Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2014.12–2015.11
RM2170E _57 Power Source / Network _057033 NETWORKING _0278068 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check CAN Bus Lines for Short Circuit (RHD Models)  


DESCRIPTION

There may be a short circuit between the V bus main lines and/or CAN branch lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.

Symptom Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.
·

Short in CAN main bus lines

·

Short in CAN branch lines

·

ECM

·

Brake booster with master cylinder assembly (Skid control ECU)

·

Main body ECU (Multiplex network body ECU)

·

Air conditioning amplifier assembly

·

Power steering ECU assembly

·

Smart key ECU assembly (Certification ECU)

·

Airbag sensor assembly

·

Spiral cable with sensor sub-assembly (Steering sensor)

·

Hybrid vehicle control computer assembly

·

Combination meter assembly

·

CAN junction connector LH

·

CAN junction connector RH



WIRING DIAGRAM

C260982E07
3.979,7.979 5.708,8.167 1.729,0.188 10 false : CAN Branch Line (CANH) 3.979,8.385 5.708,8.573 1.729,0.188 10 false : CAN Branch Line (CANL) 0.854,7.99 2.771,8.177 1.917,0.188 10 false : CAN Main Bus Line (CANH) 0.854,8.406 2.771,8.594 1.917,0.188 10 false : CAN Main Bus Line (CANL) 3.448,0.219 3.865,0.406 0.417,0.188 10 false 120 Ω 2.781,0.927 3.188,1.094 0.406,0.167 10 false CANL 0.417,0.448 0.781,0.615 0.365,0.167 10 false G1 4.115,1.438 4.333,1.656 0.219,0.219 10 false G 3.021,1.438 3.219,1.604 0.198,0.167 10 false W 0.667,0.448 2.521,0.646 1.854,0.198 10 false Combination Meter Assembly 0.125,0.063 1.979,0.26 1.854,0.198 12 false V Bus: 4.115,0.927 4.552,1.094 0.438,0.167 10 false CANH 4.083,1.229 4.427,1.448 0.344,0.219 10 false 31 3.01,1.24 3.323,1.448 0.313,0.208 10 false 32 5.188,0.563 6.396,0.75 1.208,0.188 10 false x: Suspected Area 4.865,2.125 6.854,2.375 1.99,0.25 10 false CAN Junction Connector RH 1.021,6.042 1.427,6.208 0.406,0.167 10 false CANL 1.01,5.469 1.448,5.635 0.438,0.167 10 false CANH 1.563,5.469 1.792,5.635 0.229,0.167 10 false 11 2.146,5.417 2.26,5.583 0.115,0.167 10 false V 2.125,6.125 2.292,6.292 0.167,0.167 10 false W 1.563,6.052 1.813,6.271 0.25,0.219 10 false 12 2.781,5.458 3.042,5.719 0.26,0.26 10 false 8 2.729,6.083 2.979,6.354 0.25,0.271 10 false 19 2.74,3.719 2.938,3.948 0.198,0.229 10 false 4 2.698,4.448 2.927,4.656 0.229,0.208 10 false 15 0.063,6.365 0.354,6.542 0.292,0.177 10 false G34 0.385,6.365 1.969,6.74 1.583,0.375 10 false Air Conditioning Amplifier Assembly 0.51,4.698 2.083,5.052 1.573,0.354 10 false Airbag Sensor Assembly 1.073,4.406 1.479,4.573 0.406,0.167 10 false CANL 1.052,3.854 1.49,4.021 0.438,0.167 10 false CANH 2.156,3.719 2.354,3.969 0.198,0.25 10 false B 2.135,4.49 2.333,4.688 0.198,0.198 10 false W 0.177,4.698 0.479,4.875 0.302,0.177 10 false G18 1.583,3.792 1.875,4.021 0.292,0.229 10 false 13 1.594,4.417 1.781,4.583 0.188,0.167 10 false 22 4.552,2.125 4.917,2.406 0.365,0.281 10 false G72 3.021,1.677 3.313,1.917 0.292,0.24 10 false 18 4.135,1.677 4.406,1.875 0.271,0.198 10 false 7 3.031,7.229 3.333,7.5 0.302,0.271 10 false 21 4.104,7.229 4.49,7.531 0.385,0.302 10 false 10 2.75,2.021 2.958,2.188 0.208,0.167 10 false 1 2.698,2.688 2.948,2.927 0.25,0.24 10 false 12 1.042,2.667 1.448,2.833 0.406,0.167 10 false CANL 2.125,2.76 2.281,2.927 0.156,0.167 10 false W 0.094,2.979 0.458,3.146 0.365,0.167 10 false G30 1.031,2.115 1.469,2.281 0.438,0.167 10 false CANH 1.563,2.125 1.781,2.323 0.219,0.198 10 false 4 1.563,2.677 1.802,2.885 0.24,0.208 10 false 3 2.167,1.969 2.344,2.115 0.177,0.146 10 false P 0.427,2.979 2.594,3.427 2.167,0.448 10 false Spiral Cable with Sensor Sub-assembly (Steering Sensor) 5.031,5.313 5.219,5.573 0.188,0.26 10 false W 6.073,5.073 6.479,5.24 0.406,0.167 10 false CANL 5.917,4.74 6.354,4.906 0.438,0.167 10 false CANH 4.448,4.563 4.719,4.781 0.271,0.219 10 false 11 4.448,5.292 4.833,5.573 0.385,0.281 10 false 22 5.813,5.281 6.01,5.448 0.198,0.167 10 false 14 5.625,4.615 5.802,4.781 0.177,0.167 10 false 6 6.135,5.354 6.458,5.542 0.323,0.188 10 false G4 6.406,5.354 6.802,5.542 0.396,0.188 10 false DLC3 5,4.563 5.365,4.823 0.365,0.26 10 false GR 5.802,3.76 7.135,4.125 1.333,0.365 10 false Power Steering ECU Assembly 5.948,3.49 6.354,3.656 0.406,0.167 10 false CANL 5.948,2.833 6.385,3 0.438,0.167 10 false CANH 5.719,2.802 5.906,2.969 0.188,0.167 10 false 7 4.469,2.823 4.656,2.99 0.188,0.167 10 false 6 4.427,3.531 4.698,3.792 0.271,0.26 10 false 17 5.01,3.563 5.271,3.802 0.26,0.24 10 false W 4.99,2.76 5.281,2.927 0.292,0.167 10 false LG 5.719,3.469 5.906,3.635 0.188,0.167 10 false 8 5.563,3.76 5.823,4.063 0.26,0.302 10 false G6

C251631E10
3.948,8.073 6.073,8.292 2.125,0.219 10 false : CAN Branch Line (CANH) 3.969,8.479 5.75,8.708 1.781,0.229 10 false : CAN Branch Line (CANL) 0.854,8.052 2.885,8.281 2.031,0.229 10 false : CAN Main Bus Line (CANH) 0.854,8.448 2.833,8.719 1.979,0.271 10 false : CAN Main Bus Line (CANL) 0.344,3.063 2.021,3.396 1.677,0.333 10 false Smart Key ECU Assembly (Certification ECU) 0.573,1.063 2.375,1.677 1.802,0.615 10 false CAN Junction Connector LH 0.073,3.063 0.719,3.5 0.646,0.438 10 false G79 0.365,5.115 1.823,5.521 1.458,0.406 10 false Hybrid Vehicle Control Computer Assembly 0.083,5.115 0.583,5.583 0.5,0.469 10 false G81 1.271,4.198 1.667,4.667 0.396,0.469 10 false 25 1.271,4.854 1.667,5.344 0.396,0.49 10 false 24 5.917,2.198 7.094,2.854 1.177,0.656 10 false Main Body ECU (Multiplex Network Body ECU) 5.583,2.208 6.031,2.573 0.448,0.365 10 false G59 5.938,4.115 7.156,5.25 1.219,1.135 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 5.604,4.135 6.188,4.573 0.583,0.438 10 false A41 4.458,7.219 4.99,7.823 0.531,0.604 10 false ECM 4.167,7.208 4.438,7.458 0.271,0.25 10 false A40 2.354,6.906 3.083,7.323 0.729,0.417 10 false CANL 0.792,4.854 1.552,5.26 0.76,0.406 10 false CA1L 0.792,4.219 1.406,4.625 0.615,0.406 10 false CA1H 1.271,2.198 1.688,2.583 0.417,0.385 10 false 14 4.063,1.188 4.448,1.469 0.385,0.281 10 false 1 1.271,2.792 1.771,3.167 0.5,0.375 10 false 15 0.813,2.792 1.396,3.104 0.583,0.313 10 false CANL 0.813,2.198 1.448,2.573 0.635,0.375 10 false CANH 2.688,0.823 3.146,1.156 0.458,0.333 10 false G71 2.156,2.302 2.656,2.635 0.5,0.333 10 false G71 2.167,2.667 2.688,3.01 0.521,0.344 10 false G71 2.167,4.333 2.656,4.656 0.49,0.323 10 false G71 2.177,4.698 2.667,5.063 0.49,0.365 10 false G71 2.688,5.51 3.313,5.99 0.625,0.479 10 false A51 3.469,5.51 3.979,5.958 0.51,0.448 10 false A51 3.979,3.313 4.51,3.625 0.531,0.313 10 false A51 3.969,3.677 4.51,3.99 0.542,0.313 10 false A51 3.438,0.823 3.813,1.177 0.375,0.354 10 false G71 3.958,1.417 4.427,1.677 0.469,0.26 10 false G71 3.958,1.771 4.396,2.042 0.438,0.271 10 false G71 5.729,1.281 6.073,1.583 0.344,0.302 10 false 14 4.021,2.01 4.458,2.354 0.438,0.344 10 false 12 3.979,3.135 4.448,3.427 0.469,0.292 10 false 10 4,3.875 4.406,4.188 0.406,0.313 10 false 21 2.292,2.104 2.656,2.448 0.365,0.344 10 false 3 3.833,0.813 4.25,1.104 0.417,0.292 10 false 4 2.438,0.802 2.875,1.188 0.438,0.385 10 false 15 2.229,2.885 2.49,3.063 0.26,0.177 10 false 14 2.26,4.125 2.708,4.438 0.448,0.313 10 false 5 2.229,4.917 2.76,5.271 0.531,0.354 10 false 16 5.75,1.896 6.01,2.073 0.26,0.177 10 false 13 5.99,1.885 6.635,2.198 0.646,0.313 10 false CANL 5.99,1.302 6.594,1.677 0.604,0.375 10 false CANH 5.688,3.229 6.177,3.656 0.49,0.427 10 false 37 5.688,3.771 6.115,4.146 0.427,0.375 10 false 38 5.979,3.781 6.719,4.219 0.74,0.438 10 false CA1L 5.958,3.219 6.688,3.708 0.729,0.49 10 false CA1H 2.469,6.635 2.938,7.052 0.469,0.417 10 false 26 2.448,5.521 2.969,5.896 0.521,0.375 10 false 20 3.698,6.906 4.344,7.292 0.646,0.385 10 false CANH 3.667,6.646 4.146,6.969 0.479,0.323 10 false 13 3.813,5.51 4.229,5.865 0.417,0.354 10 false 9 3.042,7.531 3.938,8 0.896,0.469 10 false 120Ω 5.125,0.292 6.51,0.708 1.385,0.417 10 false x:Suspected Area 4.969,3.865 5.375,4.167 0.406,0.302 10 false W 4.99,3.125 5.323,3.458 0.333,0.333 10 false B 2.542,6.229 3.104,6.625 0.563,0.396 10 false W 3.708,6.24 4.156,6.583 0.448,0.344 10 false L 1.625,2.865 2.021,3.25 0.396,0.385 10 false W 1.635,2.104 1.969,2.521 0.333,0.417 10 false L 5.031,1.979 5.427,2.313 0.396,0.333 10 false W 5.031,1.198 5.344,1.5 0.313,0.302 10 false R 2.594,0.396 2.99,0.656 0.396,0.26 10 false W 3.698,0.406 4.104,0.698 0.406,0.292 10 false SB 1.646,4.896 2.146,5.375 0.5,0.479 10 false W 1.625,4.135 1.99,4.5 0.365,0.365 10 false BE

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control main switch (ON/OFF switch), wait at least 60 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more.

·

After the repair, perform CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT IN CAN BUS LINES (COMBINATION METER ASSEMBLY - CAN J/C RH)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U159531E02
1.792,2.635 1.792,2.969 1.792,2.969 1.51,2.969 false 1.906,2.635 1.906,2.969 1.906,2.969 2.188,2.969 false 0.198,0.177 0.906,0.573 0.708,0.396 10 false *a 1.083,2.896 1.563,3.104 0.479,0.208 10 false CANH 2.271,2.885 2.719,3.083 0.448,0.198 10 false CANL 1.646,0.667 1.906,0.875 0.26,0.208 10 false G1

Disconnect the G1 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-31 (CANH) - G1-32 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)

HINT:

If the resistance becomes normal (between 108 to 132 Ω) when the connector is disconnected, there may be a short in the combination meter assembly.




OK

REPLACE COMBINATION METER ASSEMBLY

NG

2.CHECK FOR SHORT IN CAN BUS LINES (ECM MAIN BUS LINE - CAN J/C LH)
2.CHECK FOR SHORT IN CAN BUS LINES (ECM MAIN BUS LINE - CAN J/C LH)
a.

Reconnect the G1 combination meter assembly connector.


b.
U159410E02
2.573,1.615 2.854,1.615 2.854,1.615 2.854,2.396 false 2.573,1.542 2.573,0.948 2.573,0.948 2.729,0.948 false 0.146,0.083 0.385,0.323 0.24,0.24 10 false *a 2.802,0.875 3.24,1.073 0.438,0.198 10 false CANH 2.688,2.438 3.156,2.635 0.469,0.198 10 false CANL 1.771,0.719 2.052,0.896 0.281,0.177 10 false A40

Disconnect the A40 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-13 (CANH) - A40-26 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)

HINT:

If the resistance becomes normal (between 108 to 132 Ω) when the connector is disconnected, there may be a short in the ECM.




OK

NG

3.CHECK FOR SHORT IN CAN BUS LINES (CAN J/C RH)
3.CHECK FOR SHORT IN CAN BUS LINES (CAN J/C RH)
a.

Reconnect the A40 ECM connector.


b.
U183597E02
1.167,1.979 1.167,1.74 1.167,1.74 0.833,1.74 false 1.146,2.115 0.792,2.115 false 1.51,1.958 1.51,1.323 1.51,1.323 0.844,1.323 false 1.521,2.135 1.521,2.458 1.521,2.458 0.802,2.458 false 1.74,1.958 1.74,0.917 1.74,0.917 0.854,0.917 false 1.74,2.125 1.74,2.833 1.74,2.833 0.979,2.833 false 1.844,1.969 1.844,0.938 1.844,0.938 2.552,0.938 false 1.969,1.969 1.969,1.229 1.969,1.229 2.552,1.229 false 2.198,1.979 2.198,1.5 2.198,1.5 2.573,1.5 false 1.969,2.146 1.969,3.042 1.969,3.042 2.552,3.042 false 1.865,2.135 1.865,3.094 1.865,3.094 1.167,3.094 false 2.198,2.125 2.198,2.719 2.198,2.719 2.531,2.719 false 2.313,1.979 2.313,1.844 2.313,1.844 2.563,1.844 false 2.313,2.135 2.313,2.427 2.313,2.427 2.563,2.427 false 0.094,0 0.417,0.198 0.323,0.198 10 false *a 1.563,0.198 1.927,0.427 0.365,0.229 10 false G72 0.26,1.646 0.927,1.875 0.667,0.229 10 false CANH*b 0.26,1.219 0.927,1.448 0.667,0.229 10 false CANH*c 0.271,0.823 0.938,1.052 0.667,0.229 10 false CANH*d 2.594,0.854 3.26,1.083 0.667,0.229 10 false CANH*e 2.594,1.156 3.26,1.385 0.667,0.229 10 false CANH*f 2.604,1.427 3.219,1.656 0.615,0.229 10 false CANH*g 0.24,2.021 0.906,2.25 0.667,0.229 10 false CANL*b 0.24,2.354 0.906,2.583 0.667,0.229 10 false CANL*c 0.417,2.729 1.083,2.958 0.667,0.229 10 false CANL*d 0.594,3 1.167,3.229 0.573,0.229 10 false CANL*e 2.594,3 3.135,3.229 0.542,0.229 10 false CANL*f 2.594,2.635 3.167,2.865 0.573,0.229 10 false CANL*g 2.604,1.76 3.219,1.99 0.615,0.229 10 false CANH*h 2.615,2.344 3.188,2.573 0.573,0.229 10 false CANL*h

Disconnect the G72 CAN junction connector RH.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G72-1 (CANH) - G72-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Spiral cable with sensor sub-assembly (Steering sensor)
G72-4 (CANH) - G72-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Airbag sensor assembly
G72-6 (CANH) - G72-17 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Power steering ECU assembly
G72-7 (CANH) - G72-18 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Combination meter assembly
G72-8 (CANH) - G72-19 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Air conditioning amplifier assembly
G72-10 (CANH) - G72-21 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN junction connector LH
G72-11 (CANH) - G72-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher DLC3


Text in Illustration
*a Front view of wire harness connector
(to CAN Junction Connector RH)
*b to Spiral Cable with Sensor Sub-assembly (Steering Sensor)
*c to Airbag Sensor Assembly
*d to Power Steering ECU Assembly
*e to Combination Meter Assembly
*f to Air Conditioning Amplifier Assembly
*g to CAN Junction Connector LH
*h to DLC3

Result:
Result Proceed to
OK A
NG (CAN junction connector LH main lines) B
NG (ECU or sensor branch lines) C
NG (Combination meter assembly main lines) D
NG (DLC3 branch lines) E




A

REPLACE CAN JUNCTION CONNECTOR RH

B

4.CHECK FOR SHORT IN CAN BUS LINES (CAN J/C LH (INSTRUMENT PANEL WIRE SIDE))

C

6.CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR)

D

REPAIR OR REPLACE CAN MAIN BUS LINES (COMBINATION METER ASSEMBLY - CAN J/C RH)

E

REPAIR OR REPLACE CAN BRANCH LINES CONNECTED TO DLC3

4.CHECK FOR SHORT IN CAN BUS LINES (CAN J/C LH (INSTRUMENT PANEL WIRE SIDE))
a.
U183598E02
1.167,1.948 1.167,1.708 1.167,1.708 0.833,1.708 false 1.135,2.115 0.781,2.115 false 1.385,1.948 1.385,1.313 1.385,1.313 0.844,1.313 false 1.406,2.135 1.406,2.458 1.406,2.458 0.802,2.458 false 1.51,1.948 1.51,0.906 1.51,0.906 0.854,0.906 false 1.521,2.125 1.521,2.833 1.521,2.833 0.99,2.833 false 1.625,1.969 1.625,0.938 1.625,0.938 2.333,0.938 false 1.635,2.135 1.635,2.833 1.635,2.833 2.333,2.833 false 0.094,0 0.417,0.198 0.323,0.198 10 false *a 1.573,0.188 1.938,0.417 0.365,0.229 10 false G71 0.229,1.604 0.896,1.833 0.667,0.229 10 false CANH*b 0.229,1.198 0.896,1.427 0.667,0.229 10 false CANH*c 0.24,0.802 0.906,1.031 0.667,0.229 10 false CANH*d 2.365,0.833 3.031,1.063 0.667,0.229 10 false CANH*e 0.219,2.01 0.885,2.24 0.667,0.229 10 false CANL*b 0.26,2.365 0.927,2.594 0.667,0.229 10 false CANL*c 0.427,2.75 1.094,2.979 0.667,0.229 10 false CANL*d 2.375,2.75 2.948,2.979 0.573,0.229 10 false CANL*e

Disconnect the G71 CAN junction connector LH (instrument panel wire side).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G71-1 (CANH) - G71-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Main body ECU (Multiplex network body ECU)
G71-3 (CANH) - G71-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Smart key ECU assembly (Certification ECU)
G71-4 (CANH) - G71-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher CAN junction connector RH
G71-5 (CANH) - G71-16 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Hybrid vehicle control computer assembly


Text in Illustration
*a Front view of wire harness connector
(to CAN Junction Connector LH (Instrument Panel Wire Side))
*b to Main Body ECU (Multiplex Network Body ECU)
*c to Smart Key ECU Assembly (Certification ECU)
*d to CAN Junction Connector RH
*e to Hybrid Vehicle Control Computer Assembly

Result:
Result Proceed to
OK A
NG (CAN junction connector RH main lines) B
NG (ECU or sensor branch lines) C




A

5.CHECK FOR SHORT IN CAN BUS LINES (CAN J/C LH (ENGINE ROOM MAIN WIRE SIDE))

B

REPAIR OR REPLACE CAN MAIN BUS LINES (CAN J/C LH (INSTRUMENT PANEL WIRE SIDE) - CAN J/C RH)

C

6.CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR)
5.CHECK FOR SHORT IN CAN BUS LINES (CAN J/C LH (ENGINE ROOM MAIN WIRE SIDE))
a.
U159517E03
2.219,1.969 2.219,1.333 2.219,1.333 2.448,1.333 false 2.198,2.135 2.198,2.458 2.198,2.458 2.5,2.458 false 2.073,1.927 2.073,0.885 2.073,0.885 2.427,0.885 false 2.083,2.146 2.083,2.854 2.083,2.854 2.458,2.854 false 0.156,0.125 0.479,0.323 0.323,0.198 10 false *a 1.604,0.198 1.969,0.427 0.365,0.229 10 false A51 2.458,0.813 3.125,1.042 0.667,0.229 10 false CANH*b 2.479,1.25 3.146,1.479 0.667,0.229 10 false CANH*c 2.5,2.771 3.167,3 0.667,0.229 10 false CANL*b 2.563,2.375 3.229,2.604 0.667,0.229 10 false CANL*c

Disconnect the A51 CAN junction connector LH (engine room main wire side).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A51-9 (CANH) - A51-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω ECM
A51-10 (CANH) - A51-21 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Brake booster with master cylinder assembly (Skid control ECU)


Text in Illustration
*a Front view of wire harness connector
(to CAN Junction Connector LH (Engine Room Main Wire Side))
*b to ECM
*c to Brake Booster with Master Cylinder Assembly (Skid Control ECU)

Result:
Result Proceed to
OK A
NG (ECM main lines) B
NG (ECU or sensor branch lines) C




A

REPLACE CAN JUNCTION CONNECTOR LH

B

REPAIR OR REPLACE CAN MAIN BUS LINES (ECM - CAN J/C LH (ENGINE ROOM MAIN WIRE SIDE))

C

6.CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR)
6.CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR)
a.

Reconnect all wire harness connectors (CAN junction connector LH and CAN junction connector RH).


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU).


c.
U159345E01
0.087,0.032 0.927,0.365 0.840,0.334 10 *1 1.622,0.756 1.930,0.938 0.309,0.181 10 G4 2.452,1.066 2.863,1.247 0.411,0.181 10 CANH 2.435,2.911 2.823,3.092 0.387,0.181 10 CANL 2.078,1.828 2.441,1.27 false 2.085,2.535 2.419,2.868 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G4-6 (CANH) - G4-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*1 DLC3

HINT:

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.




OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH LINES OR CONNECTOR