Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2014.12–2015.11
RM2170E _57 Power Source / Network _057033 NETWORKING _0278068 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check CAN Bus Line for Short to GND (RHD Models)  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminals 6 (CANH) and 4 (CG) or 14 (CANL) and 4 (CG) of the DLC3.

Symptom Trouble Area
No resistance exists between terminals 6 (CANH) and 4 (CG) or 14 (CANL) and 4 (CG) of the DLC3.
·

Short to ground in CAN main bus line

·

Short to ground in CAN branch line

·

ECM

·

Brake booster with master cylinder assembly (Skid control ECU)

·

Main body ECU (Multiplex network body ECU)

·

Air conditioning amplifier assembly

·

Power steering ECU assembly

·

Smart key ECU assembly (Certification ECU)

·

Airbag sensor assembly

·

Spiral cable with sensor sub-assembly (Steering sensor)

·

Hybrid vehicle control computer assembly

·

Combination meter assembly

·

CAN junction connector LH

·

CAN junction connector RH



WIRING DIAGRAM

C260982E07
3.979,7.979 5.708,8.167 1.729,0.188 10 false : CAN Branch Line (CANH) 3.979,8.385 5.708,8.573 1.729,0.188 10 false : CAN Branch Line (CANL) 0.854,7.99 2.771,8.177 1.917,0.188 10 false : CAN Main Bus Line (CANH) 0.854,8.406 2.771,8.594 1.917,0.188 10 false : CAN Main Bus Line (CANL) 3.448,0.219 3.865,0.406 0.417,0.188 10 false 120 Ω 2.781,0.927 3.188,1.094 0.406,0.167 10 false CANL 0.417,0.448 0.781,0.615 0.365,0.167 10 false G1 4.115,1.438 4.333,1.656 0.219,0.219 10 false G 3.021,1.438 3.219,1.604 0.198,0.167 10 false W 0.667,0.448 2.521,0.646 1.854,0.198 10 false Combination Meter Assembly 0.125,0.063 1.979,0.26 1.854,0.198 12 false V Bus: 4.115,0.927 4.552,1.094 0.438,0.167 10 false CANH 4.083,1.229 4.427,1.448 0.344,0.219 10 false 31 3.01,1.24 3.323,1.448 0.313,0.208 10 false 32 5.188,0.563 6.396,0.75 1.208,0.188 10 false x: Suspected Area 4.865,2.125 6.854,2.375 1.99,0.25 10 false CAN Junction Connector RH 1.021,6.042 1.427,6.208 0.406,0.167 10 false CANL 1.01,5.469 1.448,5.635 0.438,0.167 10 false CANH 1.563,5.469 1.792,5.635 0.229,0.167 10 false 11 2.146,5.417 2.26,5.583 0.115,0.167 10 false V 2.125,6.125 2.292,6.292 0.167,0.167 10 false W 1.563,6.052 1.813,6.271 0.25,0.219 10 false 12 2.781,5.458 3.042,5.719 0.26,0.26 10 false 8 2.729,6.083 2.979,6.354 0.25,0.271 10 false 19 2.74,3.719 2.938,3.948 0.198,0.229 10 false 4 2.698,4.448 2.927,4.656 0.229,0.208 10 false 15 0.063,6.365 0.354,6.542 0.292,0.177 10 false G34 0.385,6.365 1.969,6.74 1.583,0.375 10 false Air Conditioning Amplifier Assembly 0.51,4.698 2.083,5.052 1.573,0.354 10 false Airbag Sensor Assembly 1.073,4.406 1.479,4.573 0.406,0.167 10 false CANL 1.052,3.854 1.49,4.021 0.438,0.167 10 false CANH 2.156,3.719 2.354,3.969 0.198,0.25 10 false B 2.135,4.49 2.333,4.688 0.198,0.198 10 false W 0.177,4.698 0.479,4.875 0.302,0.177 10 false G18 1.583,3.792 1.875,4.021 0.292,0.229 10 false 13 1.594,4.417 1.781,4.583 0.188,0.167 10 false 22 4.552,2.125 4.917,2.406 0.365,0.281 10 false G72 3.021,1.677 3.313,1.917 0.292,0.24 10 false 18 4.135,1.677 4.406,1.875 0.271,0.198 10 false 7 3.031,7.229 3.333,7.5 0.302,0.271 10 false 21 4.104,7.229 4.49,7.531 0.385,0.302 10 false 10 2.75,2.021 2.958,2.188 0.208,0.167 10 false 1 2.698,2.688 2.948,2.927 0.25,0.24 10 false 12 1.042,2.667 1.448,2.833 0.406,0.167 10 false CANL 2.125,2.76 2.281,2.927 0.156,0.167 10 false W 0.094,2.979 0.458,3.146 0.365,0.167 10 false G30 1.031,2.115 1.469,2.281 0.438,0.167 10 false CANH 1.563,2.125 1.781,2.323 0.219,0.198 10 false 4 1.563,2.677 1.802,2.885 0.24,0.208 10 false 3 2.167,1.969 2.344,2.115 0.177,0.146 10 false P 0.427,2.979 2.594,3.427 2.167,0.448 10 false Spiral Cable with Sensor Sub-assembly (Steering Sensor) 5.031,5.313 5.219,5.573 0.188,0.26 10 false W 6.073,5.073 6.479,5.24 0.406,0.167 10 false CANL 5.917,4.74 6.354,4.906 0.438,0.167 10 false CANH 4.448,4.563 4.719,4.781 0.271,0.219 10 false 11 4.448,5.292 4.833,5.573 0.385,0.281 10 false 22 5.813,5.281 6.01,5.448 0.198,0.167 10 false 14 5.625,4.615 5.802,4.781 0.177,0.167 10 false 6 6.135,5.354 6.458,5.542 0.323,0.188 10 false G4 6.406,5.354 6.802,5.542 0.396,0.188 10 false DLC3 5,4.563 5.365,4.823 0.365,0.26 10 false GR 5.802,3.76 7.135,4.125 1.333,0.365 10 false Power Steering ECU Assembly 5.948,3.49 6.354,3.656 0.406,0.167 10 false CANL 5.948,2.833 6.385,3 0.438,0.167 10 false CANH 5.719,2.802 5.906,2.969 0.188,0.167 10 false 7 4.469,2.823 4.656,2.99 0.188,0.167 10 false 6 4.427,3.531 4.698,3.792 0.271,0.26 10 false 17 5.01,3.563 5.271,3.802 0.26,0.24 10 false W 4.99,2.76 5.281,2.927 0.292,0.167 10 false LG 5.719,3.469 5.906,3.635 0.188,0.167 10 false 8 5.563,3.76 5.823,4.063 0.26,0.302 10 false G6

C251631E10
3.948,8.073 6.073,8.292 2.125,0.219 10 false : CAN Branch Line (CANH) 3.969,8.479 5.75,8.708 1.781,0.229 10 false : CAN Branch Line (CANL) 0.854,8.052 2.885,8.281 2.031,0.229 10 false : CAN Main Bus Line (CANH) 0.854,8.448 2.833,8.719 1.979,0.271 10 false : CAN Main Bus Line (CANL) 0.344,3.063 2.021,3.396 1.677,0.333 10 false Smart Key ECU Assembly (Certification ECU) 0.573,1.063 2.375,1.677 1.802,0.615 10 false CAN Junction Connector LH 0.073,3.063 0.719,3.5 0.646,0.438 10 false G79 0.365,5.115 1.823,5.521 1.458,0.406 10 false Hybrid Vehicle Control Computer Assembly 0.083,5.115 0.583,5.583 0.5,0.469 10 false G81 1.271,4.198 1.667,4.667 0.396,0.469 10 false 25 1.271,4.854 1.667,5.344 0.396,0.49 10 false 24 5.917,2.198 7.094,2.854 1.177,0.656 10 false Main Body ECU (Multiplex Network Body ECU) 5.583,2.208 6.031,2.573 0.448,0.365 10 false G59 5.938,4.115 7.156,5.25 1.219,1.135 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 5.604,4.135 6.188,4.573 0.583,0.438 10 false A41 4.458,7.219 4.99,7.823 0.531,0.604 10 false ECM 4.167,7.208 4.438,7.458 0.271,0.25 10 false A40 2.354,6.906 3.083,7.323 0.729,0.417 10 false CANL 0.792,4.854 1.552,5.26 0.76,0.406 10 false CA1L 0.792,4.219 1.406,4.625 0.615,0.406 10 false CA1H 1.271,2.198 1.688,2.583 0.417,0.385 10 false 14 4.063,1.188 4.448,1.469 0.385,0.281 10 false 1 1.271,2.792 1.771,3.167 0.5,0.375 10 false 15 0.813,2.792 1.396,3.104 0.583,0.313 10 false CANL 0.813,2.198 1.448,2.573 0.635,0.375 10 false CANH 2.688,0.823 3.146,1.156 0.458,0.333 10 false G71 2.156,2.302 2.656,2.635 0.5,0.333 10 false G71 2.167,2.667 2.688,3.01 0.521,0.344 10 false G71 2.167,4.333 2.656,4.656 0.49,0.323 10 false G71 2.177,4.698 2.667,5.063 0.49,0.365 10 false G71 2.688,5.51 3.313,5.99 0.625,0.479 10 false A51 3.469,5.51 3.979,5.958 0.51,0.448 10 false A51 3.979,3.313 4.51,3.625 0.531,0.313 10 false A51 3.969,3.677 4.51,3.99 0.542,0.313 10 false A51 3.438,0.823 3.813,1.177 0.375,0.354 10 false G71 3.958,1.417 4.427,1.677 0.469,0.26 10 false G71 3.958,1.771 4.396,2.042 0.438,0.271 10 false G71 5.729,1.281 6.073,1.583 0.344,0.302 10 false 14 4.021,2.01 4.458,2.354 0.438,0.344 10 false 12 3.979,3.135 4.448,3.427 0.469,0.292 10 false 10 4,3.875 4.406,4.188 0.406,0.313 10 false 21 2.292,2.104 2.656,2.448 0.365,0.344 10 false 3 3.833,0.813 4.25,1.104 0.417,0.292 10 false 4 2.438,0.802 2.875,1.188 0.438,0.385 10 false 15 2.229,2.885 2.49,3.063 0.26,0.177 10 false 14 2.26,4.125 2.708,4.438 0.448,0.313 10 false 5 2.229,4.917 2.76,5.271 0.531,0.354 10 false 16 5.75,1.896 6.01,2.073 0.26,0.177 10 false 13 5.99,1.885 6.635,2.198 0.646,0.313 10 false CANL 5.99,1.302 6.594,1.677 0.604,0.375 10 false CANH 5.688,3.229 6.177,3.656 0.49,0.427 10 false 37 5.688,3.771 6.115,4.146 0.427,0.375 10 false 38 5.979,3.781 6.719,4.219 0.74,0.438 10 false CA1L 5.958,3.219 6.688,3.708 0.729,0.49 10 false CA1H 2.469,6.635 2.938,7.052 0.469,0.417 10 false 26 2.448,5.521 2.969,5.896 0.521,0.375 10 false 20 3.698,6.906 4.344,7.292 0.646,0.385 10 false CANH 3.667,6.646 4.146,6.969 0.479,0.323 10 false 13 3.813,5.51 4.229,5.865 0.417,0.354 10 false 9 3.042,7.531 3.938,8 0.896,0.469 10 false 120Ω 5.125,0.292 6.51,0.708 1.385,0.417 10 false x:Suspected Area 4.969,3.865 5.375,4.167 0.406,0.302 10 false W 4.99,3.125 5.323,3.458 0.333,0.333 10 false B 2.542,6.229 3.104,6.625 0.563,0.396 10 false W 3.708,6.24 4.156,6.583 0.448,0.344 10 false L 1.625,2.865 2.021,3.25 0.396,0.385 10 false W 1.635,2.104 1.969,2.521 0.333,0.417 10 false L 5.031,1.979 5.427,2.313 0.396,0.333 10 false W 5.031,1.198 5.344,1.5 0.313,0.302 10 false R 2.594,0.396 2.99,0.656 0.396,0.26 10 false W 3.698,0.406 4.104,0.698 0.406,0.292 10 false SB 1.646,4.896 2.146,5.375 0.5,0.479 10 false W 1.625,4.135 1.99,4.5 0.365,0.365 10 false BE

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control main switch (ON/OFF switch), wait at least 60 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more.

·

After the repair, perform CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT TO GND IN CAN BUS LINE (CAN J/C RH)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U183623E02
1.208,1.552 1.208,1.438 1.208,1.438 0.813,1.438 false 1.177,1.698 0.833,1.698 false 1.542,1.542 1.542,1.167 1.542,1.167 0.823,1.167 false 1.875,1.552 1.875,0.625 1.875,0.625 2.542,0.625 false 2,1.552 2,0.896 2,0.896 2.542,0.896 false 2.229,1.563 2.229,1.156 2.229,1.156 2.542,1.156 false 1.552,1.719 1.552,1.958 1.552,1.958 0.854,1.958 false 1.896,1.708 1.896,2.573 1.896,2.573 2.573,2.573 false 2.01,1.708 2.01,2.323 2.01,2.323 2.573,2.323 false 2.229,1.708 2.229,2.094 2.229,2.094 2.552,2.094 false 1.771,1.542 1.771,0.885 1.771,0.885 0.823,0.885 false 1.781,1.708 1.781,2.24 1.781,2.24 0.875,2.24 false 2.344,1.563 2.344,1.354 2.344,1.354 2.542,1.354 false 2.354,1.708 2.552,1.708 false 1.719,3.156 1.719,2.625 1.719,2.625 1.333,2.625 false 1.594,0.188 1.948,0.417 0.354,0.229 10 false G72 0.24,3.396 0.594,3.625 0.354,0.229 10 false G4 0.052,0 0.563,0.333 0.51,0.333 10 false *a 1.073,2.531 1.427,2.74 0.354,0.208 10 false CG 0.219,1.333 0.927,1.552 0.708,0.219 10 false CANH*b 0.271,1.594 0.979,1.813 0.708,0.219 10 false CANL*b 0.052,2.552 0.563,2.885 0.51,0.333 10 false *1 0.219,1.052 0.927,1.271 0.708,0.219 10 false CANH*c 0.208,0.781 0.917,1 0.708,0.219 10 false CANH*d 2.594,0.542 3.302,0.76 0.708,0.219 10 false CANH*e 2.583,0.823 3.292,1.042 0.708,0.219 10 false CANH*f 2.594,1.083 3.302,1.302 0.708,0.219 10 false CANH*g 0.292,1.865 1,2.083 0.708,0.219 10 false CANL*c 0.302,2.146 1.01,2.365 0.708,0.219 10 false CANL*d 2.604,2.5 3.208,2.719 0.604,0.219 10 false CANL*e 2.615,2.25 3.198,2.469 0.583,0.219 10 false CANL*f 2.604,2.021 3.219,2.24 0.615,0.219 10 false CANL*g 2.583,1.281 3.177,1.5 0.594,0.219 10 false CANH*h 2.583,1.635 3.156,1.854 0.573,0.219 10 false CANL*h

Disconnect the G72 CAN junction connector RH.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G72-1 (CANH) - G4-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Spiral cable with sensor sub-assembly (Steering sensor)
G72-12 (CANL) - G4-4 (CG)
G72-4 (CANH) - G4-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Airbag sensor assembly
G72-15 (CANL) - G4-4 (CG)
G72-6 (CANH) - G4-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Power steering ECU assembly
G72-17 (CANL) - G4-4 (CG)
G72-7 (CANH) - G4-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Combination meter assembly
G72-18 (CANL) - G4-4 (CG)
G72-8 (CANH) - G4-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Air conditioning amplifier assembly
G72-19 (CANL) - G4-4 (CG)
G72-10 (CANH) - G4-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher CAN junction connector LH
G72-21 (CANL) - G4-4 (CG)
G72-11 (CANH) - G4-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher DLC3
G72-22 (CANL) - G4-4 (CG)


Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to CAN Junction Connector RH)
*b to Spiral Cable with Sensor Sub-assembly (Steering Sensor)
*c to Airbag Sensor Assembly
*d to Power Steering ECU Assembly
*e to Combination Meter Assembly
*f to Air Conditioning Amplifier Assembly
*g to CAN Junction Connector LH
*h to DLC3


Result:
Result Proceed to
OK A
NG (CAN junction connector LH main line) B
NG (ECU or sensor bus line) C
NG (DLC3 branch line) D



A

REPLACE CAN JUNCTION CONNECTOR RH

B

2.CHECK FOR SHORT TO GND IN CAN BUS LINE (CAN J/C LH (INSTRUMENT PANEL WIRE SIDE))

C

4.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU, SENSOR)

D

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

2.CHECK FOR SHORT TO GND IN CAN BUS LINE (CAN J/C LH (INSTRUMENT PANEL WIRE SIDE))
a.
U183628E02
1.208,1.552 1.208,1.396 1.208,1.396 0.813,1.396 false 1.177,1.698 0.833,1.698 false 1.427,1.542 1.427,0.76 1.427,0.76 0.833,0.76 false 1.542,1.542 1.542,0.74 1.542,0.74 2.552,0.74 false 1.667,1.552 1.667,0.969 1.667,0.969 2.552,0.969 false 1.438,1.729 1.438,2.302 1.438,2.302 0.854,2.302 false 1.552,1.719 1.552,2.406 1.552,2.406 2.573,2.406 false 1.667,1.719 1.667,2.167 1.667,2.167 2.573,2.167 false 1.729,3.156 1.729,2.688 1.729,2.688 1.365,2.688 false 1.615,0.188 1.969,0.417 0.354,0.229 10 false G71 0.25,3.406 0.604,3.635 0.354,0.229 10 false G4 0.052,0 0.563,0.333 0.51,0.333 10 false *a 1.094,2.583 1.448,2.792 0.354,0.208 10 false CG 0.208,1.292 0.917,1.51 0.708,0.219 10 false CANH*b 0.25,1.604 0.958,1.823 0.708,0.219 10 false CANL*b 0.052,2.552 0.563,2.885 0.51,0.333 10 false *1 0.229,0.656 0.938,0.875 0.708,0.219 10 false CANH*c 2.583,0.646 3.24,0.865 0.656,0.219 10 false CANH*d 2.583,0.885 3.219,1.104 0.635,0.219 10 false CANH*e 0.26,2.198 0.969,2.417 0.708,0.219 10 false CANL*c 2.615,2.323 3.24,2.542 0.625,0.219 10 false CANL*d 2.604,2.083 3.24,2.302 0.635,0.219 10 false CANL*e

Disconnect the G71 CAN junction connector LH (instrument panel wire side).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G71-1 (CANH) - G4-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Main body ECU (Multiplex network body ECU)
G71-12 (CANL) - G4-4 (CG)
G71-3 (CANH) - G4-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Smart key ECU assembly (Certification ECU)
G71-14 (CANL) - G4-4 (CG)
G71-4 (CANH) - G4-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher CAN junction connector RH
G71-15 (CANL) - G4-4 (CG)
G71-5 (CANH) - G4-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Hybrid vehicle control computer assembly
G71-16 (CANL) - G4-4 (CG)



Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to CAN Junction Connector LH (Instrument Panel Wire Side))
*b to Main Body ECU (Multiplex Network Body ECU)
*c to Smart Key ECU Assembly (Certification ECU)
*d to CAN Junction Connector RH
*e to Hybrid Vehicle Control Computer Assembly

Result:
Result Proceed to
OK A
NG (CAN junction connector RH main line) B
NG (ECU or sensor bus line) C



A

3.CHECK FOR SHORT TO GND IN CAN BUS LINE (CAN J/C LH (ENGINE ROOM MAIN WIRE SIDE))

B

REPAIR OR REPLACE CAN MAIN BUS LINE (CAN J/C LH (INSTRUMENT PANEL WIRE SIDE) - CAN J/C RH)

C

4.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU, SENSOR)
3.CHECK FOR SHORT TO GND IN CAN BUS LINE (CAN J/C LH (ENGINE ROOM MAIN WIRE SIDE))
a.
U183624E02
2.115,1.542 2.115,0.74 2.115,0.74 2.552,0.74 false 2.229,1.552 2.229,0.969 2.229,0.969 2.542,0.969 false 2.115,1.74 2.115,2.417 2.115,2.417 2.573,2.417 false 2.229,1.719 2.229,2.146 2.229,2.146 2.563,2.146 false 1.719,3.167 1.719,2.594 1.719,2.594 1.344,2.594 false 1.615,0.198 1.969,0.427 0.354,0.229 10 false A51 0.24,3.406 0.594,3.635 0.354,0.229 10 false G4 0.052,0 0.563,0.333 0.51,0.333 10 false *a 1.052,2.49 1.406,2.698 0.354,0.208 10 false CG 2.604,0.656 3.313,0.875 0.708,0.219 10 false CANH*b 2.615,2.333 3.323,2.552 0.708,0.219 10 false CANL*b 0.052,2.552 0.563,2.885 0.51,0.333 10 false *1 2.604,0.896 3.313,1.115 0.708,0.219 10 false CANH*c 2.604,2.063 3.313,2.281 0.708,0.219 10 false CANL*c

Disconnect the A51 CAN junction connector LH (engine room main wire side).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A51-9 (CANH) - G4-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher ECM
A51-20 (CANL) - G4-4 (CG)
A51-10 (CANH) - G4-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Brake booster with master cylinder assembly (Skid control ECU)
A51-21 (CANL) - G4-4 (CG)



Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to CAN Junction Connector LH (Engine Room Main Wire Side))
*b to ECM
*c to Brake Booster with Master Cylinder Assembly (Skid Control ECU)

Result:
Result Proceed to
OK A
NG (ECU or sensor bus line) B



A

REPLACE CAN JUNCTION CONNECTOR LH

B

4.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU, SENSOR)
4.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU, SENSOR)
a.

Reconnect all wire harness connectors (CAN junction connector LH and CAN junction connector RH).


b.

Disconnect the ECU or sensor connected to the CAN bus line that is shorted to ground.

HINT:

If the ECU or sensor has multiple connectors, disconnect the connector that includes the CAN bus lines. To determine the ECU or sensor that is connected to the shorted bus line, refer to the terminals of ECU tables (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU).



c.
U183518E02
2.063,1.906 2.427,1.354 false 2.083,2.531 2.417,2.865 false 1.615,1.896 1.094,1.24 false 0.083,0.031 0.927,0.365 0.844,0.333 10 false *1 1.625,0.802 1.938,0.979 0.313,0.177 10 false G4 2.448,1.167 2.854,1.344 0.406,0.177 10 false CANH 2.438,2.906 2.823,3.083 0.385,0.177 10 false CANL 0.833,1.083 1.208,1.354 0.375,0.271 10 false CG

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G4-6 (CANH) - G4-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G4-14 (CANL) - G4-4 (CG)


Text in Illustration
*1 DLC3

HINT:

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.




OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BUS LINE OR CONNECTOR