Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2014.12–2015.11
RM2170E _57 Power Source / Network _057033 NETWORKING _0278068 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check CAN Bus Line for Short to +B (RHD Models)  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and +B when no resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of the DLC3.

Symptom Trouble Area
No resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of the DLC3.
·

Short to +B in CAN main bus line

·

Short to +B in CAN branch line

·

ECM

·

Brake booster with master cylinder assembly (Skid control ECU)

·

Main body ECU (Multiplex network body ECU)

·

Air conditioning amplifier assembly

·

Power steering ECU assembly

·

Smart key ECU assembly (Certification ECU)

·

Airbag sensor assembly

·

Spiral cable with sensor sub-assembly (Steering sensor)

·

Hybrid vehicle control computer assembly

·

Combination meter assembly

·

CAN junction connector LH

·

CAN junction connector RH



WIRING DIAGRAM

C260982E04
3.982,7.978 5.713,8.165 1.732,0.187 10 : CAN Branch Line (CANH) 3.978,8.386 5.709,8.573 1.732,0.187 10 : CAN Branch Line (CANL) 0.851,7.994 2.766,8.181 1.914,0.187 10 : CAN Main Bus Line (CANH) 0.851,8.404 2.766,8.591 1.914,0.187 10 : CAN Main Bus Line (CANL) 3.451,0.222 3.867,0.406 0.416,0.184 10 120 Ω 2.781,0.925 3.192,1.088 0.411,0.163 10 CANL 0.418,0.45 0.780,0.613 0.362,0.163 10 G1 4.169,1.414 4.383,1.635 0.214,0.221 10 G 2.984,1.414 3.177,1.577 0.193,0.163 10 W 0.665,0.45 2.519,0.650 1.855,0.200 10 Combination Meter Assembly 0.12,0.062 1.975,0.262 1.855,0.200 12 V Bus: 4.119,0.925 4.553,1.088 0.434,0.163 10 CANH 4.111,1.184 4.450,1.405 0.339,0.221 10 31 3.007,1.184 3.319,1.388 0.312,0.204 10 32 5.19,0.563 6.400,0.749 1.210,0.185 10 x: Suspected Area 4.864,2.123 6.856,2.376 1.992,0.253 10 CAN Junction Connector RH 1.016,6.044 1.427,6.207 0.411,0.163 10 CANL 1.011,5.472 1.445,5.635 0.434,0.163 10 CANH 1.564,5.471 1.795,5.634 0.231,0.163 10 11 2.17,5.381 2.288,5.544 0.118,0.163 10 V 2.121,6.124 2.283,6.287 0.162,0.163 10 W 1.565,6.049 1.812,6.267 0.247,0.217 10 12 2.779,5.461 3.039,5.719 0.261,0.259 10 8 2.732,6.08 2.983,6.356 0.251,0.276 10 19 2.739,3.719 2.936,3.947 0.197,0.229 10 4 2.697,4.448 2.931,4.657 0.234,0.208 10 15 0.066,6.363 0.360,6.535 0.295,0.172 10 G34 0.381,6.363 1.967,6.742 1.586,0.379 10 Air Conditioning Amplifier Assembly 0.511,4.698 2.084,5.048 1.574,0.350 10 Airbag Sensor Assembly 1.075,4.407 1.486,4.570 0.411,0.163 10 CANL 1.052,3.783 1.486,3.945 0.434,0.163 10 CANH 2.16,3.722 2.361,3.967 0.201,0.245 10 B 2.134,4.487 2.337,4.680 0.203,0.194 10 W 0.173,4.698 0.470,4.877 0.297,0.179 10 G18 1.575,3.79 1.865,4.020 0.289,0.230 10 13 1.589,4.414 1.777,4.577 0.188,0.163 10 22 4.549,2.123 4.918,2.404 0.369,0.281 10 G72 2.983,1.682 3.273,1.921 0.290,0.240 10 18 4.137,1.682 4.412,1.884 0.275,0.203 10 7 3.032,7.178 3.330,7.446 0.298,0.268 10 21 4.101,7.178 4.490,7.479 0.389,0.301 10 10 2.745,2.025 2.951,2.188 0.206,0.163 10 1 2.7,2.691 2.952,2.930 0.251,0.239 10 12 1.037,2.668 1.448,2.831 0.411,0.163 10 CANL 2.136,2.747 2.298,2.910 0.161,0.163 10 W 0.092,2.979 0.454,3.141 0.362,0.163 10 G30 1.028,2.055 1.462,2.218 0.434,0.163 10 CANH 1.564,2.057 1.785,2.251 0.221,0.194 10 4 1.564,2.681 1.806,2.892 0.242,0.211 10 3 2.164,1.97 2.345,2.119 0.181,0.149 10 P 0.424,2.979 2.592,3.432 2.168,0.453 10 Spiral Cable with Sensor Sub-assembly (Steering Sensor) 5.032,5.312 5.224,5.573 0.192,0.261 10 W 6.071,5.078 6.482,5.241 0.411,0.163 10 CANL 5.918,4.736 6.352,4.899 0.434,0.163 10 CANH 4.443,4.56 4.718,4.778 0.275,0.217 10 11 4.443,5.288 4.832,5.572 0.389,0.284 10 22 5.812,5.282 6.012,5.444 0.200,0.163 10 14 5.625,4.613 5.802,4.775 0.178,0.163 10 6 6.138,5.355 6.460,5.540 0.322,0.185 10 G4 6.404,5.355 6.798,5.540 0.394,0.185 10 DLC3 5.001,4.56 5.364,4.819 0.363,0.259 10 GR 5.807,3.765 7.142,4.133 1.336,0.368 10 Power Steering ECU Assembly 5.943,3.486 6.354,3.649 0.411,0.163 10 CANL 5.943,2.837 6.378,3.000 0.434,0.163 10 CANH 5.715,2.805 5.903,2.968 0.188,0.163 10 7 4.469,2.818 4.658,2.980 0.188,0.163 10 6 4.43,3.533 4.698,3.795 0.268,0.262 10 17 5.012,3.565 5.269,3.808 0.257,0.243 10 W 4.985,2.761 5.277,2.923 0.292,0.163 10 LG 5.715,3.471 5.903,3.634 0.188,0.163 10 8 5.56,3.765 5.819,4.067 0.259,0.302 10 G6

C251631E10
3.948,8.073 6.073,8.292 2.125,0.219 10 false : CAN Branch Line (CANH) 3.969,8.479 5.75,8.708 1.781,0.229 10 false : CAN Branch Line (CANL) 0.854,8.052 2.885,8.281 2.031,0.229 10 false : CAN Main Bus Line (CANH) 0.854,8.448 2.833,8.719 1.979,0.271 10 false : CAN Main Bus Line (CANL) 0.344,3.063 2.021,3.396 1.677,0.333 10 false Smart Key ECU Assembly (Certification ECU) 0.573,1.063 2.375,1.677 1.802,0.615 10 false CAN Junction Connector LH 0.073,3.063 0.719,3.5 0.646,0.438 10 false G79 0.365,5.115 1.823,5.521 1.458,0.406 10 false Hybrid Vehicle Control Computer Assembly 0.083,5.115 0.583,5.583 0.5,0.469 10 false G81 1.271,4.198 1.667,4.667 0.396,0.469 10 false 25 1.271,4.854 1.667,5.344 0.396,0.49 10 false 24 5.917,2.198 7.094,2.854 1.177,0.656 10 false Main Body ECU (Multiplex Network Body ECU) 5.583,2.208 6.031,2.573 0.448,0.365 10 false G59 5.938,4.115 7.156,5.25 1.219,1.135 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 5.604,4.135 6.188,4.573 0.583,0.438 10 false A41 4.458,7.219 4.99,7.823 0.531,0.604 10 false ECM 4.167,7.208 4.438,7.458 0.271,0.25 10 false A40 2.354,6.906 3.083,7.323 0.729,0.417 10 false CANL 0.792,4.854 1.552,5.26 0.76,0.406 10 false CA1L 0.792,4.219 1.406,4.625 0.615,0.406 10 false CA1H 1.271,2.198 1.688,2.583 0.417,0.385 10 false 14 4.063,1.188 4.448,1.469 0.385,0.281 10 false 1 1.271,2.792 1.771,3.167 0.5,0.375 10 false 15 0.813,2.792 1.396,3.104 0.583,0.313 10 false CANL 0.813,2.198 1.448,2.573 0.635,0.375 10 false CANH 2.688,0.823 3.146,1.156 0.458,0.333 10 false G71 2.156,2.302 2.656,2.635 0.5,0.333 10 false G71 2.167,2.667 2.688,3.01 0.521,0.344 10 false G71 2.167,4.333 2.656,4.656 0.49,0.323 10 false G71 2.177,4.698 2.667,5.063 0.49,0.365 10 false G71 2.688,5.51 3.313,5.99 0.625,0.479 10 false A51 3.469,5.51 3.979,5.958 0.51,0.448 10 false A51 3.979,3.313 4.51,3.625 0.531,0.313 10 false A51 3.969,3.677 4.51,3.99 0.542,0.313 10 false A51 3.438,0.823 3.813,1.177 0.375,0.354 10 false G71 3.958,1.417 4.427,1.677 0.469,0.26 10 false G71 3.958,1.771 4.396,2.042 0.438,0.271 10 false G71 5.729,1.281 6.073,1.583 0.344,0.302 10 false 14 4.021,2.01 4.458,2.354 0.438,0.344 10 false 12 3.979,3.135 4.448,3.427 0.469,0.292 10 false 10 4,3.875 4.406,4.188 0.406,0.313 10 false 21 2.292,2.104 2.656,2.448 0.365,0.344 10 false 3 3.833,0.813 4.25,1.104 0.417,0.292 10 false 4 2.438,0.802 2.875,1.188 0.438,0.385 10 false 15 2.229,2.885 2.49,3.063 0.26,0.177 10 false 14 2.26,4.125 2.708,4.438 0.448,0.313 10 false 5 2.229,4.917 2.76,5.271 0.531,0.354 10 false 16 5.75,1.896 6.01,2.073 0.26,0.177 10 false 13 5.99,1.885 6.635,2.198 0.646,0.313 10 false CANL 5.99,1.302 6.594,1.677 0.604,0.375 10 false CANH 5.688,3.229 6.177,3.656 0.49,0.427 10 false 37 5.688,3.771 6.115,4.146 0.427,0.375 10 false 38 5.979,3.781 6.719,4.219 0.74,0.438 10 false CA1L 5.958,3.219 6.688,3.708 0.729,0.49 10 false CA1H 2.469,6.635 2.938,7.052 0.469,0.417 10 false 26 2.448,5.521 2.969,5.896 0.521,0.375 10 false 20 3.698,6.906 4.344,7.292 0.646,0.385 10 false CANH 3.667,6.646 4.146,6.969 0.479,0.323 10 false 13 3.813,5.51 4.229,5.865 0.417,0.354 10 false 9 3.042,7.531 3.938,8 0.896,0.469 10 false 120Ω 5.125,0.292 6.51,0.708 1.385,0.417 10 false x:Suspected Area 4.969,3.865 5.375,4.167 0.406,0.302 10 false W 4.99,3.125 5.323,3.458 0.333,0.333 10 false B 2.542,6.229 3.104,6.625 0.563,0.396 10 false W 3.708,6.24 4.156,6.583 0.448,0.344 10 false L 1.625,2.865 2.021,3.25 0.396,0.385 10 false W 1.635,2.104 1.969,2.521 0.333,0.417 10 false L 5.031,1.979 5.427,2.313 0.396,0.333 10 false W 5.031,1.198 5.344,1.5 0.313,0.302 10 false R 2.594,0.396 2.99,0.656 0.396,0.26 10 false W 3.698,0.406 4.104,0.698 0.406,0.292 10 false SB 1.646,4.896 2.146,5.375 0.5,0.479 10 false W 1.625,4.135 1.99,4.5 0.365,0.365 10 false BE

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control main switch (ON/OFF switch), wait at least 60 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more.

·

After the repair, perform CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN J/C RH)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U183622E02
2.51,3.729 2.51,4.063 false 1.198,1.542 1.198,1.427 1.198,1.427 0.802,1.427 false 1.177,1.698 0.833,1.698 false 1.552,1.563 1.552,1.188 1.552,1.188 0.833,1.188 false 1.875,1.552 1.875,0.625 1.875,0.625 2.542,0.625 false 2,1.542 2,0.885 2,0.885 2.542,0.885 false 2.229,1.542 2.229,1.125 2.229,1.125 2.542,1.125 false 1.542,1.75 1.542,2 1.542,2 0.844,2 false 1.896,1.729 1.896,2.583 1.896,2.583 2.573,2.583 false 2,1.719 2,2.333 2,2.333 2.563,2.333 false 2.24,1.719 2.24,2.094 2.24,2.094 2.563,2.094 false 1.771,1.552 1.771,0.896 1.771,0.896 0.823,0.896 false 1.781,1.76 1.781,2.302 1.781,2.302 0.875,2.302 false 2.344,1.542 2.344,1.323 2.344,1.323 2.542,1.323 false 2.354,1.708 2.552,1.708 false 1.615,0.208 1.969,0.438 0.354,0.229 10 false G72 0.24,3.396 0.594,3.625 0.354,0.229 10 false G4 0.073,0.063 0.583,0.396 0.51,0.333 10 false *a 2.344,4.104 2.698,4.313 0.354,0.208 10 false BAT 0.219,1.323 0.927,1.542 0.708,0.219 10 false CANH*b 0.271,1.594 0.979,1.813 0.708,0.219 10 false CANL*b 0.073,2.719 0.583,3.052 0.51,0.333 10 false *1 0.219,1.073 0.927,1.292 0.708,0.219 10 false CANH*c 0.208,0.802 0.917,1.021 0.708,0.219 10 false CANH*d 2.583,0.542 3.292,0.76 0.708,0.219 10 false CANH*e 2.583,0.813 3.292,1.031 0.708,0.219 10 false CANH*f 2.583,1.042 3.292,1.26 0.708,0.219 10 false CANH*g 0.281,1.906 0.99,2.125 0.708,0.219 10 false CANL*c 0.302,2.229 1.01,2.448 0.708,0.219 10 false CANL*d 2.604,2.5 3.208,2.719 0.604,0.219 10 false CANL*e 2.594,2.25 3.177,2.469 0.583,0.219 10 false CANL*f 2.604,2 3.219,2.219 0.615,0.219 10 false CANL*g 2.583,1.25 3.177,1.469 0.594,0.219 10 false CANH*h 2.594,1.625 3.167,1.844 0.573,0.219 10 false CANL*h

Disconnect the G72 CAN junction connector RH.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G72-1 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Spiral cable with sensor sub-assembly (Steering sensor)
G72-12 (CANL) - G4-16 (BAT)
G72-4 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Airbag sensor assembly
G72-15 (CANL) - G4-16 (BAT)
G72-6 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Power steering ECU assembly
G72-17 (CANL) - G4-16 (BAT)
G72-7 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Combination meter assembly
G72-18 (CANL) - G4-16 (BAT)
G72-8 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Air conditioning amplifier assembly
G72-19 (CANL) - G4-16 (BAT)
G72-10 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher CAN junction connector LH
G72-21 (CANL) - G4-16 (BAT)
G72-11 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher DLC3
G72-22 (CANL) - G4-16 (BAT)


Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to CAN Junction Connector RH)
*b to Spiral Cable with Sensor Sub-assembly (Steering Sensor)
*c to Airbag Sensor Assembly
*d to Power Steering ECU Assembly
*e to Combination Meter Assembly
*f to Air Conditioning Amplifier Assembly
*g to CAN Junction Connector LH
*h to DLC3


Result:
Result Proceed to
OK A
NG (CAN junction connector LH main line) B
NG (ECU or sensor bus line) C
NG (DLC3 branch line) D



A

REPLACE CAN JUNCTION CONNECTOR RH

B

2.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN J/C LH (INSTRUMENT PANEL WIRE SIDE))

C

4.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU, SENSOR)

D

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

2.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN J/C LH (INSTRUMENT PANEL WIRE SIDE))
a.
U183627E02
2.5,3.719 2.5,4.052 false 1.208,1.563 1.208,1.417 1.208,1.417 0.813,1.417 false 1.167,1.708 0.823,1.708 false 1.427,1.563 1.427,0.771 1.427,0.771 0.833,0.771 false 1.542,1.542 1.542,0.729 1.542,0.729 2.552,0.729 false 1.667,1.573 1.667,0.979 1.667,0.979 2.552,0.979 false 1.438,1.708 1.438,2.281 1.438,2.281 0.854,2.281 false 1.552,1.719 1.552,2.573 1.552,2.573 2.573,2.573 false 1.667,1.74 1.667,2.354 1.667,2.354 2.573,2.354 false 1.615,0.198 1.969,0.427 0.354,0.229 10 false G71 0.24,3.406 0.594,3.635 0.354,0.229 10 false G4 0.052,0 0.563,0.333 0.51,0.333 10 false *a 2.344,4.073 2.698,4.281 0.354,0.208 10 false BAT 0.188,1.313 0.896,1.531 0.708,0.219 10 false CANH*b 0.208,1.625 0.917,1.844 0.708,0.219 10 false CANL*b 0.052,2.573 0.563,2.906 0.51,0.333 10 false *1 0.219,0.677 0.927,0.896 0.708,0.219 10 false CANH*c 2.594,0.646 3.302,0.865 0.708,0.219 10 false CANH*d 2.594,0.896 3.302,1.115 0.708,0.219 10 false CANH*e 0.271,2.167 0.979,2.385 0.708,0.219 10 false CANL*c 2.604,2.479 3.313,2.698 0.708,0.219 10 false CANL*d 2.615,2.26 3.323,2.479 0.708,0.219 10 false CANL*e

Disconnect the G71 CAN junction connector LH (instrument panel wire side).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G71-1 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Main body ECU (Multiplex network body ECU)
G71-12 (CANL) - G4-16 (BAT)
G71-3 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Smart key ECU assembly (Certification ECU)
G71-14 (CANL) - G4-16 (BAT)
G71-4 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher CAN junction connector RH
G71-15 (CANL) - G4-16 (BAT)
G71-5 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Hybrid vehicle control computer assembly
G71-16 (CANL) - G4-16 (BAT)



Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to CAN Junction Connector LH (Instrument Panel Wire Side))
*b to Main Body ECU (Multiplex Network Body ECU)
*c to Smart Key ECU Assembly (Certification ECU)
*d to CAN Junction Connector RH
*e to Hybrid Vehicle Control Computer Assembly

Result:
Result Proceed to
OK A
NG (CAN junction connector RH main line) B
NG (ECU or sensor bus line) C



A

3.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN J/C LH (ENGINE ROOM MAIN WIRE SIDE))

B

REPAIR OR REPLACE CAN MAIN BUS LINE (CAN J/C LH (INSTRUMENT PANEL WIRE SIDE) - CAN J/C RH)

C

4.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU, SENSOR)
3.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN J/C LH (ENGINE ROOM MAIN WIRE SIDE))
a.
U159550E03
2.5,3.719 2.5,4.052 false 2.115,1.552 2.115,0.74 2.115,0.74 2.552,0.74 false 2.229,1.531 2.229,0.938 2.229,0.938 2.542,0.938 false 2.115,1.729 2.115,2.396 2.115,2.396 2.573,2.396 false 2.219,1.729 2.219,2.146 2.219,2.146 2.552,2.146 false 1.625,0.198 1.979,0.427 0.354,0.229 10 false A51 0.26,3.417 0.615,3.646 0.354,0.229 10 false G4 0.135,0.125 0.646,0.458 0.51,0.333 10 false *a 2.354,4.104 2.708,4.313 0.354,0.208 10 false BAT 2.615,0.667 3.323,0.885 0.708,0.219 10 false CANH*b 2.667,2.323 3.375,2.542 0.708,0.219 10 false CANL*b 0.198,2.625 0.708,2.958 0.51,0.333 10 false *1 2.615,0.885 3.323,1.104 0.708,0.219 10 false CANH*c 2.635,2.063 3.344,2.281 0.708,0.219 10 false CANL*c

Disconnect the A51 CAN junction connector LH (engine room main wire side).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A51-9 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher ECM
A51-20 (CANL) - G4-16 (BAT)
A51-10 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Brake booster with master cylinder assembly (Skid control ECU)
A51-21 (CANL) - G4-16 (BAT)



Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to CAN Junction Connector LH (Engine Room Main Wire Side))
*b to ECM
*c to Brake Booster with Master Cylinder Assembly (Skid Control ECU)

Result:
Result Proceed to
OK A
NG (ECU or sensor bus line) B



A

REPLACE CAN JUNCTION CONNECTOR LH

B

4.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU, SENSOR)
4.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU, SENSOR)
a.

Reconnect all wire harness connectors (CAN junction connector LH and CAN junction connector RH).


b.

Disconnect the ECU or sensor connected to the CAN bus line that is shorted to +B.

HINT:

If the ECU or sensor has multiple connectors, disconnect the connector that includes the CAN bus lines. To determine the ECU or sensor that is connected to the shorted bus line, refer to the terminals of ECU tables (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU).



c.
U159346E01
0.087,0.032 0.927,0.365 0.840,0.334 10 *1 1.622,0.756 1.930,0.938 0.309,0.181 10 G4 2.452,1.066 2.863,1.247 0.411,0.181 10 CANH 2.435,2.911 2.823,3.092 0.387,0.181 10 CANL 2.078,1.828 2.441,1.27 false 2.085,2.535 2.419,2.868 false 2.963,2.244 3.294,2.411 0.332,0.167 10 BAT 2.511,2.319 2.938,2.319 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G4-6 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G4-14 (CANL) - G4-16 (BAT)


Text in Illustration
*1 DLC3

HINT:

If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.




OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BUS LINE OR CONNECTOR