2.854,1.615 2.854,1.615 2.854,2.396 false 2.573,1.542 2.573,0.948 2.573,0.948 2.729,0.948 false 0.146,0.083 0.385,0.323 0.24,0.24 10 false *a 2.802,0.875 3.24,1.073 0.438,0.198 10 false CANH 2.688,2.438 3.156,2.635 0.469,0.198 10 false CANL 1.771,0.719 2.052,0.896 0.281,0.177 10 false A40

Disconnect the A40 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-13 (CANH) - A40-26 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)

HINT:

If the resistance becomes normal (between 108 to 132 Ω) when the connector is disconnected, there may be a short in the ECM.




OK

NG

3.CHECK FOR SHORT IN CAN BUS LINES (CAN J/C RH)
3.CHECK FOR SHORT IN CAN BUS LINES (CAN J/C RH)
a.

Reconnect the A40 ECM connector.


b.
U183595E02
1.167,1.969 1.167,1.729 1.167,1.729 0.833,1.729 false 1.135,2.125 0.781,2.125 false 1.396,1.958 1.396,1.323 1.396,1.323 0.854,1.323 false 1.406,2.135 1.406,2.458 1.406,2.458 0.802,2.458 false 1.521,1.969 1.521,0.927 1.521,0.927 0.865,0.927 false 1.521,2.125 1.521,2.833 1.521,2.833 0.99,2.833 false 1.854,1.969 1.854,1.198 1.854,1.198 2.563,1.198 false 1.969,1.979 1.969,1.5 1.969,1.5 2.552,1.5 false 2.198,1.979 2.198,1.76 2.198,1.76 2.573,1.76 false 1.969,2.135 1.969,2.74 1.969,2.74 2.552,2.74 false 1.854,2.146 1.854,3.031 1.854,3.031 2.552,3.031 false 2.208,2.146 2.208,2.448 2.208,2.448 2.542,2.448 false 0.094,0 0.417,0.198 0.323,0.198 10 false *a 1.563,0.188 1.927,0.417 0.365,0.229 10 false G72 0.229,1.646 0.896,1.875 0.667,0.229 10 false CANH*b 0.25,1.229 0.917,1.458 0.667,0.229 10 false CANH*c 0.26,0.844 0.927,1.073 0.667,0.229 10 false CANH*d 2.594,1.104 3.26,1.333 0.667,0.229 10 false CANH*e 2.604,1.427 3.271,1.656 0.667,0.229 10 false CANH*f 2.615,1.677 3.229,1.906 0.615,0.229 10 false CANH*g 0.229,2.042 0.896,2.271 0.667,0.229 10 false CANL*b 0.24,2.354 0.906,2.583 0.667,0.229 10 false CANL*c 0.396,2.74 1.063,2.969 0.667,0.229 10 false CANL*d 2.594,2.938 3.167,3.167 0.573,0.229 10 false CANL*e 2.594,2.656 3.135,2.885 0.542,0.229 10 false CANL*f 2.594,2.354 3.167,2.583 0.573,0.229 10 false CANL*g

Disconnect the G72 CAN junction connector RH.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G72-1 (CANH) - G72-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Spiral cable with sensor sub-assembly (Steering sensor)
G72-3 (CANH) - G72-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Smart key ECU assembly (Certification ECU)
G72-4 (CANH) - G72-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Airbag sensor assembly
G72-7 (CANH) - G72-18 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Combination meter assembly
G72-8 (CANH) - G72-19 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Air conditioning amplifier assembly
G72-10 (CANH) - G72-21 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN junction connector LH


Text in Illustration
*a Front view of wire harness connector
(to CAN Junction Connector RH)
*b to Spiral Cable with Sensor Sub-assembly (Steering Sensor)
*c to Smart Key ECU Assembly (Certification ECU)
*d to Airbag Sensor Assembly
*e to Combination Meter Assembly
*f to Air Conditioning Amplifier Assembly
*g to CAN Junction Connector LH

Result:
Result Proceed to
OK A
NG (CAN junction connector LH main lines) B
NG (ECU or sensor branch lines) C
NG (Combination meter assembly main lines) D




A

REPLACE CAN JUNCTION CONNECTOR RH

B

4.CHECK FOR SHORT IN CAN BUS LINES (CAN J/C LH (INSTRUMENT PANEL WIRE SIDE))

C

6.CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR)

D

REPAIR OR REPLACE CAN MAIN BUS LINES (COMBINATION METER ASSEMBLY - CAN J/C RH)

4.CHECK FOR SHORT IN CAN BUS LINES (CAN J/C LH (INSTRUMENT PANEL WIRE SIDE))
a.
U183596E02
1.177,1.979 1.177,1.74 1.177,1.74 0.844,1.74 false 1.135,2.125 0.781,2.125 false 1.281,1.969 1.281,1.333 1.281,1.333 0.854,1.333 false 1.292,2.125 1.292,2.448 1.292,2.448 0.813,2.448 false 1.396,1.99 1.396,0.948 1.396,0.948 0.854,0.948 false 1.406,2.146 1.406,2.854 1.406,2.854 0.99,2.854 false 1.51,1.958 1.51,0.927 1.51,0.927 2.344,0.927 false 1.51,2.125 1.51,2.823 1.51,2.823 2.333,2.823 false 1.625,1.969 1.625,1.365 1.625,1.365 2.49,1.365 false 1.635,2.135 1.635,2.479 1.635,2.479 2.51,2.479 false 0.094,0.063 0.417,0.26 0.323,0.198 10 false *a 1.563,0.198 1.927,0.427 0.365,0.229 10 false G71 0.229,1.646 0.896,1.875 0.667,0.229 10 false CANH*b 0.26,1.24 0.927,1.469 0.667,0.229 10 false CANH*c 0.271,0.844 0.938,1.073 0.667,0.229 10 false CANH*d 2.385,0.844 3.052,1.073 0.667,0.229 10 false CANH*e 0.229,2.021 0.896,2.25 0.667,0.229 10 false CANL*b 0.271,2.354 0.938,2.583 0.667,0.229 10 false CANL*c 0.448,2.771 1.115,3 0.667,0.229 10 false CANL*d 2.375,2.74 2.948,2.969 0.573,0.229 10 false CANL*e 2.542,1.281 3.208,1.51 0.667,0.229 10 false CANH*f 2.552,2.396 3.125,2.625 0.573,0.229 10 false CANL*f

Disconnect the G71 CAN junction connector LH (instrument panel wire side).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G71-1 (CANH) - G71-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Main body ECU (Multiplex network body ECU)
G71-2 (CANH) - G71-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Power steering ECU assembly
G71-3 (CANH) - G71-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher DLC3
G71-4 (CANH) - G71-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher CAN junction connector RH
G71-5 (CANH) - G71-16 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Hybrid vehicle control computer assembly


Text in Illustration
*a Front view of wire harness connector
(to CAN Junction Connector LH (Instrument Panel Wire Side))
*b to Main Body ECU (Multiplex Network Body ECU)
*c to Power Steering ECU Assembly
*d to DLC3
*e to CAN Junction Connector RH
*f to Hybrid Vehicle Control Computer Assembly

Result:
Result Proceed to
OK A
NG (CAN junction connector RH main lines) B
NG (ECU or sensor branch lines) C
NG (DLC3 branch lines) D




A

5.CHECK FOR SHORT IN CAN BUS LINES (CAN J/C LH (ENGINE ROOM MAIN WIRE SIDE))

B

REPAIR OR REPLACE CAN MAIN BUS LINES (CAN J/C LH (INSTRUMENT PANEL WIRE SIDE) - CAN J/C RH)

C

6.CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR)

D

REPAIR OR REPLACE CAN BRANCH LINES CONNECTED TO DLC3

5.CHECK FOR SHORT IN CAN BUS LINES (CAN J/C LH (ENGINE ROOM MAIN WIRE SIDE))
a.
U159517E03
2.219,1.969 2.219,1.333 2.219,1.333 2.448,1.333 false 2.198,2.135 2.198,2.458 2.198,2.458 2.5,2.458 false 2.073,1.927 2.073,0.885 2.073,0.885 2.427,0.885 false 2.083,2.146 2.083,2.854 2.083,2.854 2.458,2.854 false 0.156,0.125 0.479,0.323 0.323,0.198 10 false *a 1.604,0.198 1.969,0.427 0.365,0.229 10 false A51 2.458,0.813 3.125,1.042 0.667,0.229 10 false CANH*b 2.479,1.25 3.146,1.479 0.667,0.229 10 false CANH*c 2.5,2.771 3.167,3 0.667,0.229 10 false CANL*b 2.563,2.375 3.229,2.604 0.667,0.229 10 false CANL*c

Disconnect the A51 CAN junction connector LH (engine room main wire side).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A51-9 (CANH) - A51-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω ECM
A51-10 (CANH) - A51-21 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Brake booster with master cylinder assembly (Skid control ECU)


Text in Illustration
*a Front view of wire harness connector
(to CAN Junction Connector LH (Engine Room Main Wire Side))
*b to ECM
*c to Brake Booster with Master Cylinder Assembly (Skid Control ECU)

Result:
Result Proceed to
OK A
NG (ECM main lines) B
NG (ECU or sensor branch lines) C




A

REPLACE CAN JUNCTION CONNECTOR LH

B

REPAIR OR REPLACE CAN MAIN BUS LINES (ECM - CAN J/C LH (ENGINE ROOM MAIN WIRE SIDE))

C

6.CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR)
6.CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR)
a.

Reconnect all wire harness connectors (CAN junction connector LH and CAN junction connector RH).


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU).


c.
U159345E01
0.087,0.032 0.927,0.365 0.840,0.334 10 *1 1.622,0.756 1.930,0.938 0.309,0.181 10 G4 2.452,1.066 2.863,1.247 0.411,0.181 10 CANH 2.435,2.911 2.823,3.092 0.387,0.181 10 CANL 2.078,1.828 2.441,1.27 false 2.085,2.535 2.419,2.868 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G4-6 (CANH) - G4-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*1 DLC3

HINT:

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.




OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH LINES OR CONNECTOR